17 results (0,15017 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Commander HR6 25mm Swinging Manual Hose Reel

Commander HR6 25mm Swinging Manual Hose Reel

CommanderHR625mm Swinging Manual Hose ReelThe purpose of Hose Reels is to provide a reasonably accessible and controlled supply of water to combat a potential fire risk. The nozzle attached to the end of the hose enables the operator to control the direction and flow of water to the fire.The HR6 is a 25mm swinging manual hose reel designed to be slimline best suited for corridors or passageways. The hose reel is polyester coated steel side plated for high corrosion protection. The hose reel comes with an impact resistant nozzle.Hose Reel Used ForClass A Fires Wood paper textiles and other carbonaceous materialsKey FeaturesComplete with 30m hose ready to installKitemarked to BS EN671-1Robust all-metal construction powder coated finishEasy to install and maintain

GBP 429.43
1

Commander HR2 25mm Fixed Manual Hose Reel

Commander HR2 25mm Fixed Manual Hose Reel

CommanderHR225mm Fixed Manual Hose ReelThe purpose of Hose Reels is to provide a reasonably accessible and controlled supply of water to combat a potential fire risk. The nozzle attached to the end of the hose enables the operator to control the direction and flow of water to the fire.The HR2 is a 25mm fixed manual hose reel designed to be slim line best suited for corridors or passageways. The hose reel is polyester coated steel side plated for high corrosion protection. The hose reel comes with an impact resistant nozzle.Hose Reel Used ForClass A Fires Wood paper textiles and other carbonaceous materialsKey FeaturesComplete with 30m hose ready to installKitemarked to BS EN671-1Robust all-metal construction powder coated finishEasy to install and maintain

GBP 438.04
1

Patol FBS 25 Small Filter Box 25mm PC 50-0500143-01-02P

Patol FBS 25 Small Filter Box 25mm PC 50-0500143-01-02P

Patol FBS 25 Small Filter Box 25mm PC 50-0500143-01-02PThe filter box small is used as an accessory part for aspirating smoke detectors in areas with low temperature conditions below 0C and high dust levels to prevent false alarms and to increase the lifespan of the smoke sensors substantially.The filter insert is designed for the separation of particles and impurities. Due their particle size smoke particles can pass through this filter unhindered. Reliable and fast fire detection is thus ensured.The air polluted with dust particles is also aspirated by the aspirating smoke detector. To prevent false alarms the aspirated air must be purified of these particles. The filter box small can be used for this purpose as an additional accessory component.Key FeaturesPrevention or substantial reduction of false alarmsLengthening of lifespan of smoke sensorsVery low installation costsSubsequent installation possible at any timeLow operating costsApplicable for all aspirating smoke detectorsQuick clean and inexpensive solutionField of application deep freeze areaPipe Connection Diameter 25mmMaterial PC

GBP 184.38
1

SAS Caring Technology Touch-Display-Network-SF Vandal Resistant Display and Sounder

SAS Caring Technology Touch-Display-Network-SF Vandal Resistant Display and Sounder

SAS Caring Technology Touch-Display-Network-SF Vandal Resistant Display and SounderDesigned for challenging environments. The displaysounder unit manufactured from 4mm Makrolon polycarbonate is low profile and vandal resistant. The display clearly shows the exact location of an incident whilst drawing their attention audibly with a grille less speaker. Each call level has its own unique sound and if multiple calls are on the system the scroll buttons can be used to navigate through the list. The display unit features touch buttons only with a function to disable the buttons for ten seconds for cleaning. The back box is 25mm deep and for flush mounting installations employs a shock absorbing spring loaded caddy that allows 8mm of play to assist with the mounting of the device. Included 4 x torx M3.5 x 25mm security screws.Key FeaturesMaterial Polycarbonate MakrolonFascia 195mm x 115mm x 4mm surface or 225mm x 145mm x 4mm flushBack box 200mm x 120mm x 25mmDisplay window 145mm x 35mmCharacter height 12mmWeight with back box 400g 230gSupply current 20mA inactive 160mA activeSpeaker volume 60dbNetwork R B and YTemperature 0-50C

