138 results (0,17625 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Special Offer Vectaire Maxi BY LCDRH Model

Special Offer Vectaire Maxi BY LCDRH Model

Description General up to 163 litre/sec at 50Pa - max 177 litre/sec capacity sfp down to 0.40 W/l/s summer bypass which allows the airflow to bypass the heat exchanger automatically when internal and external temperatures are between adjustable setpoints. frost-stat - proportionally reduces intake motor speed as temperature falls - activated when the outside temperature is between +8ºC and -3ºC. run-time and power outage counters easy to install and maintain easy to access G3 filters universal handing for models without humidistat - left or right (see separate diagram for handing on humidistat models) for fitting vertically into lofts, or cupboards - wall fixing bracket supplied variable low (trickle), boost and purge options for each motor boost speed can be activated by a 230V switched live from: a light switch (if more than one light switch is used, each one must be a double pole switch) Remote humidistat (230V - DRH240) Passive infra red (230V - PIRFF) Thermostat (230V - THM) Remote switch/pull cord - 230V low noise levels low running costs CONTROL FEATURES - STANDARD independent variable speed adjustment for each motor for trickle, boost and purge speeds. adjustable boost speed over-run timer from 0 to 30 minutes. adjustable boost speed delay from 0 to 5 minutes remote purge cable connection on circuit board (for optional purge facility) adjustable night time boost and purge inhibitor integral frost-stat - proportionally reduces intake motor speed as temperature falls automatic summer bypass CONTROL FEATURES - FACTORY SET change of ductwork handing on humidistat version (trip point can be set at manufacture) integral humidistat - proportionally increases motor speeds with rising humidity 0-10V connections can be added for: BMS - for remote motor shut-off CO2 detector home automation system relay for external pre-heater 3 speed selector switch optional remote purge cable - factory connected - adjustable over-run timer from 0 to 250 minutes, Pre-set to 15 minutes (adjustable at factory) holiday mode for reduced speeds when property is unoccupied (factory set option) - default setting is 50% of trickle speed run-time and power outage counters downloadable via QR code Specification casing from steel sheet - epoxy paint finish foam construction lining EPS internal components provide acoustic and thermal enhancement low energy EC brushless motor with single width, single inlet, direct drive, forward curved impellors operates in temperature up to 60ºC easy to access standard, disposable G3 filters counter flow heat exchanger Compliance Building Regulations for enhanced energy saving capability Building Regulations for reliable, efficient ventilation EU RoHS Directive Compliant. Complies with IEC60335-2-80, LVD2006/95/CE and EMC2014/30/UE (European Directive against radio interference and electro-magnetic compatibility manufactured in UK to ISO 9001:2015 and 14001:2015 CE marked SAP PCDB Listed Range WHHR Maxi/ BY - bypass, universal WHHR Maxi/ BLH - bypass, left drain humidistat WHHR Maxi/ BRH - bypass, right drain, humidistat Maxi BY+LCD - bypass, universal, integral LCD Maxi+LHHLCD - bypass, left drain, humidistat, integral LCD Maxi+RHHLCD - bypass, right drain, humidistat, integral LC

GBP 1320.00
1

Special Offer Vectaire Maxi AT BY LCDRH Model

Special Offer Vectaire Maxi AT BY LCDRH Model

Description General up to 163 litre/sec at 50Pa - max 177 litre/sec capacity sfp down to 0.40 W/l/s summer bypass which allows the airflow to bypass the heat exchanger automatically when internal and external temperatures are between adjustable setpoints. frost-stat - proportionally reduces intake motor speed as temperature falls - activated when the outside temperature is between +8ºC and -3ºC. run-time and power outage counters easy to install and maintain easy to access G3 filters universal handing for models without humidistat - left or right (see separate diagram for handing on humidistat models) for fitting vertically into lofts, or cupboards - wall fixing bracket supplied variable low (trickle), boost and purge options for each motor boost speed can be activated by a 230V switched live from: a light switch (if more than one light switch is used, each one must be a double pole switch) Remote humidistat (230V - DRH240) Passive infra red (230V - PIRFF) Thermostat (230V - THM) Remote switch/pull cord - 230V low noise levels low running costs CONTROL FEATURES - STANDARD independent variable speed adjustment for each motor for trickle, boost and purge speeds. adjustable boost speed over-run timer from 0 to 30 minutes. adjustable boost speed delay from 0 to 5 minutes remote purge cable connection on circuit board (for optional purge facility) adjustable night time boost and purge inhibitor integral frost-stat - proportionally reduces intake motor speed as temperature falls automatic summer bypass CONTROL FEATURES - FACTORY SET change of ductwork handing on humidistat version (trip point can be set at manufacture) integral humidistat - proportionally increases motor speeds with rising humidity 0-10V connections can be added for: BMS - for remote motor shut-off CO2 detector home automation system relay for external pre-heater 3 speed selector switch optional remote purge cable - factory connected - adjustable over-run timer from 0 to 250 minutes, Pre-set to 15 minutes (adjustable at factory) holiday mode for reduced speeds when property is unoccupied (factory set option) - default setting is 50% of trickle speed run-time and power outage counters downloadable via QR code Specification casing from steel sheet - epoxy paint finish foam construction lining EPS internal components provide acoustic and thermal enhancement low energy EC brushless motor with single width, single inlet, direct drive, forward curved impellors operates in temperature up to 60ºC easy to access standard, disposable G3 filters counter flow heat exchanger Compliance Building Regulations for enhanced energy saving capability Building Regulations for reliable, efficient ventilation EU RoHS Directive Compliant. Complies with IEC60335-2-80, LVD2006/95/CE and EMC2014/30/UE (European Directive against radio interference and electro-magnetic compatibility manufactured in UK to ISO 9001:2015 and 14001:2015 CE marked SAP PCDB Listed Range WHHR Maxi/ BY - bypass, universal WHHR Maxi/ BLH - bypass, left drain humidistat WHHR Maxi/ BRH - bypass, right drain, humidistat Maxi BY+LCD - bypass, universal, integral LCD Maxi+LHHLCD - bypass, left drain, humidistat, integral LCD Maxi+RHHLCD - bypass, right drain, humidistat, integral LC

