15 results (0,14315 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Hochiki WCP1A Marine Conventional Weatherproof Call Point

Hochiki WCP1A Marine Conventional Weatherproof Call Point

Hochiki WCP1A Marine Conventional Weatherproof Call PointTheWCP1A is a Conventional marine-approved weather-proof call-point based upon the industry standard KAC World Series housing and features easy to install push-fit wiring terminals.The unit can support either a Frangible Glass element or a Non Frangible Plastic element and features a weather-proof Housing to IP67 which means it can be mounted in the most severe environmental conditions without water ingress.Key FeaturesApproved to EN54-112001Terminals can accommodate up to a 2.5 mm solid conductorIngress Protection rated to IP67Approved to MED by GLGL Type ApprovalApproved by LPCB

GBP 95.89
1

Hochiki Marine Dual Sounder Controller with SCI CHQ-DSC2MSCI

Hochiki Marine Dual Sounder Controller with SCI CHQ-DSC2MSCI

Hochiki CHQ-DSC2MSCI Marine Dual Sounder Controller with SCIThe CHQ-DSC2MSCI is a Marine Approved Dual Sounder Controller which has been designed to provide two sounder outputs that can be driven separately with full fault monitoring. The monitored input can be used for local power supply fault monitoring or as a general-purpose input.The unit utilises simple DIL switches for reliable addressing. A back box is also available CHQ-BACKBOX which when used in conjunction with the CHQ-DSC2MSCI increases the IP rating to IP65.Key FeaturesSingle loop addressEach alarm circuit fused at 1 ampTwo independent sounder circuits each fully monitored for open and short circuit faultsAuxiliary monitored inputOutputs can be driven continuously or synchronised pulsed sounder driveSmart-Fix housing system for flexibilityFeatures an integral SCIApproved to MED by GLGL Type approvalApproved by LPCB

GBP 111.84
1

Nursecall Intercall FS-PIR InfraRed Bedside Monitor

Nursecall Intercall FS-PIR InfraRed Bedside Monitor

Nursecall Intercall FS-PIR InfraRed Bedside MonitorThe InfraRed Bedside Monitor uses infrared detection technology to determine when a fall risk patient or resident leaves bed. The monitor sounds an alarm to alert the caregiver when the patient breaks an infrared beam eliminating the need for sensor pads or strings attached to the patient. This monitor is battery powered not included making it completely portable andparticularly useful where the presence of cords or strings is undesirable.Beeping or chime alarm options sound locally at the bedside and the monitor also has a nurse call output allowing for connection to most nursecall systems when used with the optional nursecall cable. The InfraRed Bedside Monitor comes with a C-clamp and Velcro strips for easy mounting on the bed frame or on the headboard or footboard of the bed.An optional sturdy extension bracket is also available along with an optional mains power adapter. This monitor comes with a low battery alert one year limited warranty and has been used successfully in thousands of care homes as an aid to help caregivers improve the safety of fall risk residents.Key FeaturesDetects bed exit without the use of sensor pads or strings attached to patientCan be used without any cords or strings near patientBeep or Chime alarm tonesCan be connected to most nurse call systems with optional cablePowered by standard 9-volt battery or optional mains power adaptorMounts easily to bed frame headboard or footboardLow-battery indicatorOne-year warrantyOptional extension mounting bracket 0121-125 Silent alarm option when connected to nurse call system

GBP 128.75
1

C-Tec QT637 Quantec Enuresis General Purpose Interface Socket

C-Tec QT637 Quantec Enuresis General Purpose Interface Socket

C-Tec QT637 Quantec Enuresis General Purpose Interface SocketAllows bed wet sensors floor pressure mats and bedchair exit sensors to be easily interfaced to a Quantec addressable call system. Includes two 6.35mm remote jack sockets - one for use with a QT635 enuresisbed wet sensor and one that will accept a floor pressure mat QT644 bed exit mat QT633 or chair exit mat QT634.Onboard batteryisolation circuit ensurescompliance with all relevant UK medical directives. Connects to Quantec via the ancillary input on a Quantec master call point or a QT630 dementia care controller. Can be programmed to generate a standard help required or emergency call on activation via a QT423 configurator at the master call point.Key FeaturesIncludes a battery test button and low batteryenuresis active indicators.Supplied on a double gang plate typically located at floor level.Requires a PP3 battery.