GBP 324.00
1

Kidde Airsense Stratos Pipe Stand-off Support 9-10936

Kidde Airsense Stratos Pipe Stand-off Support 9-10936

Kidde Airsense Stratos Pipe Stand-off Support9-10936The pipe stand-off support includes CLIC TOP 28 pipe clip M8 x 60mm stud and mounting bracket. The stand-off is suitable for 34 pipework and not suitable for 25mm pipework.Aspirating smoke detection system is the network of sampling pipes that actively transport air from a protected area to the detector. ABS Acrylonitrile Butadiene Styrene is a homogenous material with good chemical resistance and high impact strength. Other beneficial features are its suitability for use at low temperatures -40C and its ease of joining.

GBP 365.78
1

C-Tec NC944SS Four Zone Call Controller in Stainless Steel

C-Tec NC944SS Four Zone Call Controller in Stainless Steel

C-Tec NC944SS Four Zone Call Controller in Stainless SteelThe NC944SS is an attractively-designed four zone call controller which comes with mute and reset buttons.Key FeaturesFully compatible with C-TECs entire range of 800 Series Call System componentsCapable of indicating standard constant tone and emergency intermittent tone callsRequires a separate NC930 12V 250mA PSUIncludes four zonal alarm LEDs RESET and MUTE buttonsTwo open collector outputs Emergency and Aux OutUp to two NC944s can be connected to one NC930 PSU to create a mini-call system of up to 8 zonesMounts on a standard 25mm UK double gang back boxPlease note The image is for illustrative purposes only

GBP 235.82
1

SAS Caring Technology Touch-Curo-Key-DM Touch Curo Key for Door Monitor - With ArmDisarm Functions

SAS Caring Technology Touch-Curo-Key-DM Touch Curo Key for Door Monitor - With ArmDisarm Functions

SAS Caring Technology Touch-Curo-Key-DM Touch Curo Key for Door Monitor - With ArmDisarm FunctionsDesigned for challenging environments. The staff reset unit manufactured from injection molded Tritan Tx more resilient than Polycarbonate is low profile and vandal resistant. The staff reset unit is situated near a monitored door at hip height and. Under normal operation if the door is opened the SRU triggers an elevated call ALARM it is then reset by the Curo at very close range. Touching the Curo on the depicted graphic will reset the alarm. The SRU can be dis-armed to ignore the door state by manually touching the Curo on the graphic this mode is commonly used through the day. The LED will acknowledge with a brief white colour followed by a blue flash. To return the SRU to normal operation touch the Curo on the graphic there will be a white acknowledge followed by a red flash. Whenever the SRU is set there will be a brief period where the door state will be ignored this is engineer adjustable and if set to zero there will be no delay to ARMED. During the delay to arm a relay output closes which could be used as an electronic lock release. Note there is no means to reset device by emergency services so a break-glass unit must be used. The staff reset unit is addressable and its 20-character name is programmed by infrared only. Available with an optional buzzer if greater audibility is needed. Included 2x torx M3.5 x 25mm security screws. Note Curo refers to the staff alarm fob personal alarm transmitter.Key FeaturesFascia 95mm x 95mm x 5.4mmBack box Single gang depth 25mm recommendedLED RGBWeight with back box 78g 250gSupply current 2.5mA inactive 38mA activeNetwork R B and YTemperature 0-50C

