25 results (0,16910 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Notifier HOP-402-100 Charger Module 1 Supplied

Notifier HOP-402-100 Charger Module 1 Supplied

Notifier HOP-402-100 Charger Module 1 SuppliedA Charger Module designed for use with the INSPIRE panels.Key FeaturesCharge and discharge current monitoringUnder Voltage Lockout to prevent system going into undefined stateOver Voltage Lockout to prevent batteries overchargingBattery condition monitored via load testBattery wiring fault monitoredIntelligent battery charging by local monitoring of battery temperature and connecting cable openshort circuit fault

GBP 296.09
1

Cygnus SN.RB20.2 SmartNet-Pro VID Sounder Radio Ring Base Red Ring

Cygnus SN.RB20.2 SmartNet-Pro VID Sounder Radio Ring Base Red Ring

Cygnus SN.RB20.2 SmartNet-Pro VID Sounder Radio Ring Base Red RingThe SmartNet-Pro VID Sounder Radio is part of a range of detector heads including optical smoke heat and combi sensors. The wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocol.Key FeaturesCertified to EN 54-25 and EN 54-3100 wirelessRange of detector heads including optical smoke heat and combi sensorsAnalogue detection with intelligent sensing technology32 sounder tonesVisual Indicator VI ring flashes in alarm modeAddressable through the Cygnus configuration toolLocking detector and base mechanism for enhanced securitySeparate interlocking ceiling mount plate for easy installationEasy to remove with detachment toolUltra-low powered device 3.6v nominalBattery operated with a minimum three years battery lifeThe wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocolPatented self-forming and self-healing mesh Cygnus technologyMulti colour LED status indication

GBP 271.75
1

Cygnus S1.RB20.1 SmartNet-100 VID Sounder Radio White Base White Ring

Cygnus S1.RB20.1 SmartNet-100 VID Sounder Radio White Base White Ring

Cygnus S1.RB20.1 SmartNet-100 VID Sounder Radio White Base White RingA SmartNet-100 VID Sounder Radio Base which is certified to EN 54-25 and EN 54-3. It features a white ring and 32 sounder tones. This 100 wireless base is addressable through the Cygnus Configuration Tool and enables a mesh network to other devices and to the main panel through the Cygnus wireless protocol.Key FeaturesCertified to EN 54-25 and EN 54-3100 wirelessRange of detector heads including optical smoke heat and combi sensorsAnalogue detection with intelligent sensing technology32 sounder tonesVisual Indicator VI ring flashes in alarm modeAddressable through the Cygnus configuration toolLocking detector and base mechanism for enhanced securitySeparate interlocking ceiling mount plate for easy installationEasy to remove with detachment toolUltra-low powered device 3.6v nominalBattery operated with a minimum three years battery lifeThe wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocolPatented self-forming and self-healing mesh Cygnus technologyMulti colour LED status indication

GBP 220.08
1

Cygnus S1.RB20.1A SmartNet-100 VID Sounder Radio White Base Red Ring

Cygnus S1.RB20.1A SmartNet-100 VID Sounder Radio White Base Red Ring

Cygnus S1.RB20.1A SmartNet-100 VID Sounder Radio White Base Red RingA SmartNet-100 VID Sounder Radio Base which is certified to EN 54-25 and EN 54-3. It features a red ring and 32 sounder tones. This 100 wireless base is addressable through the Cygnus Configuration Tool and enables a mesh network to other devices and to the main panel through the Cygnus wireless protocol.Key FeaturesCertified to EN 54-25 and EN 54-3100 wirelessRange of detector heads including optical smoke heat and combi sensorsAnalogue detection with intelligent sensing technology32 sounder tonesVisual Indicator VI ring flashes in alarm modeAddressable through the Cygnus configuration toolLocking detector and base mechanism for enhanced securitySeparate interlocking ceiling mount plate for easy installationEasy to remove with detachment toolUltra-low powered device 3.6v nominalBattery operated with a minimum three years battery lifeThe wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocolPatented self-forming and self-healing mesh Cygnus technologyMulti colour LED status indication

