528 results (0,15551 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 Zone

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 Zone

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 ZoneThe Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesTwo wire serial connectionUp to 7 panels per system230V AC or 24V DC powered versionsFull control over main panelVolt free fire and fault contact outputsPart NumberDescriptionE01020L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 2 Zones SurfaceE01040L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 4 Zones SurfaceE01080L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 8 Zones Surface

GBP 201.43
1

Kentec Sigma CP-R Repeater Panel with 230v PSU amp Standard Enclosure 2 - 8 Zone

Kentec Sigma CP-R Repeater Panel with 230v PSU amp Standard Enclosure 2 - 8 Zone

Kentec Sigma CP-R Repeater Panel with 230v PSU Standard Enclosure 2 - 8 ZoneThe Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesSigma CP-R Two wire serial connectionUp to 7 panels per system230V AC or 24V DC powered versionsFull control over main panelVolt free fire and fault contact outputsAncillary PCB Two wire serial connectionUp to 7 boards per system230V AC or 24V DC powered versionsOpen collector zonal fault outputsVolt free fire coincidence and common fault contact outputsVariants AvailablePart NumberDescriptionK01020M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 2 Zones SurfaceK01040M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 4 Zones SurfaceK01080M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 8 Zones Surface

GBP 295.45
1

Elmdene GEN3-34-R 13.8v 3A SMPSU Dual Battery

Elmdene GEN3-34-R 13.8v 3A SMPSU Dual Battery

Elmdene GEN3-34-R 13.8v 3A SMPSU Dual BatteryThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62017 and PD66622017Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientFull current to load plus additional current to charge standby batteryInternal LED PSU statusMains transient protection

GBP 199.39
1

Nittan Intrinsically Safe Beacon IS-MB1-R-R

Nittan Intrinsically Safe Beacon IS-MB1-R-R

Nittan Intrinsically Safe Beacon IS-MB1-R-RThe IS-mB1 is a compact beacon with an array of six high output L.E.Ds. Approvals include ATEX IECEx and EAC Ex for Zone 0 applications and FM approval for Class I Division 1 and Class I Zone 0 applications. The IS-mB1 is suitable for all intrinsically safe signalling applications including fire security and process control.Key FeaturesInput overload and reverse current protectionEnd of line resistor certifiedPrismatic lens optimises L.E.D effectiveness

GBP 313.56
1

Haes 2-12 Zone Fully Functional or Passive Repeater Panel XLEN-R-12

Haes 2-12 Zone Fully Functional or Passive Repeater Panel XLEN-R-12

Haes 2-12 Zone Fully Functional or Passive Repeater Panel XLEN-R-12The Excel-EN repeater panels have the same easy to use controls and indications as the main control panel but mounted in a smaller cabinet. The repeaters are fully functional with Silence Resound and Reset controls as well as Disable and Test Mode functions. It is also possible to disable the controls for each or all repeater panels to make them passive indication only. Excel-EN panels can support up to 8 repeater panels.Repeater panels are designed to be wired in a fault tolerant fail safe loop configuration from comms A to B and back to the main panel again. This enables repeater panels to still work if there is a break in the cables. If replacing an older system where the existing cabling cannot be configured in a loop as above it is possible to re-programme the panel back to legacy radial circuit comms monitoring. This then allows any topology of comms cabling to be utilised.The main circuit board has 2 switch ve inputs which can be used to sound or pulse the alarms. These inputs can also be re-programmed for use as PSU fault inputs. The internal comms PCB has 6 switch ve programmable outputs.Key Features12 zonal fire fault indications3 year warranty as standardSimple colour coded buttons for controlsIntegral 1 amp switch mode PSUClass change alert inputsProgrammable outputsTest mode disablement functionsFully functional or passiveSpace for up to 3.2Ah batteriesKey-switch or code entry for activation of controls

GBP 370.74
1

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Sigma CP-R Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs Ancillary PCB Two wire serial connection Up to 7 boards per system 230V AC or 24V DC powered versions Open collector zonal fault outputs Volt free fire coincidence and common fault contact outputs

GBP 366.24
1

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Sigma CP-R Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs Ancillary PCB Two wire serial connection Up to 7 boards per system 230V AC or 24V DC powered versions Open collector zonal fault outputs Volt free fire coincidence and common fault contact outputs

GBP 304.18
1

Ziton ZP3AB-SCB-R Serial Control Bus Interface

Ziton ZP3AB-SCB-R Serial Control Bus Interface

Ziton ZP3AB-SCB-R Serial Control Bus InterfaceThe ZP3AB-SCB-R provides a remote interface on the system control bus wiring enabling repeat indication and system control at locations remote from the main panel position.The interface can be positioned anywhere on the system bus wiring which it shares with remote display units RDUs. Driven from within the main control panel by an optional SCB-D driver board a combination of up to 32 or 64 RDUs and SCB-Rs can be controlled dependant upon the ZP3 panel software.Usually installed within auxiliary equipment cabinets the interface is compatible with all ZP3AB optional facility boards including the RL8 relay module the MIP8 input card and the OP24 open collector output card.The ZP3AB-SCB-D and SCB-R serial control bus driver and interface are part of the range of optional facility boards which can be added cost effectively to any ZP3 system in order to provide extra facilities which may not be a requirement of every system.Key FeaturesUp to 32 or 64 remote serial interfaces - dependant upon control panel softwareShares common wiring with remote display unitsRS 485 communication protocolFlexible wiring connection