GBP 1560.00
1

Nuaire Xboxer XBC-55 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-55 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-55 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal) Standard model is available, additional units with extras are available include the electric preheater model and the Low-Pressure Hot Water (LPHW) heater model. Supplied with terminal box for supply and extract fan motor wiring and for interfacing to custom built control panels Nuaire XBC range of high efficiency heat recovery ventilation units designed for ceiling void applications and are suitable for external use with weather roof. Designed to save energy, improve indoor air quality, and provide the lowest noise breakout when used with Nuaire matched attenuators. Please note that all XBC units are supplied as eft hand units as standard, unless other wise stated on your order. Key Features: High heat exchange efficiency - Up to 95% Low noise Units are aluzinc, asymmetric, high mass, double skinned wall construction with specialist acoustic treatment Compact & flexible - lowest case height (by duty) with unique supply/extract are on unit centreline, intake/extract connections are configurable on site to either side of the unit. Optimum performance – Backward curved impellers and IP54 EC motors provide low specific fan powers and step-less speed control without tonal noise generation. Blowers are ErP 2015 compliant. The unit is designed for side access as standard and must be installed with a minimum of 260mm clearance from a wall or barrier. This will provide access to filters, coil, fan, heat exchanger condensate tray and pump. Technical Features Up to 75% efficient Voltage / Phase / Frequency – 230V / 1 phase / 50 Hz Max operating temperature – 45°C Maximum fan speed (RPM) - 2400 Unit Weight (kg) – 375 Sound level @3m dB(A): 35 – 58 G4 extract and supply filters Counter plate heat exchanger 100% bypass Dimensions (standard model)L x W x D – 1900mm x 1560mm x 407mm

GBP 17728.51
1

Nuaire Xboxer XBC-10 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-10 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-10 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal) Standard model is available, additional units with extras are available include the electric preheater model and the Low-Pressure Hot Water (LPHW) heater model. Supplied with terminal box for supply and extract fan motor wiring and for interfacing to custom built control panels Nuaire XBC range of high efficiency heat recovery ventilation units designed for ceiling void applications and are suitable for external use with weather roof. Designed to save energy, improve indoor air quality, and provide the lowest noise breakout when used with Nuaire matched attenuators. Please note that all XBC units are supplied as eft hand units as standard, unless other wise stated on your order. Key Features: High heat exchange efficiency - Up to 95% Low noise Units are aluzinc, asymmetric, high mass, double skinned wall construction with specialist acoustic treatment Compact & flexible - lowest case height (by duty) with unique supply/extract are on unit centreline, intake/extract connections are configurable on site to either side of the unit. Optimum performance – Backward curved impellers and IP54 EC motors provide low specific fan powers and step-less speed control without tonal noise generation. Blowers are ErP 2015 compliant. The unit is designed for side access as standard and must be installed with a minimum of 260mm clearance from a wall or barrier. This will provide access to filters, coil, fan, heat exchanger condensate tray and pump. Technical Features Up to 75% efficient Voltage / Phase / Frequency – 230V / 1 phase / 50 Hz Input Power (W) - 160 Max operating temperature – 55°C Maximum fan speed (RPM) - 3200 Unit Weight (kg) – 195 Sound level @3m dB(A) – 24 – 46 G4 extract and supply filters Counter plate heat exchanger 100% bypass DimensionsL x W x D – 1600mm x 1000mm x 260mm Benefits of working with BPC Ventilation

GBP 7636.20
1

Nuaire Xboxer XBC-65 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-65 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-65 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal) Standard model is available, additional units with extras are available include the electric preheater model and the Low-Pressure Hot Water (LPHW) heater model. Supplied with terminal box for supply and extract fan motor wiring and for interfacing to custom built control panels Nuaire XBC range of high efficiency heat recovery ventilation units designed for ceiling void applications and are suitable for external use with weather roof. Designed to save energy, improve indoor air quality, and provide the lowest noise breakout when used with Nuaire matched attenuators. Please note that all XBC units are supplied as eft hand units as standard, unless otherwise stated on your order. Key Features: High heat exchange efficiency - Up to 95% Low noise Units are aluzinc, asymmetric, high mass, double skinned wall construction with specialist acoustic treatment Compact & flexible - lowest case height (by duty) with unique supply/extract are on unit centreline, intake/extract connections are configurable on site to either side of the unit. Optimum performance – Backward curved impellers and IP54 EC motors provide low specific fan powers and step-less speed control without tonal noise generation. Blowers are ErP 2015 compliant. The unit is designed for side access as standard and must be installed with a minimum of 260mm clearance from a wall or barrier. This will provide access to filters, coil, fan, heat exchanger condensate tray and pump. Technical Features Up to 75% efficient Voltage / Phase / Frequency – 230V / 1 phase / 50 Hz Max operating temperature – 40°C Maximum fan speed (RPM) - 1850 Unit Weight (kg) – 476 Sound level @3m dB(A): 35 – 57 G4 extract and supply filters Counter plate heat exchanger 100% bypass Dimensions (standard model)L x W x D – 1913mm x 1570mm x 624mm