GBP 89.00
1

Nursecall Intercall 920 Call Point Basic

Nursecall Intercall 920 Call Point Basic

Nursecall Intercall 920 Call Point BasicThe Touch Nurse Call System Call Point Basic is our entry level call point and is suitable for most care environments. The sleek wall mounted design is simple to use for both staff and residents. The call point acts as a central hub for the room whether positioned alongside the bed or in more general areas.Key FeaturesUp to 254 programmable call levelsEach call point is addressableFeatures pear lead connection programmable closing contactsBuilt-in call reassurance LED

GBP 103.27
1

Nursecall Intercall SSD-PIR Wireless PIR Movement Sensor

Nursecall Intercall SSD-PIR Wireless PIR Movement Sensor

Nursecall Intercall SSD-PIR Wireless PIR Movement SensorThe wireless PIR uses infrared detection technology to help carers reduce the risk of falls. This monitor can be mounted on a door or by the bedside to trigger an alert when a person breaks the infrared beam. The device works by emitting a harmless infrared signal which alerts the caregiver when the beam is broken.Wireless PIR monitor is typically used in care homes and medical facilities to alert a caregiver when a client attempts to leave their bed and is at risk of falling or when they pass into a restricted area such as a client leaving their bedroom and potentially wandering away.The alert can be raised as a local alarm in the clients room or by connecting the PIR to the nurse call system so the alarm is transmitted around the building.This simple-to-use monitor comes with a fixing bracket for easy mounting to the bed frame or door a 2m nurse call connection cable and 1 9V battery. Optional mains PSU also available.Key FeaturesLow battery indicatorPerfect for clients unable to use traditional sensor matsCan be installed anywhere - no wiring requiredQuick and easy to move aroundOptional mains PSU available

GBP 107.29
1

Hochiki HCP-WMSCI Addressable Marine Weatherproof Call Point with SCI

Hochiki HCP-WMSCI Addressable Marine Weatherproof Call Point with SCI

Hochiki HCP-WMSCI Addressable Marine Weatherproof Call Point with SCIThe HCP-WMSCI is a weatherproof Manual Call Point with integral short-circuit isolator which is fully compatible with Hochikis ESP analogue addressable protocol. The unit incorporates a bi-coloured LED which can be selected as pulsingnon-pulsing 1 for communications polling and is continuously lit when the HCP-WMSCI is operated in these two states the LED will show red. The LED will show amber when a short-circuit is present but will switch to red if the unit is activated.The unit operates by pressing the EN54 compliant non-frangible plastic element and produces a high level ESP interrupt. A built in test function initiated by the control panel ensures the integrity of the device at all times and the device can be tested by insertion of a test key in the underside of the unit. Two terminal blocks are provided for easy connection to the loop wiring. The unit is addressed using the TCH-B200 Hand Held Programmer for quick and reliable addressing. An optional glass element is also available.Key FeaturesFast responseIntegral short-circuit isolatorBi-coloured status LEDNon-frangible element fitted as standard conforms to EN54Addressed with TCH-B200 Hand Held ProgrammerSurface mountedIP67 ratedLPCB approved to EN54GL and MED Type approval

GBP 162.67
1

C-Tec QT645 Quantec PIR Power Interface with Isolating Key Switch

C-Tec QT645 Quantec PIR Power Interface with Isolating Key Switch

C-Tec QT645 Quantec PIR Power Interface with Isolating Key SwitchAllows up to two QT638 PIR movement sensors to be connected to a Quantec addressable call system. Connects to the slave input on a QT602 or QT609 Range Call Point. Typically located outside a bedroom where for example two PIRs are beingused to monitor a patient getting out of bed. Includes an isolation key switch so staff entering the room can temporarily disable the PIRs from triggering a call.Key FeaturesDerives its power from the Quantec networknoneed for a separate power supply unitA maximum of16 QT645s can be connected to a Quantec system.Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 90.38
1

Nursecall Intercall 915 Room Control Point

Nursecall Intercall 915 Room Control Point

Nursecall Intercall 915 Room Control PointThe Safeguard point is used to control the monitoring functions within a bedroom.Its sleek wall mounted design allows this unit to be either positioned either side of a bedroom door for simple staff operation. The Safeguard Point is used to alert staff to a resident getting out of bed or opening the bedroom door.These alarm levels are programmable to indicate the type of response required according to individual requirements. The control buttons are operated by authorised staff with an Intercall Care Card. Staff movement and actions are captured on the Intercall data log system allowing full accountability.A built-in reassurance LED and LCD screen provide staff an immediate visual indication of the rooms status.

GBP 141.83
1

SAS NET205M Patient Call Unit with Alarm amp Crash Call Facilities Push Button Reset

SAS NET205M Patient Call Unit with Alarm amp Crash Call Facilities Push Button Reset

SAS NET205M Patient Call Unit with Alarm Crash Call Facilities Push Button ResetUsually located at each bed-head they feature a large orange button which is used by patients when in need of assistance. Staff attending a call can raise a more urgent staff-to-staff call to summon help if necessary and a third call level crash call can be used for medical emergencies. They have a socket for a push-to-call extension lead NET206 that is monitored in case the lead is pulled out from its socket inadvertently.The staff operations are carried out using push buttons on this version. The blue reset button can also be used to log a visit to a room and also register the nurses presence within the room. A reassurance light is illuminated red to reassure a call has been made and green to inform the patient that staff are on their way.The Nursecall System helps patients and staff to relax in the knowledge that should help be required either by the patient or by a member of staff assistance can be directed to the specific room at the touch of a button.