GBP 186.30
1

SAS Caring Technology Touch-Curo-Key-RU Touch Curo Key for Room Unit

SAS Caring Technology Touch-Curo-Key-RU Touch Curo Key for Room Unit

SAS Caring Technology Touch-Curo-Key-RU Touch Curo Key for Room UnitDesigned for challenging environments. The staff reset unit manufactured from injection molded Tritan Tx more resilient than Polycarbonate is low profile and vandal resistant. The staff reset unit is situated near a monitored door at hip height and. Under normal operation if the door is opened the SRU triggers an elevated call ALARM it is then reset by the Curo at very close range.Touching the Curo on the depicted graphic will reset the alarm. The SRU can be dis-armed to ignore the door state by manually touching the Curo on the graphic this mode is commonly used through the day. The LED will acknowledge with a brief white colour followed by a blue flash. To return the SRU to normal operation touch the Curo on the graphic there will be a white acknowledge followed by a red flash. Whenever the SRU is set there will be a brief period where the door state will be ignored this is engineer adjustable and if set to zero there will be no delay to ARMED. During the delay to arm a relay output closes which could be used as an electronic lock release. Note there is no means to reset device by emergency services so a break-glass unit must be used. The staff reset unit is addressable and its 20-character name is programmed by infrared only.Available with an optional buzzer if greater audibility is needed. Included 2x torx M3.5 x 25mm security screws. Note Curo refers to the staff alarm fob personal alarm transmitter.Key FeaturesFascia 95mm x 95mm x 5.4mmBack box Single gang depth 25mm recommendedLED RGBWeight with back box 78g 250gSupply current 2.5mA inactive 38mA activeNetwork R B and YTemperature 0-50C

GBP 186.30
1

Lexicomm ViLX-ACR Touchscreen Assist Call Repeater

Lexicomm ViLX-ACR Touchscreen Assist Call Repeater

Lexicomm ViLX-ACR Touchscreen Assist Call RepeaterA compact 2.8 touchscreen mounted in a double gang MK style plate to indicate assist calls ideal for mounting in a desk or on the wall in a reception.The Lexicomm ViLX-ACR provides remote indication of Assist Call alarms and provides an acknowledgment facility. It is ideal for mounting within a reception desk or on a wall due to its compact size and pleasing aesthetics.It connects to the Lexicomm network via the nearest ViLX-EX8 System Expander panel via Cat 5 cable plugging in to a dedicated port. It can be located up to 30m away and does not require a power supply and does not take a line output.It has a brushed stainless-steel finish 2.8 high contrast full colour touch screen display. Sized at 146mm x 86mm it mounts onto 25mm deep standard double gang electrical box.Key Features2.8 TFT touch screen colour displayHigh volume sounder with volume controlConnects to Lexicomm System ExpandersAesthetically pleasing stainless finishNo local power requiredCan be Located up to 30m from the expander using Cat 5 Cable

GBP 355.84
1

SAS Caring Technology Touch-Wireless-CP Touch Wireless Call Point with Call Level No Reset

SAS Caring Technology Touch-Wireless-CP Touch Wireless Call Point with Call Level No Reset

SAS Caring Technology Touch-Wireless-CP Touch Wireless Call Point with CallLevel No ResetDesigned for challenging environments. The room unitmanufactured from injection molded Tritan Tx more resilient thanPolycarbonate is low profile and vandal resistant. The unit is touch buttonactuated and any of the above configuration of active buttons can be achieved.The patient touches the area denoted by the orange paddle to activate a patientcall. The hidden LED in the centre of the call point illuminates red when thebuttons are touched. A low battery warning will sound when the battery is low.Upon detection of a low battery a CALL signal is sent out this will not besent again until the battery has been changed. While the room units battery islow it will continue to flash its red LED every 15 seconds and sound its buzzerevery 2 minutes. Staff should be made aware of this. The buttons in the framestaff only can be used by the nurse to reset the call. Included 2x torx M3.5x 25mm security screws 3 x AAA batteries surface back box optionalThe wireless call points are a cost-effectiveapproach to add nurse call to an existing staff attack system. This helps keepdisruption to a minimum since no walls need to be chased and are easilyinstalled with an anti-ligature surface collar. The slave wireless call pointsyncs with a master IR receiver which is addressed to understand its location.

GBP 186.30
1

SAS Caring Technology Touch-Wireless-CP-ATT Touch Wireless Call Point with Attack Level No Reset

SAS Caring Technology Touch-Wireless-CP-ATT Touch Wireless Call Point with Attack Level No Reset