GBP 20293.07
1

Nuaire Xboxer XBC-25 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-25 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-25 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal) Standard model is available, additional units with extras are available include the electric preheater model and the Low-Pressure Hot Water (LPHW) heater model. Supplied with terminal box for supply and extract fan motor wiring and for interfacing to custom built control panels Nuaire XBC range of high efficiency heat recovery ventilation units designed for ceiling void applications and are suitable for external use with weather roof. Designed to save energy, improve indoor air quality, and provide the lowest noise breakout when used with Nuaire matched attenuators. Please note that all XBC units are supplied as eft hand units as standard, unless other wise stated on your order. Key Features: High heat exchange efficiency - Up to 95% Low noise Units are aluzinc, asymmetric, high mass, double skinned wall construction with specialist acoustic treatment Compact & flexible - lowest case height (by duty) with unique supply/extract are on unit centreline, intake/extract connections are configurable on site to either side of the unit. Optimum performance – Backward curved impellers and IP54 EC motors provide low specific fan powers and step-less speed control without tonal noise generation. Blowers are ErP 2015 compliant. The unit is designed for side access as standard and must be installed with a minimum of 260mm clearance from a wall or barrier. This will provide access to filters, coil, fan, heat exchanger condensate tray and pump. Technical Features Up to 75% efficient Voltage / Phase / Frequency – 230V / 1 phase / 50 Hz Max operating temperature – 60°C Maximum fan speed (RPM) - 3700 Unit Weight (kg) – 242 Sound level @3m dB(A): 40 – 64 G4 extract and supply filters Counter plate heat exchanger 100% bypass Dimensions (standard model)L x W x D – 1700mm x 1150mm x 340mm Benefits of working with BPC Ventilation Number 1 leading MVHR and ventilation system specialists Large range of systems for domestic and commercial applications

GBP 11130.25
1

Nuaire Xboxer XBC-15 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-15 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-15 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal) Standard model is available, additional units with extras are available include the electric preheater model and the Low-Pressure Hot Water (LPHW) heater model. Supplied with terminal box for supply and extract fan motor wiring and for interfacing to custom built control panels Nuaire XBC range of high efficiency heat recovery ventilation units designed for ceiling void applications and are suitable for external use with weather roof. Designed to save energy, improve indoor air quality, and provide the lowest noise breakout when used with Nuaire matched attenuators. Please note that all XBC units are supplied as eft hand units as standard, unless other wise stated on your order. Key Features: High heat exchange efficiency - Up to 95% Low noise Units are aluzinc, asymmetric, high mass, double skinned wall construction with specialist acoustic treatment Compact & flexible - lowest case height (by duty) with unique supply/extract are on unit centreline, intake/extract connections are configurable on site to either side of the unit. Optimum performance – Backward curved impellers and IP54 EC motors provide low specific fan powers and step-less speed control without tonal noise generation. Blowers are ErP 2015 compliant. The unit is designed for side access as standard and must be installed with a minimum of 260mm clearance from a wall or barrier. This will provide access to filters, coil, fan, heat exchanger condensate tray and pump. Technical Features Up to 75% efficient Voltage / Phase / Frequency – 230V / 1 phase / 50 Hz Input Power (W) - 160 Max operating temperature – 60°C Maximum fan speed (RPM) - 4000 Unit Weight (kg) – 195 Sound level @3m dB(A) – 26 – 51 G4 extract and supply filters Counter plate heat exchanger 100% bypass DimensionsL x W x D – 1600mm x 1000mm x 260mm Benefits of working with BPC Ventilation Number 1 leading MVHR and ventilation system specialists Large range of

GBP 8026.10
1

Nuaire Xboxer XBC-45 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-45 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal)

Nuaire Xboxer XBC-45 Commercial Heat Exchange Unit - (Price Varies Upon Appraisal) Standard model is available, additional units with extras are available include the electric preheater model and the Low-Pressure Hot Water (LPHW) heater model. Supplied with terminal box for supply and extract fan motor wiring and for interfacing to custom built control panels Nuaire XBC range of high efficiency heat recovery ventilation units designed for ceiling void applications and are suitable for external use with weather roof. Designed to save energy, improve indoor air quality, and provide the lowest noise breakout when used with Nuaire matched attenuators. Please note that all XBC units are supplied as eft hand units as standard, unless other wise stated on your order. Key Features: High heat exchange efficiency - Up to 95% Low noise Units are aluzinc, asymmetric, high mass, double skinned wall construction with specialist acoustic treatment Compact & flexible - lowest case height (by duty) with unique supply/extract are on unit centreline, intake/extract connections are configurable on site to either side of the unit. Optimum performance – Backward curved impellers and IP54 EC motors provide low specific fan powers and step-less speed control without tonal noise generation. Blowers are ErP 2015 compliant. The unit is designed for side access as standard and must be installed with a minimum of 260mm clearance from a wall or barrier. This will provide access to filters, coil, fan, heat exchanger condensate tray and pump. Technical Features Up to 75% efficient Voltage / Phase / Frequency – 230V / 1 phase / 50 Hz Max operating temperature – 45°C Maximum fan speed (RPM) - 2400 Unit Weight (kg) – 298 Sound level @3m dB(A): 36 – 59 G4 extract and supply filters Counter plate heat exchanger 100% bypass Dimensions (standard model)L x W x D – 1913mm x 1262mm x 405mm Benefits of working with BPC Ventilation Number 1 leading MVHR and ventilation system specialists Large range of systems for domestic and commercial applications