GBP 292.39
1

Cranford Controls IS-MA1-R Intrinsically Safe Minialarm Sounder

Cranford Controls IS-MA1-R Intrinsically Safe Minialarm Sounder

Cranford Controls IS-MA1-R Intrinsically Safe Minialarm Sounder - RedThe intrinsically safe range of products includes the compact IS-minialarm sounder IS-minialite beacon and IS-minialert sounderbeacon. The range is suitable for all intrinsically safe signalling applications including fire security and process control. Approvals include ATEX IECEx FMVdS and GOST-R.The IS-minialite beacon optimises the effectiveness of its six high output LEDs via a prismatic lens design. The IS-minialert combined sounder and beacon requires only one Zener barrier or galvanic isolator to run both sounder and beacon or alternatively the unit can be operated as individual signals.Key Features Input overload and reverse current protectionEnd of line resistor certifiedATEX IECEx FM and GOST-R approvalsIS-minialarm has VdS approval to EN54-32 x M20 clearance gland knockoutsAuto synchronised sound output exc. minialitePowered from any certified Zener barrier or galvanic isolator

GBP 253.64
1

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs

GBP 210.79
1

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs

GBP 254.51
1

Vimpex Intrinsically Safe Sounder Red IS-A105N-R

Vimpex Intrinsically Safe Sounder Red IS-A105N-R

Vimpex Intrinsically Safe Sounder Red IS-A105N-RThe IS-A105N is suitable for all intrinsically safe signalling applications including fire security and process control. The IS-A105N is a high output 105dBA alarm sounder. Approvals include ATEX IECEx and GOST-R for Zone 0 applications and FM approval for Class I Division 1 and Class I Zone 0 applications.Key FeaturesInput overload and reverse current protectionAuto synchronised sound outputUnit can be mounted using external lugs or internal BESA compatible fixing positions.Duplicate cable terminations in out for daisy-chain installations.Available with custom tone configurations and frequencies.

GBP 342.10
1

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-R

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-R

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-RThe IS-mA1 is a compact 100dBA alarm sounder. Approvals include ATEX IECEx and GOST-R for Zone 0 applications and FM approval for Class I Division 1 and Class I Zone 0 applications.It is suitable for all intrinsically safe signalling applications including fire security and process control.Key FeaturesInput overload and reverse current protectionEnd of line resistor certifiedAuto synchronised sound outputAvailable with custom tone configurationsGroup1 Mining

GBP 247.62
1

Signaline SL-FT-68-R Fixed Temperature Linear Heat Sensing Cable - 68C Black Nylon Chemical Resistant

Signaline SL-FT-68-R Fixed Temperature Linear Heat Sensing Cable - 68C Black Nylon Chemical Resistant

Signaline SL-FT-68-R Fixed Temperature Heat Sensing Cable - 68 deg.C Black Nylon Chemical Resistant UL ApprovedThe Signaline SL-FT-68-R is a 50 metre roll of fixed temperature 68 degrees Celsius linear heat cable. This is the black nylon chemical resistant version.Signaline Fixed Temperature Linear Heat DetectorSignaline FT detects a build-up of heat anywhere along its length. When any point along the length of the cable reaches a predetermined temperature an alarm is initiated. Signaline FT is available in four different temperature settings and two outer cover options making the Signaline FT suitable for use in a very wide range of applications.Key Features50 Metres

GBP 285.60
1

Haes ASP-R-12 AlarmSense PLUS 12 Way Repeater Panel

Haes ASP-R-12 AlarmSense PLUS 12 Way Repeater Panel

Haes ASP-R-12 AlarmSense PLUS 12 Way Repeater PanelA 12 zone fully functional or passive fire alarm repeater panel suitable for the AlarmSense PLUS panel range not suitable for ALS panels.The AlarmSense PLUS 12 way repeater panels have the same easy to use controls and indications as the main control panel.The repeaters are fully functional with Silence Resound and Reset controls as well as Disable and Test Mode functions. It is also possible to disable the controls for each or all repeater panels to make them passive indication only.The main circuit board has 2 switch ve inputs which can be used to sound or pulse the alarms. These inputs can also be re-programmed for use as PSU fault inputs.The internal comms PCB has 6 switch ve programmable outputs.The repeaters are supplied with a 1.25 amp internal power supply module.This module complies with the requirements of EN54-4 1988 and provides temperature compensated battery management chargingKey Features12 zonal fire and fault indicationsActivate controls via key switch or code entry1.25 Amp switch mode power supply Nom 27V DCClass change IPAlert IP6 programmable switched -ve outputsTest mode with or without soundersDisable zones sounder OPs aux OPs delays

GBP 372.60
1

Haes ESEN-R-12MAR 12 Zone Conventional Esento MED Marine Approved Repeater Panel

Haes ESEN-R-12MAR 12 Zone Conventional Esento MED Marine Approved Repeater Panel

Haes ESEN-R-12MAR 12 Zone Conventional Esento MED Marine Approved Repeater PanelThe Esento Marine 12 way repeater panels have the same easy to use controls and indications as the main control panel. The repeaters are fully functional with Silence Resound and Reset controls as well as Disable and Test Mode functions. It is also possible to disable the controls for each or all repeater panels to make them passive indication only.The main circuit board has 2 switch ve inputs which can be used to sound or pulse the alarms. These inputs can also be re-programmed for use as PSU fault inputs. The internal comms PCB has 6 switch ve programmable outputs. The repeaters are supplied with a 1.25 amp internal power supply module. This module complies with the requirements of EN54-4 1988 and provides temperature compensated battery management charging.Key Features12 zonal fire and fault indicationsActivate controls via keyswitch or code entry1.25 Amp switch mode power supply Nom 27V DCClass change IPAlert IP6 programmable switched -ve outputsTest mode with or without soundersDisable zones sounder OPs aux OPs delays

GBP 365.94
1