SAS Caring Technology Touch-Wireless-CP-ATT Touch Wireless Call Point with Attack Level No ResetDesigned for challenging environments. The room unit manufactured from injection molded Tritan Tx more resilient than Polycarbonate is low profile and vandal resistant. The unit is touch button actuated and any of the above configuration of active buttons can be achieved. The patient touches the area denoted by the orange paddle to activate a patient call. The hidden LED in the centre of the call point illuminates red when the buttons are touched. A low battery warning will sound when the battery is low. Upon detection of a low battery a CALL signal is sent out this will not be sent again until the battery has been changed. While the room units battery is low it will continue to flash its red LED every 15 seconds and sound its buzzer every 2 minutes. Staff should be made aware of this. The buttons in the frame staff only can be used by the nurse to reset the call. Included 2x torx M3.5 x 25mm security screws 3 x AAA batteries surface back box optionalThe wireless call points are a cost effective approach to add nurse call to an existing staff attack system. This helps keep disruption to a minimum since no walls need to be chased and are easily installed with an anti-ligature surface collar. The slave wireless call point syncs with a master IR receiver which is addressed to understand its location.LED FunctionGreen Battery goodYellow Battery should be changedRed Change battery nowPlease note The image is for illustrative purposes only.

GBP 186.30
1

SAS Caring Technology Touch-Wireless-CP-RU Touch Wireless Call Point with Call Reset Crash And Alarm Levels

SAS Caring Technology Touch-Wireless-CP-RU Touch Wireless Call Point with Call Reset Crash And Alarm Levels

SAS Caring Technology Touch-Wireless-CP-RU Touch Wireless Call Point with Call Reset Crash And Alarm LevelsDesigned for challenging environments. The room unit manufactured from injection molded Tritan Tx more resilient than Polycarbonate is low profile and vandal resistant. The unit is touch button actuated and any of the above configuration of active buttons can be achieved. The patient touches the area denoted by the orange paddle to activate a patient call. The hidden LED in the centre of the call point illuminates red when the buttons are touched. A low battery warning will sound when the battery is low. Upon detection of a low battery a CALL signal is sent out this will not be sent again until the battery has been changed. While the room units battery is low it will continue to flash its red LED every 15 seconds and sound its buzzer every 2 minutes. Staff should be made aware of this. The buttons in the frame staff only can be used by the nurse to reset the call. Included 2x torx M3.5 x 25mm security screws 3 x AAA batteries surface back box optionalThe wireless call points are a cost effective approach to add nurse call to an existing staff attack system. This helps keep disruption to a minimum since no walls need to be chased and are easily installed with an anti-ligature surface collar. The slave wireless call point syncs with a master IR receiver which is addressed to understand its location.LED FunctionGreen Battery goodYellow Battery should be changedRed Change battery nowPlease note The image is for illustrative purposes only.

GBP 202.50
1

SAS Caring Technology Touch-Wireless-CP-R Touch Wireless Call Point with Call Reset Reset And Test Levels

SAS Caring Technology Touch-Wireless-CP-R Touch Wireless Call Point with Call Reset Reset And Test Levels

SAS Caring Technology Touch-Wireless-CP-R Touch Wireless Call Point with Call Reset Reset And Test LevelsDesigned for challenging environments. The room unit manufactured from injection molded Tritan Tx more resilient than Polycarbonate is low profile and vandal resistant. The unit is touch button actuated and any of the above configuration of active buttons can be achieved. The patient touches the area denoted by the orange paddle to activate a patient call. The hidden LED in the centre of the call point illuminates red when the buttons are touched. A low battery warning will sound when the battery is low. Upon detection of a low battery a CALL signal is sent out this will not be sent again until the battery has been changed. While the room units battery is low it will continue to flash its red LED every 15 seconds and sound its buzzer every 2 minutes. Staff should be made aware of this. The buttons in the frame staff only can be used by the nurse to reset the call. Included 2x torx M3.5 x 25mm security screws 3 x AAA batteries surface back box optionalThe wireless call points are a cost effective approach to add nurse call to an existing staff attack system. This helps keep disruption to a minimum since no walls need to be chased and are easily installed with an anti-ligature surface collar. The slave wireless call point syncs with a master IR receiver which is addressed to understand its location.LED FunctionGreen Battery goodYellow Battery should be changedRed Change battery nowPlease note The image is for illustrative purposes only.