GBP 11769.79
1

Domus AQH200-B Horizontal 204-60 MVHR Unit

Domus AQH200-B Horizontal 204-60 MVHR Unit

Domus AQH200-B Horizontal 204-60 MVHR Unit Product Part Number Domus AQH200-B Horizontal 204-60 MVHR unit - AQH200-B Description The Domus HRX-AQH200-B is a compact and intelligent ceiling mounted unit and with a height of only 200mm it is suitable for narrow service voids The Controllability is provided by an advanced Bluebrain digital controller and optional room sensors or switches We also advise an optional boost switch should be used local to the wet rooms BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 2-year parts warranty* and lifetime technical support on our top-quality systems Filtration 2 x G3 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time) Integral Humidity Sensor The integral humidity sensor incorporated within the extract fan chamber will automatically boost both the extract and supply fan, to the commissioned boost speed, when the humidity level exceeds that set by the Bluebrain Controller. CONTROL OPTIONS The Domus units are controlled by one of the following: Bluebrain controller Humidity sensor Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Bluebrain Control Panel  The controller comes complete with commissioning and end user functions. 75˝ LCD display Current fan speed Current indoor/outside temperature Indicate when the summer bypass is activated Indicate when frost protection is activated Indicate when the filters require cleaning/changing Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Domus units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature  Construction Manufactured of EPP for quietness and efficiency   Mounting The units are ceiling mounted Accessories Condensation Drain – 297 AQH200 Replacement filters - SPR442 8m Data cable – AQHC-CC8

GBP 1447.80
1

Special Offer Panasonic Counter Flow Ventilation VENTX 40V

Special Offer Panasonic Counter Flow Ventilation VENTX 40V

Description PAW-VENTX–V is a ventilation unit complete with a heat recovery exchanger cell which is dedicated to changing air without wasting energy. The unit is particularly suitable for single family units, flats and in all cases where the nominal flow rates for air exchange do not exceed 380 m³/h. The unit is designed for installation inside buildings protected from the weather in a vertical wall position with ducted air distribution. Counter flow ventilation units are equipped with two fans to supply and extract air. A cross-flow heat exchanger recovers the energy contained in the extracted air and transfers it to the supplied air. This significantly reduces the building’s energy consumption, while at the same time keeping a good quality of the indoor air. The PAW-VENTX range is a fixed speed controlled unit, these models are recommended by us for Renovation projects only. Structure: self-supporting sheet metal frame, interior in high density EPS 30 kg/m³ and polyethylene foam. Carpentry and internal plugging in thick galvanised sheet metal. counterflow type: sensible polypropylene version Brushless fans: DC fans regulated by inverters allow high levels of comfort and energy efficiency with constant flow function. Filters: EPM1 filter on fresh air and extract air with low pressure drop. Easily removable for routine maintenance. Models: 2 sizes with different flow rates are available. PAW-VENTX-30V PAW-VENTX-40V Configurations: the unit is configurable in air flows according to the position of the room side and the outdoorside.• A factory configuration• B configuration modifiable on site Vertical Unit Airflow nominal: 266m³/h Airflow Maximum: 380m³/h Dimensions HxWxD: 590 x 576 x 795mm Weight 38kg *Requires Controller* Digital Controller for Panasonic Counter Flow systems(PAW-VENTX) 3 position fixed speed conroller (no accessible adjustment)

GBP 1080.00
1

Special Offer Panasonic Counter Flow Ventilation VENTX 30V

Special Offer Panasonic Counter Flow Ventilation VENTX 30V

Description PAW-VENTX–V is a ventilation unit complete with a heat recovery exchanger cell which is dedicated to changing air without wasting energy. The unit is particularly suitable for single family units, flats and in all cases where the nominal flow rates for air exchange do not exceed 300 m³/h. The unit is designed for installation inside buildings protected from the weather in a vertical wall position with ducted air distribution. Counter flow ventilation units are equipped with two fans to supply and extract air. A cross-flow heat exchanger recovers the energy contained in the extracted air and transfers it to the supplied air. This significantly reduces the building’s energy consumption, while at the same time keeping a good quality of the indoor air. The PAW-VENTX range is a fixed speed controlled unit, these models are recommended by us for Renovation projects only. Structure: self-supporting sheet metal frame, interior in high density EPS 30 kg/m³ and polyethylene foam. Carpentry and internal plugging in thick galvanised sheet metal. counterflow type: sensible polypropylene version Brushless fans: DC fans regulated by inverters allow high levels of comfort and energy efficiency with constant flow function. Filters: EPM1 filter on fresh air and extract air with low pressure drop. Easily removable for routine maintenance. Models: 2 sizes with different flow rates are available. PAW-VENTX-30V PAW-VENTX-40V Configurations: the unit is configurable in air flows according to the position of the room side and the outdoorside.• A factory configuration• B configuration modifiable on site Vertical Unit Airflow nominal: 210m³/h Airflow Maximum: 300m³/h Approximate Property area capacity: 179m2 Dimensions HxWxD: 590 x 576 x 795mm Weight 38kg *Requires Controller* Digital Controller for Panasonic Counter Flow systems(PAW-VENTX) 3 position fixed speed conroller (no accessible adjustment)