GBP 220.08
1

Cygnus S1.RB20.2 SmartNet-100 VID Sounder Radio Red Base Red Ring

Cygnus S1.RB20.2 SmartNet-100 VID Sounder Radio Red Base Red Ring

Cygnus S1.RB20.2 SmartNet-100 VID Sounder Radio Red Base Red RingA SmartNet-100 VID Sounder Radio Base which is certified to EN 54-25 and EN 54-3. It features a red ring and 32 sounder tones. This 100 wireless base is addressable through the Cygnus Configuration Tool and enables a mesh network to other devices and to the main panel through the Cygnus wireless protocol.Key FeaturesCertified to EN 54-25 and EN 54-3100 wirelessRange of detector heads including optical smoke heat and combi sensorsAnalogue detection with intelligent sensing technology32 sounder tonesVisual Indicator VI ring flashes in alarm modeAddressable through the Cygnus configuration toolLocking detector and base mechanism for enhanced securitySeparate interlocking ceiling mount plate for easy installationEasy to remove with detachment toolUltra-low powered device 3.6v nominalBattery operated with a minimum three years battery lifeThe wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocolPatented self-forming and self-healing mesh Cygnus technologyMulti colour LED status indication

GBP 220.08
1

Cygnus SN.RB20.1 SmartNet-Pro VID Sounder Radio White Base White Ring

Cygnus SN.RB20.1 SmartNet-Pro VID Sounder Radio White Base White Ring

Cygnus SN.RB20.1 SmartNet-Pro VID Sounder Radio White Base White RingThe SmartNet-Pro VID Sounder Radio is part of a range of detector heads including optical smoke heat and combi sensors. The wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocol.Key FeaturesCertified to EN 54-25 and EN 54-3100 wirelessRange of detector heads including optical smoke heat and combi sensorsAnalogue detection with intelligent sensing technology32 sounder tonesVisual Indicator VI ring flashes in alarm modeAddressable through the Cygnus configuration toolLocking detector and base mechanism for enhanced securitySeparate interlocking ceiling mount plate for easy installationEasy to remove with detachment toolUltra-low powered device 3.6v nominalBattery operated with a minimum three years battery lifeThe wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocolPatented self-forming and self-healing mesh Cygnus technologyMulti colour LED status indication

GBP 271.75
1

Cygnus SN.RB20.1A SmartNet-Pro VID Sounder Radio White Base Red Ring

Cygnus SN.RB20.1A SmartNet-Pro VID Sounder Radio White Base Red Ring

Cygnus SN.RB20.1A SmartNet-Pro VID Sounder Radio White Base Red RingThe SmartNet-Pro VID Sounder Radio is part of a range of detector heads including optical smoke heat and combi sensors. The wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocol.Key FeaturesCertified to EN 54-25 and EN 54-3100 wirelessRange of detector heads including optical smoke heat and combi sensorsAnalogue detection with intelligent sensing technology32 sounder tonesVisual Indicator VI ring flashes in alarm modeAddressable through the Cygnus configuration toolLocking detector and base mechanism for enhanced securitySeparate interlocking ceiling mount plate for easy installationEasy to remove with detachment toolUltra-low powered device 3.6v nominalBattery operated with a minimum three years battery lifeThe wireless addressable base enables a mesh network to other devices and to the main panel through the Cygnus wireless protocolPatented self-forming and self-healing mesh Cygnus technologyMulti colour LED status indication

GBP 271.75
1

C-Tec ZFP Multi-Path Fault Tolerant Network PCB

C-Tec ZFP Multi-Path Fault Tolerant Network PCB

C-Tec ZFP Multi-Path Fault Tolerant Network PCBAllows the interconnection of up to 64 ZFP Main Panels any mix and up to 64 ZFP Compact Controllers over a two-wire RS485 ring-wired multi-path fault-tolerant Hi-Net network. One ZHN required per ZFP Main Panel ZFP Compact Controllers include a ZHN PCB as standard.Key FeaturesRS485 ProtocolMax. cable length between nodes 1KMMax. cable length of entire network 128KMFor retrofits multiple ZHNs can be wired in a non-fault tolerant single-path network configuration Max. 8 nodes Max length of entire network must not exceed 1KM.

