87 results (0,17670 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

White Fascia Capping Board External Corner Joint Trim - 135 Degree x 300mm

White Fascia Capping Board External Corner Joint Trim - 135 Degree x 300mm

135 Degree corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. 135 degree corners (or 45 degree corners as they are also called) are usually found above a bay window on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.All corner trims can be cut to size with a standard hacksaw or fine toothed saw

GBP 4.75
1

Rosewood Fascia Capping Board Joint - 300mm

Rosewood Fascia Capping Board Joint - 300mm

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.93
1

Anthracite Grey Fascia Capping Board Joint - 300mm

Anthracite Grey Fascia Capping Board Joint - 300mm

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.93
1

Golden Oak Fascia Capping Board Joint - 300mm

Golden Oak Fascia Capping Board Joint - 300mm

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.93
1

Rosewood Fascia Capping Board External Corner - 300mm

Rosewood Fascia Capping Board External Corner - 300mm

Corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 8.40
1

Black Ash Woodgrain Fascia Capping Board Joint - 300mm

Black Ash Woodgrain Fascia Capping Board Joint - 300mm

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.93
1

Rosewood Fascia Capping Board Internal Corner - 300mm

Rosewood Fascia Capping Board Internal Corner - 300mm

Internal corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. Internal corners are usually found at the foot of a valley on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Internal corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.40
1

Black Ash Woodgrain Fascia Capping Board Internal Corner - 300mm

Black Ash Woodgrain Fascia Capping Board Internal Corner - 300mm

Internal corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. Internal corners are usually found at the foot of a valley on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Internal corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.40
2

Golden Oak Fascia Capping Board Internal Corner - 300mm

Golden Oak Fascia Capping Board Internal Corner - 300mm

Internal corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. Internal corners are usually found at the foot of a valley on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Internal corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.40
1

Soffit Vent Strip - 50mm x 2.5mtr White

Soffit Vent Strip - 50mm x 2.5mtr White

The G800 Continuous Soffit Ventilator is designed to provide a solution to roof ventilation where a traditional soffit board is specified. The airflow passage consists of evenly spaced slots specifically sized to prohibit large insects gaining access but wide enoughandnbsp;not to be blocked by debris, paint or water droplets.The G800 is usually fixed to the back of the fascia board. A soffit board is then slotted into the adjustable mouth of the vent and then fixed back to the wall as usual. This vent will accept any type of soffit with a thickness of between 4mm and 12mm.

GBP 4.57
1

Bullnose Fascia 135 Degree External Corner - 327mm x 50mm White

Bullnose Fascia 135 Degree External Corner - 327mm x 50mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This corner is 327mm long.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 7.78
1

Bullnose Fascia 135 Degree Internal Corner - 327mm x 50mm White

Bullnose Fascia 135 Degree Internal Corner - 327mm x 50mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This corner is 327mm long.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 7.78
1

Bullnose Fascia Double Ended Joiner - 600mm x 40mm White

Bullnose Fascia Double Ended Joiner - 600mm x 40mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This joiner is 600mm long, meaning that you can create 2 joints from 1 piece.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 7.18
1

Bullnose Fascia Double Ended External Corner - 600mm x 40mm White

Bullnose Fascia Double Ended External Corner - 600mm x 40mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This corner is 600mm long, meaning that you can create 2 joints from 1 piece.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 5.98
1

Fascia Bargeboard Finial - 340mm White

Fascia Bargeboard Finial - 340mm White

Bargeboard finials are a more decorative way of covering the joint between the two bargeboards at the apex of the roof.To enable the barge boards to expand and contract correctly in a different range of temperatures, one side of the finial should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.This rule should be always applied to any corner or joint cover on any PVC fascia installation.

GBP 8.74
1

Ogee Fascia Corner - 300mm White

Ogee Fascia Corner - 300mm White

Corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint. Fascia corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 5.98
1

Ogee Fascia Joint Double Ended - 500mm White

Ogee Fascia Joint Double Ended - 500mm White

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 8.59
1