GBP 960.00
1

Ebac VA32

Ebac VA32

EBAC VA32 R (Right) EBAC VA32 L (Left) Description The EBAC VA32 is a quality Uk manufactured MVHR unit with good controllability and provides a maximum flow rate of 245m3/hr suitable for a house up to 150 m2 floor area with up to 3 kitchens & bathrooms Controllability is provided by a digital touch screen controller that comes complete with the unit and has internal humidity & Co2 sensors for demand-controlled ventilation BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems, KEY FEATURES – EBAC VA32 Digital Touch Screen controller Smart control option Suitable for floor areas up to 172m2 Delivers an airflow rate of up to 288 m³/hour @ 100 Pa High heat recovery efficiency of up to 88%. Internal humidity sensor for automatic speed control Internal Co2 and temperature sensors On demand control via optional room or duct sensor options Full 100% automatic summer bypass to supply unheated air in the summer 2 x G4 filters Galvanised steel casing with 32mm thermal insulation 5-year warranty* (Listed parts Only) 'A' energy rating Left hand right oriented models available Adjustable feet Sap Appendix Q (BRE) approved UK/CA marked Surge protected Integral Humidity Sensor The EBAC unit has an Internal Humidity sensor that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace CONTROL OPTIONS The EBAC units are controlled by one of the following: Digital touchscreen Controller On-demand ventilation through built-in humidity & Co2 sensors Switched live signal from light / remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 88% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The EBAC units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The EBAC VA32 units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of double skin powder coated galvanised steel with a 32mm thermal insulation Mounting The units are wall mounted as standard and are supplied with a wall bracket If floor mounting it is recommended to elevate the unit by 150mm to allow access to the condensation drain The four feet are adjustable to allow for any uneven surface Accessories EBAC VA32 Replacement filters - VA32-G4FILTER

GBP 1200.00
1

Mitsubishi Lossnay-VL250 Units

Mitsubishi Lossnay-VL250 Units

Mitsubishi Lossnay-VL Units Product Part Number Mitsubishi Lossnay VL-250 (L) wall mounted residential MVHR with bypass and digital controller - LEFT - VL-250CZPVU-L-E Mitsubishi Lossnay VL-250 (R) wall mounted residential MVHR with bypass and digital controller - RIGHT - VL-250CZPVU-R-E Description The Mitsubishi VL-250 is a quality unit with the advantage of a unit mounted controller with 5 years part warranty and provides a maximum flow rate of 250m3/hr suitable for a house up to 150 m2 floor area with up to 3 kitchens & bathrooms BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems Filtration 2 x G3 filters are fitted to the unit that are easy and inexpensive to replace Optional ePM2.5 50% to air supply Optional NOX 90% filter to air supply CONTROL OPTIONS The Mitsubishi VL units are controlled by one of the following: Control Via Unit mounted digital controller 0-10v sensor Volt free contacts Additional external sensors achieving on-demand ventilation Switched live signal from remote switches Optional wall controller (P-RCC-E) Optional Wi-Fi integration to phone (MAC-5671F-E)   Optional Wi-Fi with additional accessory - MAC-5617F-E   Summer By-Pass The VL range of units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit   Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-3°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Orientation The Mitsubishi Lossnay VL units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The units are wall mounted as standard and are supplied with a wall bracket

GBP 1001.45
1

Nuaire - AB-WM1 MRXBOX95 Unit

Nuaire - AB-WM1 MRXBOX95 Unit

Nuaire MRXBOXAB-WM1 Opposite Handed MRXBOXAB-WM1-OH Description The Nuaire MRXBOXAB-WM1 provides a maximum flow rate of 125m3/hr suitable for a house up to 73m2 floor area with up to 2 kitchens & bathrooms(no digital controller or humidity sensor is available for this model)The Nuaire MRXBOX range has been in continual improvement and production in the UK for over 15years providing a high performance, wall-mounted MVHR unit which is specifically designed to provide areliable but simple to operate system for social housing, developments and end usersBPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-yearparts warranty* and lifetime technical support on our top-quality systems Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace(The filters are provided with plastic covers that should be removed before starting unit for first time) CONTROL OPTIONS The Nuaire MRXBOX units are controlled by one of the following:We also advise an optional boost switch should be used local to the wet rooms 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 86% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Nuaire AB units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The Nuaire units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The Nuaire units are wall mounted as standard and are supplied with a wall bracket    

GBP 971.28
1

Mitsubishi Lossnay-VL500 Units

Mitsubishi Lossnay-VL500 Units

Mitsubishi Lossnay-VL Units Product Part Number Mitsubishi Lossnay VL-500 (L) wall mounted residential MVHR with bypass and digital controller - LEFT - VL-500CZPVU-L-E Mitsubishi Lossnay VL-500 (R) wall mounted residential MVHR with bypass and digital controller - RIGHT - VL-500CZPVU-R-E Description The Mitsubishi VL-500 is a quality unit with the advantage of a unit mounted controller with 5 years part warranty and provides a maximum flow rate of 540m3/hr suitable for a house up to 320 m2 floor area with up to 6 kitchens & bathrooms BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems Filtration 2 x G3 filters are fitted to the unit that are easy and inexpensive to replace Optional ePM2.5 50% to air supply Optional NOX 90% filter to air supply CONTROL OPTIONS The Mitsubishi VL units are controlled by one of the following: Control Via Unit mounted digital controller 0-10v sensor Volt free contacts Additional external sensors achieving on-demand ventilation Switched live signal from remote switches Optional wall controller (P-RCC-E) Optional Wi-Fi integration to phone (MAC-5671F-E) Optional Wi-Fi with additional accessory - MAC-5617F-E Summer By-Pass The VL range of units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-3°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Orientation The Mitsubishi Lossnay VL units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The units are wall mounted as standard and are supplied with a wall bracket  