GBP 294.67
1

Zeta SCM-NM Network Module

Zeta SCM-NM Network Module

Zeta SCM-NM Network ModuleThe Smart Connect Multiloop system network has the facility to monitor indicate and control the functions of a fire alarm installation thus allowing signals to be distributed around a large site.The network will accommodate up to 64 nodes. The network uses RS485 data communication and a total network cable length of up to 10km is possible.On a Smart Connect Multiloop running in a network all events are reported at all panels are able to remotely program other panels sitting on the network. Operation of outputs over the network is determined by the programmed cause effects. Any input on the network can be programmed to operate any output.Key FeaturesDesigned to EN54 requirementsPeer-to-peer networkingComprehensive cross network cause effectsUp to 64 panels may be networked togetherRemote programming over the networkThe network can be configured with either a ring or bus topologyFault tolerant designExtensive front unit status indicationsQuick and easy to install by plugging the RJ45 cable into the module and control panel Cable supplied with unit

GBP 323.02
1

Baldwin Boxall Omnicare Type B Green Disabled Refuge Remote BVOCECPG

Baldwin Boxall Omnicare Type B Green Disabled Refuge Remote BVOCECPG

Baldwin Boxall Omnicare Type B Green Disabled Refuge Remote BVOCECPGThe OmniCare system offers a choice of outstation units which can be wired on the same loop from the control panel. The BVOCECPG standard green disabled refuge remote unit is one of the options available on this versatile system.Key FeaturesProvides two-way hands free speech steered communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Green finish also available in stainless steel BVOCECPG.Addressable unit.Volt free contact active when occupied. To operate over-door lamps silence speakersounder etc.Stainless steel press to call button.Calls can be reset either by of the key-switch on the remote unit or at the master control panel.Option to be permanently active if required.Reset from either remote unit using the key switch or via the master control panel.All outstations are in a loop circuit from control panels.A link to the fire detection system prevents hoax disabled refuge calls. This feature can be completely or partly overridden.Surface mounting unit can be flush mounted using a bezel.

GBP 434.54
1

Ziton 2010-2F1-MB ZP2 Main PCB - 1 Loop

Ziton 2010-2F1-MB ZP2 Main PCB - 1 Loop

Ziton 2010-2F1-MB ZP2 Main PCB - 1 LoopThe 2010-2F1-MB is a replacement main board for all ZP2 1 loop control panels.Key Features1 Ring with up to 64 zones and the main detector control unitAuto - configuration and regional commissioning modeEthernet port with TCP IP for remote maintenance and programmingAll Terminals pluggable3 USB ports with memory stick support3 RS232 interfaces24 V DC supply alarm switch with reset functionVdS approval G 210005Technical SpecificationsPower supply Operating voltage 230110 V AC 10 -15Operating Current Nom. 0.6 1.3 A Max. 1.5 3.15 AFrequency 5060 Hz 5Backup 24 ACable Type 3 x 1.5 mm line neutral earthOutputs Fire Alarm fault monitors 2350 mA 19.5 to 28 V DCProgrammable monitored 2750 mA 19.5 to 28 V DCAUX 1 switched 500 mA 19.5 to 28 V DCFire Alarm fault relay 2Terminator AG 15 kOhmInputs Programmable 2Maximum load 150mATerminator EC 15 kOhmCable Characteristics Outputs 1250 mA 29 V DC to 36 V DCCable length 56ohm 1uF max. 4 kmEnvironmental conditions Storage temperature -20 C to 50 COperating temperature -5 C to 40 CDimensions Overall dimensions W x H 320 x 110 mmAdmission VdS Approved G 211005

