14 results (0,13651 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Vesda Xtralis M8 Nut - Pack of 10 PIP-029

Vesda Xtralis M8 Nut - Pack of 10 PIP-029

Vesda Xtralis M8 Nut - Pack of 10 PIP-029M8 Nut for fitting clip to the end of threaded rod.VESDA Aspirating Pipe and Fittings are produced in red ABS under a stringent quality control system approved to BS EN ISO 9001 EN54 - 20 and EN61386-1 Class 1131 ABS Acrylonitrile Butadiene Styrene is a robust polymer which has the most suitable physical properties for aspirating detection optimising performance with tensile strength chemical resistance ductility weatherability heat stability and processability.The range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system. They are also manufactured to comply with the requirements of BS5391 Part 1 EN 61386-1 and the new EN54 Part 20 guaranteeing you the quality you are used to as a VESDA customer.Please Note The PIP-029 is equivalent to the ACCPCN025B.

GBP 7.37
1

Kantech P40KEY Tag

Kantech P40KEY Tag

Kantech P40KEY TagsThe P40KEY fits conveniently to your keys or to a badge reel lanyard or chain. The Kantech ioProx proximity card is compatible with all ioProx readers and ioPass stand-alone systems. The cards come pre-programmed all you need to do is enrol them onto your system. There are zero compatibility issues if your existing cards key tags or readers have the ioProx logo then these are compatible.Key FeaturesFob tagTechnology Type ProximityMaterial ABS shell epoxy pottedPhysical Specifications Dimensions mm 50 x 20 x 5Weight 5gOperating Temp oC -45 70DurableResistant to cracking and breaking

GBP 6.40
1

Hochiki MBB-2WHT White Marine Mounting Back Box with Glands

Hochiki MBB-2WHT White Marine Mounting Back Box with Glands

Hochiki MBB-2WHT White Marine Mounting Back Box with GlandsThe approved design of the MBB-2 provides a splash-proof secure fixing for the Hochiki CDX and ESP Marine Approved Range of Detectors and their associated Bases. It can be installed on a variety of different fixing surfaces and because it has been manufactured to match the colour of Hochikis range of products it provides an aesthetically pleasing solution where surface fixed devices are required.The housing supports four 20 mm glanded entries for zone or loop cabling access. It is also supplied with base fixing screws and two cable glands specifically designed to provide protection against water ingress.The detector base fits directly onto the MBB-2 and sits within a slight recess. This provides the accurate fit and the protection against dust and water ingress. The MBB-1 is also the recommended choice of back box for Hochikis Waterproof Heat Detectors the DFG-60E and the ACB-EW.Key Features4 cable entry holes suitable for cable glands 2 glands suppliedColour matched to both ivory and white detector rangesApproved Sensor and Base rangeProvides moisture and dust resistant fixingIdeal for bulk-head fixingApproved by LR and GLNon-marine use version available SBB-2

GBP 5.54
1

Vesda Xtralis PIP-027 Air Sampling Test Point with Cap

Vesda Xtralis PIP-027 Air Sampling Test Point with Cap

Vesda XtralisPIP-027Air Sampling Test Point with CapThey are designed to measure the transportation time a small quantity of smoke is introduced at the furthest point and the measurement in time is calculated from when the smoke enters the sampling point to when the ASD reacts. The maximum transport time is 120 seconds 2 minutes. Test points are the ideal solution for flexibility and convenience. They are installed at the end of the pipe run however for areas such as a lift shaft where accessibility is limited the pipe run can be brought into a riser.A key element of the VESDA system is its suction system which actively transports air from the protected area to the detector.The test point is for periodic smoke testing of the VESDA system for hard to reach areas.VESDA installations can be designed for the most complex areas using carefully selected shaped elements.The use of these shaped elements has a positive effect on the pneumatic system of the installation which translates into the unique and legendary quality of the VESDA system work in each pneumatic system.The suction installation is calculated with theASPIREprogramme.The program is used for modelling and visualization of aspiration installations class calculation in accordance with PN-EN-54-20.Please note The PIP-027 is equivalent to the REDAST025C.

GBP 7.49
1

Kentec Line Continuity Monitoring Unit K14060

Kentec Line Continuity Monitoring Unit K14060

Kentec LCMU Line Continuity Monitoring Unit K14060To use this method of monitoring the breaking connection of the detector base must be fitted with a diode. To ensure correct operation over a wide supply voltage range and with up to 20 detectors removed a Schottky type BYV-1060 is recommended. These devices are however very sensitive to electrostatic discharge and extra care should be taken when handling or cable testing. It is also necessary to fit a 47uF capacitor to the detection line terminals on some of the control panels not K3000 series or Sigma CP.Extreme care should be taken when fitting the capacitor in the panel as they are polarity conscious. The LCMU itself is also polarity conscious and the polarity is indicated in the normal manner i.e. black wire is always negative. A wrongly connected LCMU will produce a short circuit fault condition. Due to the use of surface mount technology components the LCMU is probably the smallest device of its kind on the market. This enables the device to be fitted either within the last device on a zone or in the back box eliminating the need for an additional wiring point.Key FeaturesEasy to installNo additional wiring pointLow costSub-miniature designEnvironmentally sealed

GBP 8.56
1

Hochiki MBB-2 Ivory Marine Mounting Back Box with Glands

Hochiki MBB-2 Ivory Marine Mounting Back Box with Glands

Hochiki MBB-2 Ivory Marine Mounting Back Box with GlandsThe approved design of the MBB-2 provides a splash-proof secure fixing for the Hochiki CDX and ESP Marine Approved Range of Detectors and their associated Bases. It can be installed on a variety of different fixing surfaces and because it has been manufactured to match the colour of Hochikis range of products it provides an aesthetically pleasing solution where surface fixed devices are required.The housing supports four 20 mm glanded entries for zone or loop cabling access. It is also supplied with base fixing screws and two cable glands specifically designed to provide protection against water ingress. The detector base fits directly onto the MBB-2 and sits within a slight recess. This provides the accurate fit and the protection against dust and water ingress. The MBB-1 is also the recommended choice of back box for Hochikis Waterproof Heat Detectors the DFG-60E and the ACB-EW.Key Features4 cable entry holes suitable for cable glands 2 glands suppliedColour matched to both ivory and white detector rangesApproved Sensor and Base rangeProvides moisture and dust resistant fixingIdeal for bulk-head fixingApproved by LR and GLNon-marine use version available SBB-2

GBP 5.54
1