GBP 1319.45
1

Domus HRX-E AURA Heat Recovery Unit

Domus HRX-E AURA Heat Recovery Unit

Domus HRXE-AURA-H Opposite Handed - HRXE-AURA-OPH   Description The Domus HRXE-AURA-H provides a maximum flow rate of 320m3/hr suitable for a house up to 190 m2 floor area with up to 5 kitchens & bathrooms Controllability is provided by an internal humidity sensors and optional room sensors or switches (no digital controller is available for this model) BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems Integral Humidity Sensor The Domus unit has an Internal Humidity sensor that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G3 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time) CONTROL OPTIONS The Domus units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Domus units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The Domus units can be right or left-handed and correct orientation should be checked before purchase  Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The units are wall mounted as standard and are supplied with a wall bracket AV (anti vibration mounting kit) - HRXE-AURA-AV  The optional anti vibration kit can be used for both wall and floor Tank Stand The MVHR unit can be positioned on the optional tank stand using the Anti-vibration tray assembly discarding the angle brackets. (7) Angled Brackets The unit can be installed above the floor on a wall angled bracket (8) Accessories Condensation Drain – 397 Aura Replacement filters SPR428  

GBP 1480.66
1

Domus HRXE-ZEUS

Domus HRXE-ZEUS

Domus HRXE-ZEUS Product Part Number Domus HRXE-ZEUS-H Opposite Handed - HRXE-ZEUS-OPH Description The Domus HRXE-ZEUS-H provides a maximum flow rate of 550m3/hr suitable for a house up to 330 m2 floor area with up to 10 kitchens & bathrooms Controllability is provided by an internal humidity sensors and optional room sensors or switches (no digital controller is available for this model) BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems Integral Humidity Sensor The Domus unit has an Internal Humidity sensor that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G3 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time) CONTROL OPTIONS The Domus units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Domus units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The Domus units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The units are wall mounted as standard and are supplied with a wall bracket AV (anti vibration mounting kit) - HRXE-XEUS-AV The optional anti vibration kit can be used for both wall and floor Tank Stand The MVHR unit can be positioned on the optional tank stand using the Anti-vibration tray assembly discarding the angle brackets. (7) Angled Brackets The unit can be installed above the floor on a wall angled bracket (8) Accessories Condensation Drain – 297 ZEUS Replacement filters SPR459  

GBP 2935.30
1

Nuaire AB-ECO-LP2 Ceiling Void Horizontal MVHR Unit

Nuaire AB-ECO-LP2 Ceiling Void Horizontal MVHR Unit

Nuaire ceiling void unit - ECO-LP2 Nuaire ceiling void unit Opposite hand - ECO-LP2-OH Description The new MRXBOXAB-ECO-LP2 is a Low-Profile ceiling mounted unit that is specificallydesigned to fit easily into apartments with ceiling void restrictions of only 200mm and has a high performance of 285m3/hr with low SFP of 0.56 wls Controllability is provided by optional room sensors or switches (no digital controller is available for this model) The Nuaire MRXBOX range has been in continual improvement and production in the UK for over 15 years providing a high performance, wall-mounted MVHR unit which is specifically designed to provide a reliable but simple to operate system for social housing, developments and end users BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems, KEY FEATURES – Nuaire AB-ECO-LP2 Suitable for floor areas up to 170m2 Delivers an airflow rate of up to 285 m³/hour @ 100 Pa High heat recovery efficiency of up to 79%. 100% summer by-pass On demand control via optional room or duct sensor options Full 100% automatic summer bypass to supply unheated air in the summer Sap Appendix Q (BRE) approved 2 x G3 filters Galvanised steel casing with EPP internal lining 2-year warranty* (Listed parts Only) 'A' energy rating Left hand right oriented models available UK/CA marked Surge protected Filtration 2 x G3 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time) CONTROL OPTIONS The Nuaire MRXBOX units are controlled by one of the following: Manual 100% adjustment of background and boost speeds 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Nuaire AB units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The Nuaire units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency

GBP 1692.20
1

Domus HRX-E HERA Heat Recovery Unit

Domus HRX-E HERA Heat Recovery Unit

Domus HRX-E HERA Heat Recovery Unit Product Part Number Domus HRXE-HERA-H Opposite Handed - HRXE-HERA-OPH Description The Domus HRXE-HERA-H provides a maximum flow rate of 288m3/hr suitable for a house up to 172 m2 floor area with up to 5 kitchens & bathrooms Controllability is provided by an internal humidity sensors and optional room sensors or switches (no digital controller is available for this model) BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems, Integral Humidity Sensor The Domus unit has an Internal Humidity sensor that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G3 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time) CONTROL OPTIONS The Domus units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Domus units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The Domus units can be right or left-handed and correct orientation should be checked before purchase  Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The units are wall mounted as standard and are supplied with a wall bracket AV (anti vibration mounting kit) - HRXE-HERA-AV The optional anti vibration kit can be used for both wall and floor Tank Stand The MVHR unit can be positioned on the optional tank stand using the Anti-vibration tray assembly discarding the angle brackets. (7) Angled Brackets The unit can be installed above the floor on a wall angled bracket (8) Accessories Condensation Drain – 297 HEAR Replacement filters SPR428  