GBP 349.94
1

Baldwin Boxall Omnicare Repeater Unit BVOCRIF

Baldwin Boxall Omnicare Repeater Unit BVOCRIF

Baldwin Boxall Omnicare Repeater Unit BVOCRIFThe EVC repeater unit - BVOCRIF - enables our DTAKIT disabled toilet alarm products to be added to an Omnicare system. The BVOCRIF also acts as a line booster to enable longer cable lengths between outstations andor control panels.Key FeaturesUse the BVOCRIF as an interface for the DTAKIT three part toilet alarm system.Up to two DTAKITs can be fitted to each BVOCRIF repeater will show as one point on the control panel.As an alternative one DTAKIT and an additional pull cord can be fitted to a BVOCRIF. Useful for rooms with two points of call e.g. a toilet cubicle with a shower area.Replaces the BVFREPEM repeater unit formerly used to connect the BVOCDTA products to an Omnicare system.The DTAKIT is suitable for installation on any Omnicare system via the BVOCRIF repeater. The only exception to this is if a system already has the BVOCDTA kits and BVFREPEM repeater modules connected.The BVOCRIF can act as a booster unit to enable cable runs exceeding 200 metres between remote units outstations andor control panels.Repeater units are not seen as an address on the control panel unless connected to a disabled toilet alarm.An internal termination board includes loop through connector for testing site wiring.Self-powered from the ring circuit.Surface mountable.Zintec finish.

GBP 205.93
1

EMS FC-K545 Syncro IO 4 Way Conventional Detection Zone Module

EMS FC-K545 Syncro IO 4 Way Conventional Detection Zone Module

EMS FC-K545 Syncro IO 4 Way Conventional Detection Zone ModuleThe Syncro 4-way conventional zone module provides a cost effective solution to system upgrades where a number of conventional detection zones need to be supported by the Syncro panel in addition to the analogue addressable detection devices.Up to 32 Syncro 4-way conventional zone modules may be connected to each Syncro or Syncro AS control panel providing support for up to 128 conventional detection zones per Syncro panel. The zone cards utilise RS485 data communications and may be installed up to 1200m away from the panel using suitable data cable.Each Syncro 4-way conventional zone module has four independently monitored conventional detection zones short circuit and open circuit monitoring two independent 1 Amp rated fully monitored sounder outputs a volt free Fire relay Fault relay and an input to monitor a remote power supply.All inputs and outputs are configurable using the intuitive Syncro Loop Explorer configuration program. Each zone may have a 40 character location message allocated and may be mapped to any of the 500 detection zones supported by Syncro and Syncro AS panels. The inputs and outputs may be controlled either via the simple default ring patterns or by comprehensive cause and effect logic. In the unlikely event that there is a loss of data between the panel and the 4-way conventional zone card then it will work stand alone in a default condition whereby a fire on any of the four zones will result in both sounder circuits and the fire contact operating continuously.

GBP 304.00
1

Kidde 1X-X3E-99 Conventional Fire amp Extinguishing Panel With UI - 3 Zone - Full Opt Eng Int

Kidde 1X-X3E-99 Conventional Fire amp Extinguishing Panel With UI - 3 Zone - Full Opt Eng Int

Kidde 1X-X3E-99 Conventional Fire Extinguishing Panel With UI - 3 Zone - Full Opt Eng IntThe 1X-X3E-99 is a networkable enhanced conventional fire alarm and extinguishing control panel. It is supplied in local language with 3 fire zones that support up to 32 devices per zone. These zones may be configured for extinguishing in single zone or double zone configuration in any combination of zones. In addition the panel offers supervised outputs for first stage notification second stage notification as well as optical warning indicators and actuator activation. Standard relay outputs are provided for EN54 compliance and system status notification as well as multiple inputs for system control.The 1X fire control panels offer state of the art architecture in configurations that deliver an uncomplicated solution for small to mid-sized conventional applications. They feature an attractive contemporary design that fits with any dcor. The gently curved door front offers a distinctive flair. Operator controls are inset in a striking black lexan.With support for multiple lines of conventional detectors and accessories these quick-to-configure systems offer versatility that benefits building owners and installationmaintenance companies alike.OptionsThe panels support 2 types of auxiliary relay boards one with 4 standard relays and one with 4 supervised relays. With these boards the panel outputs may be expanded with up to 16 additional outputs. The 1X-X3E supports class A redundant ring and B standard bus networking with up to 32 nodes including conventional and addressable panels and repeaters via an optional network interface. This allows full remote control and inputs to and from other nodes in the system providing superior flexibility in system organization and planning.Key FeaturesSounders configurable for pulsing or continuous operationExtinguishing agent flow confirmationContinuous or resettable 24 VDC auxiliary supplyAuxiliary standard supervised relay output supportIntrinsically safe and EN54-13 zone support