GBP 186.30
1

Vesda Xtralis VPS-220-STX5-SLV Power Supply 0.5A 7-14AH PSU-STX - Silver

Vesda Xtralis VPS-220-STX5-SLV Power Supply 0.5A 7-14AH PSU-STX - Silver

Vesda Xtralis VPS-220-STX5-SLV Power Supply 0.5A 7-14AH PSU-STX - SilverVESDA-E Power Supply Units are uniquely designed to complement the style and appearance of VESDA-E aspirating smoke detectors ASDs and are technically matched to provide sufficient current and battery charging capacity to meet the requirement of EN 54-4.The STX variants are VdS certified and CE marked to EN54-4 so are particularly suitable for use in territories where these approvals are required. Style STX Product Range Designed with the same widths and styling of the VESDA-E detectors these power supplies geometrically blend with the VESDA-E detectors.They feature the same curved profile and also incorporate an internal channel which accommodates the exhaust of the VESDA-E detectors. This is particularly useful when it is necessary to run the 25mm exhaust pipe back to the protected area back-venting.The units are available in two colours Matt black is standard and works in harmony with the finish of the black plastic VESDA-E detectors the P variants or contrasts with the extruded aluminium finish of other variants.Alternatively the unit can also be supplied with a grey RAL 7047 cover which complements the extruded aluminium finish of the premium VESDA-E Detectors.VPS-220-STX5 VPS220-STX5-SLV 0.5A load with 14Ah batteries max These are the shallower units in the range with depth and width matching the VESDA-E detectors.Internally they provide an EN 54-4 certified Power Supply rated to provide a 0.5A continuous 24Vdc supply whilst also charging the batteries not supplied which can be a 7 12 or uniquely 14Ah arrangement.As such the unit can be used with confidence to power and provide 24hr standby plus 0.5hr in alarm for the VESDA VLF-500 VESDA-E VEP VESDA-E VES detectors and also the VESDA-E VEU detectors up to fan speed 5.The unit also provides a non-certified setting which enables it to power loads up to 1A while recharging batteries up to 12Ah in accordance with EN 54-4.

GBP 340.01
1

C-Tec CL1UK Mini Counter Hearing Loop Kit 1.2m2

C-Tec CL1UK Mini Counter Hearing Loop Kit 1.2m2

C-Tec CL1UK Mini Counter Hearing Loop Kit 1.2m2Hearing loop systems allow hearing impaired people to hear more clearly. Most hearing aids have a T or MT switch which allows them to pick up the electromagnetic field generated by a hearing loop system. The hearing aid converts this signal into a sound suited to its users specific hearing requirements.Any person with a hearing aid positioned within or near the loop can hear the loop signal by switching their hearing aid to the correct position allowing them to participate more effectively in general conversation ordering goods or services listening to public performances etc.The C-Tec SigNET CL1UK mini counter induction loop system kit is the ideal high-quality stand-alone audio frequency induction loop system AFILS for a desk or counter application in a bank post office or ticket booth. The miniature loop amp generates a localised loop field ideal for one-to-one communication. The kit comes complete with loop amp power supply pre-formed counter loop microphone induction loop present sticker.Key FeaturesIdeal for banks post offices small meeting rooms reception desks ticket boothsand any other application requiring restricted or small area coverageGenerates a loop listening field of 4 sq.ft 1.2m2 Kit includes a compact CL1 mini-induction loop amplifier cw UL listed power supply an AMT microphone a TX121 pre-formed counter loop and AFILS available stickerAdjustable drive control level and line controls allows the amplifiers output stage to be set-up to suit the exact characteristics of the applicationMetal compensation control helps combat the frequency response problems caused by metal absorbing the magnetic fieldState-of-the-art audio processor features an automatic gain control which compensates for poor microphone techniques and helps suppress loud noises hisses and clicksDesigned to be free-standing or wall-mounted using the keyholes providedTechnical SpecificationsInduction Loop Type Wall mounting requires fixed mains wiring and a 25mm back boxCoverage 1.2m2 approx.Dimensions W 143 x H 83 x D 32mm 300g amplifier onlyInputs 1 x 3.5mm remote mic. socket 1 x LineOutreach socket max. 3 Outreach plates per ML1Indicators Input level power on loop drive meter.Controls Mic. input level line input level loop driveKit content ML1 amplifier AMT microphone TX2 pre-formed counter loop AFILS fitted sticker.

GBP 245.82
1