GBP 1270.67
1

Nuaire MRXBOXAB-ECO2-1Z with Accoustic Enclosure & Silent Box

Nuaire MRXBOXAB-ECO2-1Z with Accoustic Enclosure & Silent Box

Nuaire MRXBOXAB-ECO2B-1Z Opposite Handed MRXBOXAB-ECO2B-1Z-OH   Description The Nuaire MRXBOXAB-ECO2B-1Z consists of the ECO2 MVHR unit, attenuators and flexible duct connectors entirely encased in an all-in-one aesthetically pleasing acoustic enclosure This kit provides significant reduction in cased-radiated noise The ECO2B-1Z provides a maximum flow rate of 288m3/hr suitable for a house up to 172 m2 floor area with up to 5 kitchens & bathrooms Controllability is provided by an internal humidity sensors and optional room sensors or switches (no digital controller is available for this model) The Nuaire MRXBOX range has been in continual improvement and production in the UK for over 15 years providing a high performance, wall-mounted MVHR unit which is specifically designed to provide a reliable but simple to operate system for social housing, developments and end users BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems Acoustic Enclosure MRXBOXAB-ECO2B-1Z - The 1Z is the all-in-one acoustic enclosure, allowing in the MVHR unit and attenuator to be entirely cased in an aesthetically pleasing model which encloses the attenuators and flexible duct connections that would otherwise be visible, all whilst making significant reduction in cased-radiated noise. Integral Humidity Sensor The Nuaire unit has a internal humidity sensors that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time) CONTROL OPTIONS The Nuaire MRXBOX units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time)  CONTROL OPTIONS The Nuaire MRXBOX units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Nuaire AB units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The Nuaire units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for

GBP 2653.26
1

Nuaire MRXBOXAB-ECO4-1Z With Acoustic & Silent Box

Nuaire MRXBOXAB-ECO4-1Z With Acoustic & Silent Box

Description Nuaire MRXBOXAB-ECO4B-1Z Opposite Handed MRXBOXAB-ECO4B-1Z-OH The Nuaire MRXBOXAB-ECO4B-1Z consists of the ECO4 MVHR unit, attenuators and flexible duct connectors entirely encased in an all-in-one aesthetically pleasing acoustic enclosure This kit provides significant reduction in cased-radiated noise The Nuaire MRXBOXAB-ECO4B provides a maximum flow rate of 555m3/hr suitable for a house up to 330 m2 floor area with up to 10 kitchens & bathrooms Controllability is provided by an internal humidity sensors and optional room sensors or switches (no digital controller is available for this model) The Nuaire MRXBOX range has been in continual improvement and production in the UK for over 15 years providing a high performance, wall-mounted MVHR unit which is specifically designed to provide a reliable but simple to operate system for social housing, developments and end users BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems, KEY FEATURES – Nuaire AB-ECO4B Acoustic enclosure on unit and Attenuator top box Attenuators and flexible duct connectors Suitable for floor areas up to 330m2 Delivers an airflow rate of up to 555 m³/hour @ 100 Pa High heat recovery efficiency of up to 94%. Internal humidity sensor for automatic speed control 100% summer by-pass On demand control via optional room or duct sensor options Full 100% automatic summer bypass to supply unheated air in the summer Sap Appendix Q (BRE) approved 2 x G4 filters Galvanised steel casing with EPP internal lining 2-year warranty* (Listed parts Only) 'A' energy rating Left hand right oriented models available UK/CA marked Surge protected Integral Humidity Sensor The Nuaire unit has a internal humidity sensors that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time) CONTROL OPTIONS The Nuaire MRXBOX units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Nuaire AB units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The Nuaire units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The Nuaire units are wall mounted as standard and are supplied with a wall bracket

GBP 5063.84
1

Nuaire MRXBOXAB-ECO3-1Z with Accoustic Enclosure & Silent Box

Nuaire MRXBOXAB-ECO3-1Z with Accoustic Enclosure & Silent Box

Description Nuaire MRXBOXAB-ECO3-1Z Opposite Handed MRXBOXAB-ECO3-1Z-OH The Nuaire MRXBOXAB-ECO3-1Z consists of the ECO3 MVHR unit, attenuators and flexible duct connectors entirely encased in an all-in-one aesthetically pleasing acoustic enclosure This kit provides significant reduction in cased-radiated noise The Nuaire MRXBOXAB-ECO3B provides a maximum flow rate of 320m3/hr suitable for a house up to 190 m2 floor area with up to 6 kitchens & bathrooms Controllability is provided by an internal humidity sensors and optional room sensors or switches (no digital controller is available for this model) The Nuaire MRXBOX95 range has been in continual improvement and production in the UK for over 15 years providing a high performance, wall-mounted MVHR unit which is specifically designed to provide a reliable but simple to operate system for social housing, developments and end users BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems, KEY FEATURES – Nuaire AB-ECO3 Acoustic enclosure on unit and Attenuator top box Attenuators and flexible duct connectors Suitable for floor areas up to 190m2 Delivers an airflow rate of up to 320 m³/hour @ 100 Pa High heat recovery efficiency of up to 90%. Internal humidity sensor for automatic speed control 100% summer by-pass On demand control via optional room or duct sensor options Full 100% automatic summer bypass to supply unheated air in the summer Sap Appendix Q (BRE) approved 2 x G4 filters Galvanised steel casing with EPP internal lining 2-year warranty* (Listed parts Only) 'A' energy rating Left hand right oriented models available UK/CA marked Surge protected Integral Humidity Sensor The Nuaire unit has a internal humidity sensors that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time) CONTROL OPTIONS The Nuaire MRXBOX units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time)  CONTROL OPTIONS The Nuaire MRXBOX units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The Nuaire AB units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature

GBP 2960.52
1

Mitsubishi Lossnay-VL350 Units

Mitsubishi Lossnay-VL350 Units

Part Numbers Mitsubishi VL-350CZPVU-L-E (Left hand) Mitsubishi VL-350CZPVU-R-E (Right hand) Description The Mitsubishi VL-350 is a quality unit with the advantage of a unit mounted controller with 5 years part warranty and provides a maximum flow rate of 350m3/hr suitable for a house up to 210 m2 floor area with up to 6 kitchens & bathrooms BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems, KEY FEATURES – Mitsubishi VL-350 Suitable for floor areas up to 210m2 Delivers an airflow rate of up to 350 m³/hour @ 150 Pa Unit mounted LCD controller Ultra quiet with as low as 15dB High heat recovery efficiency of up to 90%. On demand control via optional room or duct sensor options Full 100% automatic summer bypass to supply unheated air in the summer Sap Appendix Q (BRE) approved 2 x G3 filters Galvanised steel casing with EPP internal lining 5-year warranty* (Listed parts Only) 'A+' energy rating Left hand right oriented models available Optional Wi-Fi control UK/CA marked Surge protected Filtration 2 x G3 filters are fitted to the unit that are easy and inexpensive to replace Optional ePM2.5 50% to air supply Optional NOX 90% filter to air supply CONTROL OPTIONS The Mitsubishi VL units are controlled by one of the following: Control Via Unit mounted digital controller 0-10v sensor Volt free contacts Additional external sensors achieving on-demand ventilation Switched live signal from remote switches Optional wall controller (P-RCC-E) Optional Wi-Fi integration to phone (MAC-5671F-E) Optional Wi-Fi with additional accessory - MAC-5617F-E   Summer By-Pass The VL range of units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-3°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Orientation The Mitsubishi Lossnay VL units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The units are wall mounted as standard and are supplied with a wall bracket

GBP 1202.95
1

BSK Plus 40 Commercial Heat Recovery Unit

BSK Plus 40 Commercial Heat Recovery Unit

BSK Plus 40 Commercial Heat Recovery Unit Product Part Number BSK 4000 m3h/r Horizontal MVHR - digital control - 400mm - BRHR Plus 40 BSK 4000 m3h/r Horizontal MVHR - digital control - 400mm - 10kw pre heater - BRHR Plus 40+pre heater BSK 4000 m3h/r Horizontal MVHR - digital control - 400mm - 23kw post heater - BRHR Plus 40+post heater BSK 4000 m3h/r Horizontal MVHR - digital control - 400mm - 23kw water heater - BRHR Plus 40+water heater Key Features Self-motorized EC fans Provides up to 90% heat recovery Plug and play electrical connections Bypass damper for free cooling Highly efficient aluminium heat exchanger Thin, flat profile is perfect for ceiling mounting ModBus compatible EC fans with lower power consumptions Weight - 366 kg Technical Features Airflow capacity - 4000m3h/r @ 150Pa 2 x G4 filters with side panel allowing easy access for maintenance H x W x D: 667mm x 1650mm x 1850mm 400mm duct connections BSK Plus Commercial Heat Recovery units are available with a preheater, post heater or a water heater Boost mode allows the unit to run at full capacity in order to quickly ventilate the surroundings Boost mode can be triggered in different ways via the built-in humidity sensor or via an external switch Control Options Free cooling Boost mode De-frost mode Automated weekly schedules Temperature or humidity trigged automation Free Cooling Mode During seasonal transitions for example, Spring and Autumn, when indoor and outdoor temperature difference are not signification, the unit automatically switch to Free Cooling Mode by opening the built-in bypass vent. The air will pass through this canal without going through the heat exchanger, thus reducing the stress on fans and operate on an even less power. This set temperature can be changed on the digital control panel to a desired level. Defrost Mode We suggest that you equip a pre-heater for

GBP 8856.68
1

Nuaire MRXBOXAB-ECO2 Heat Recovery System

Nuaire MRXBOXAB-ECO2 Heat Recovery System

Nuaire MRXBOXAB-ECO2B Opposite Handed MRXBOXAB-ECO2B-OH Description The Nuaire MRXBOXAB-ECO2B provides a maximum flow rate of 288m3/hr suitable for a house up to 172 m2 floor area with up to 5 kitchens & bathrooms Controllability is provided by an internal humidity sensors and optional room sensors or switches (no digital controller is available for this model) The Nuaire MRXBOX range has been in continual improvement and production in the UK for over 15 years providing a high performance, wall-mounted MVHR unit which is specifically designed to provide a reliable but simple to operate system for social housing, developments and end users BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems Integral Humidity Sensor The Nuaire unit has a internal humidity sensors that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace (The filters are provided with plastic covers that should be removed before starting unit for first time)  CONTROL OPTIONS The Nuaire MRXBOX units are controlled by one of the following: 4 x adjustable switches on the front of the unit Manual control Via optional 3 speed manual switch On-demand ventilation through built-in humidity sensors Additional external sensors achieving on-demand ventilation Switched live signal from light/remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 90% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time.   Summer By-Pass The Nuaire AB units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The Nuaire units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of powder coated galvanised steel outer cover for durability and an inside EPP lining for quietness and efficiency Mounting The Nuaire units are wall mounted as standard and are supplied with a wall bracket An optional angled mounting bracket MRXBOX-AV2 are fitted to the bottom of the unit are available First Fix Solution MRXBOX-FF2 Nuair’s First Fix box is fixed to the underside of the floor slab at first fix stage of the build. The box has four airflow chambers with optional positions for 204x60mm spigots. Ceilings can then be boarded within the cupboard space easily and quickly without the risk of the spigots not aligning to the fan unit. Acoustic Enclosure Optional acoustic solutions are available for high demanding properties requiring the quietest system possible MRXBOXAB-ECO2B-AE – Unit has an acoustic surrounding with internal anti vibration mounts to the MVHR unit and flexible duct connectors MRXBOXAB-ECO2B-1Z - The 1Z is the all-in-one acoustic enclosure, allowing in the MVHR unit and attenuator to be entirely cased in an

GBP 1123.50
1