GBP 412.79
1

Carrier ABT-M04N PAVA Microphone Station - 4 Button Network

Carrier ABT-M04N PAVA Microphone Station - 4 Button Network

Carrier ABT-M04N PAVA Microphone Station - 4 Button NetworkThe ABT-M04N is a 4 button analogue microphone with built in AUX input push to talk key and LED indicating the ready-to-speak status with AUX active status. Microphone can be daisy chained with up to 35 microphones. Number of connected microphones depends on the total length of the Cat5e cable and supply voltage.To operate the device first select the Zones by pressing designated buttons and then press MIC button. The Mic LED will start blinking green for the time of matrix activation. When Mic led is green and red ring on the goose neck lights up microphone is ready for live announcement. On the other microphones connected in the chain AUX LED and MIC LED are blinking indicating that live announcement is being broadcast on other microphone. When finished transmitting the message release the MIC button to deactivate the gooseneck micOnly one microphone can have aux input active. To use it please connect device to 35mm jack socket market as AUX select the zones to which AUX signal will be transfer and select AUX button to create connection. Green led on Aux indicates that microphone has active aux input on the other microphones in the chain AUX LED is blinking green. Microphone always has the higher priority over the AUX. When aux is activated on selected zones on one microphone it is possible to select different zones for live broadcast on other microphones.Deactivation of the MIC will activate previously selected zones with AUX.Key FeaturesDaisy chain connection up to 35 micsSimple Cat5e interconnectionAUX input with dedicated volumecontrolMicrophone gooseneck with LED redring indicationActive MIC AUX in use informationbetween microphonesWide range of operating voltagesLong connection distances up to2200m

GBP 222.78
1

Haes ESEN-2MAR 2 Zone Conventional Esento MED Marine Approved Control Panel

Haes ESEN-2MAR 2 Zone Conventional Esento MED Marine Approved Control Panel

Haes ESEN-2MAR 2 Zone Conventional Esento MED Marine Approved Control PanelThe Esento Marine 2-4 panel is available with 2 or 4 conventional zones. The programming features include programmable muster alarm zones and a false alarm management mode. As standard all Esento Marine 2-4 panels provide two monitored sounder circuits Fire Fault VFCO relays and inputs to ring and pulse the sounder circuits. A separate interface card is also available to connect the panel to a ships voyage data recorder system.The panels are supplied with a 1.25 amp internal power supply module. This module complies with the requirements of EN54-4 1988 and provides temperature compensated battery management charging. Esento Marine panels are approved to European standards EN54-2 4 Fire Detection and Alarm Systems Control Indicating Equipment.Essento Marine OverviewThe Esento Marine range from Haes has been exclusively developed to address the issues of limited form and function in the conventional panels market for use at sea. Designed with the severity of the potential situation in mind these new panels are equipped with programmable delays to outputs which allow time for an investigation before invoking a full evacuation or muster alarm.Not only does this new feature-rich panel mitigate false alarms with three false alarm management mode options it also contains additional components within the casing to ensure its not disrupted by increased vibrations encountered during a journey.The panels are available from 2 - 12 zones and offer a fully comprehensive suite of programmable features for the engineer. The display uses super bright clearly labelled LED indicators and the simple colour coded buttons give the end user the confidence to correctly manage their fire alarm system.Key Features2 or 4 zonesActivate controls via keyswitch or code entryCompatible with Apollo Orbis Marine detectorsIntegral detector removal monitoringEarth fault monitoring1.25 Amp switch mode power supply Nom 27V DC2 monitored sounder outputs2 Aux CO relays 1 x Fire 1 x Fault. voltage freeClass change IPAlert IPFire fault switched -ve outputsFalse alarm modeMuster alarm featureTest mode with or without soundersDisable zones sounder OPs aux OPsAlarm load 800mA shared between all sounder outputsAll sounder circuits are fused 500mA with resettable fuses.

GBP 318.82
1

Haes ESEN-4MAR 4 Zone Conventional Esento MED Marine Approved Control Panel

Haes ESEN-4MAR 4 Zone Conventional Esento MED Marine Approved Control Panel

Haes ESEN-4MAR 4 Zone Conventional Esento MED Marine Approved Control PanelThe Esento Marine 2-4 panel is available with 2 or 4 conventional zones. The programming features include programmable muster alarm zones and a false alarm management mode. As standard all Esento Marine 2-4 panels provide two monitored sounder circuits Fire Fault VFCO relays and inputs to ring and pulse the sounder circuits. A separate interface card is also available to connect the panel to a ships voyage data recorder system.The panels are supplied with a 1.25 amp internal power supply module. This module complies with the requirements of EN54-4 1988 and provides temperature compensated battery management charging. Esento Marine panels are approved to European standards EN54-2 4 Fire Detection and Alarm Systems Control Indicating Equipment.Essento Marine OverviewThe Esento Marine range from Haes has been exclusively developed to address the issues of limited form and function in the conventional panels market for use at sea. Designed with the severity of the potential situation in mind these new panels are equipped with programmable delays to outputs which allow time for an investigation before invoking a full evacuation or muster alarm.Not only does this new feature-rich panel mitigate false alarms with three false alarm management mode options it also contains additional components within the casing to ensure its not disrupted by increased vibrations encountered during a journey.The panels are available from 2 - 12 zones and offer a fully comprehensive suite of programmable features for the engineer. The display uses super bright clearly labelled LED indicators and the simple colour coded buttons give the end user the confidence to correctly manage their fire alarm system.Key Features2 or 4 zonesActivate controls via keyswitch or code entryCompatible with Apollo Orbis Marine detectorsIntegral detector removal monitoringEarth fault monitoring1.25 Amp switch mode power supply Nom 27V DC2 monitored sounder outputs2 Aux CO relays 1 x Fire 1 x Fault. voltage freeClass change IPAlert IPFire fault switched -ve outputsFalse alarm modeMuster alarm featureTest mode with or without soundersDisable zones sounder OPs aux OPsAlarm load 800mA shared between all sounder outputsAll sounder circuits are fused 500mA with resettable fuses.N.B. No networking or repeater panels

GBP 379.13
1

Ziton Conventional Fire and Extinguishing Panel EN12094 3 Zone ZP1-X3E-03

Ziton Conventional Fire and Extinguishing Panel EN12094 3 Zone ZP1-X3E-03

Ziton Conventional Fire and Extinguishing Panel EN12094 3 Zone ZP1-X3-03ZP1 fire control panels offer state of the art architecture in configurations that deliver an uncomplicated solution for small to mid-sized conventional applications. They feature an attractive contemporary design that fits with any decor. The gently curved door front offers a distinctive flair. Operator controls are inset in a striking blue lexan. With support for multiple lines of conventional detectors and accessories these quick-to-configure systems offer versatility that benefits building owners and installationmaintenance companies alike.The ZP1-X3 is a conventional fire alarm and extinguishing control panel. It is supplied in local language with 3 fire zones that support up to 32 devices per zone. These zones may be configured for extinguishing in single zone or double zone configuration in any combination of zones. In addition the panel offers supervised outputs for first stage notification second stage notification as well as optical warning indicators and actuator activation. Standard relay outputs are provided for EN54 compliance and system status notification as well as multiple inputs for system control.The panels support 2 types of auxiliary relay boards one with 4 standard relays and one with 4 supervised relays. With these boards the panel outputs may be expanded with up to 16 additional outputs.The ZP1-X3E supports class A redundant ring and B standard bus networking with up to 32 nodes including conventional and addressable panels and repeaters via an optional network interface. This allows full remote control and inputs to and from other nodes in the system providing superior flexibility in system organisation and planning.Key FeaturesModern elegant designEasy removable parts for quick and easy installationNormal head-out supervision support per zoneThree detection zones Single zone double zone or any combination of zones configurable for release6 Pre-configured relays and 8 supervised inputs for extinguishing controlConfigurable fire routing sounder extinguishing reset and door monitoring delaysConfigurable Hold Mode type-A or type-B Sounders configurable for pulsing or continuous operationExtinguishing agent flow confirmationContinuous or resettable 24 VDC auxiliary suppliesAuxiliary standard supervised relay output supportDefault support for special functions such as - EN54 compliant user access levels - Basic Advanced level configuration - mixed zones - front panel diagnostics with test disable control - one-man walk testRedundant networking to ZP1 conventional and ZP2 addressable nodesIntrinsically safe and EN54-13 zone support

GBP 376.19
1