GBP 115.84
1

STI AP-1-R-B Alert Point - Red Fire Text

STI AP-1-R-B Alert Point - Red Fire Text

STI AP-1-R-B Alert Point - Red Fire TextSTIs Alert Point AP-1-R-B is a battery powered stand-alone fire alarm equipment incorporating a resettable call point and an integral sounder.The simple 4 screw installation with no need of wiring ensures that the Alert Point is ideal for small offices portacabins car parks Bed Breakfasts and churches.When activated the Alert Point sends out a 95-102dB alarm and the built in LED flashes red in order to signalise the alarm. In addition external connected devices for example sounders or strobes will be activated. For resetting the device a special key can be used so no parts have to be replaced after activation. Using the override facility the alarm can be set to mute until the Alert Point can be reset.Key FeaturesStand Alone Alarm SystemRobust Polycarbonate Housing including Tamper Switch against mis-usageSimple Installation No wiring involvedPowered with 9V PP3 Battery included1230V dc External Power Facility to support external devicesLow Battery WarningResettable Call Point using key to resetSounder Output 102 dB at 1m output and duration options availableSystem Healthy Fault and Alarm LED indicationActivation Identification LEDPossibility of being interconnected and monitoredColour Red

GBP 118.16
1

STI AP-1-R-A Alert Point - Red - House Flame

STI AP-1-R-A Alert Point - Red - House Flame

STI AP-1-R-A Alert Point - Red - House FlameSTIs Alert Point AP-1-R-A is a battery powered stand-alone fire alarm equipment incorporating a resettable call point and an integral sounder.The simple 4 screw installation with no need of wiring ensures that the Alert Point is ideal for small offices portacabins car parks Bed Breakfasts and churches.When activated the Alert Point sends out a 95-102dB alarm and the built in LED flashes red in order to signalise the alarm. In addition external connected devices for example sounders or strobes will be activated. For resetting the device a special key can be used so no parts have to be replaced after activation. Using the override facility the alarm can be set to mute until the Alert Point can be reset.Key FeaturesStand Alone Alarm SystemRobust Polycarbonate Housing including Tamper Switch against mis-usageSimple Installation No wiring involvedPowered with 9V PP3 Battery included1230V dc External Power Facility to support external devicesLow Battery WarningResettable Call Point using key to resetSounder Output 102 dB at 1m output and duration options availableSystem Healthy Fault and Alarm LED indicationActivation Identification LEDPossibility of being interconnected and monitoredColour Red

GBP 125.27
1

SAS NET205MPC Net205M with Pull Cord

SAS NET205MPC Net205M with Pull Cord

SAS NET205MPC Net205M with Pull CordThe NET205MPC is a Net205M with Pull Cord.Usually located at each bed-head they feature a large orange button which is used by patients when in need of assistance. Staff attending a call can raise a more urgent staff-to-staff call to summon help if necessary and a third call level crash call can be used for medical emergencies. They have a socket for a push-to-call extension lead NET206 that is monitored in case the lead is pulled out from its socket inadvertently.The staff operations are carried out using push buttons on this version. The blue reset button can also be used to log a visit to a room and also register the nurses presence within the room. A reassurance light is illuminated red to reassure a call has been made and green to inform the patient that staff are on their way.The Nursecall System helps patients and staff to relax in the knowledge that should help be required either by the patient or by a member of staff assistance can be directed to the specific room at the touch of a button.Key FeaturesPull Cord

GBP 136.90
1

C-Tec QT644 Floor Pressure Mat

C-Tec QT644 Floor Pressure Mat

C-Tec QT644 Floor Pressure MatThe QT644 floor pressure mat is designed to alert staff to the prospect of a wandering patient in nursing homes hospitals and other care facilities. Fully compatible with our Quantec and 800 Series call systems the mat is manufactured to a high standard with an attractive grey PVC finish and non-slip rubber base.Key FeaturesDesigned to trigger a call when it detects patient foot pressureTypically located alongside a bed to advise staff of wandering patientsCan be connected to a Quantec addressable call system or an 800 Series conventional call system via a remote jack socketTough durable grey PVC finish with a non-slip rubber baseAttractive high-quality design - ideal for use in all types of care facilityCan be wiped-clean using a non-caustic sanitising solutionMeasures 90cm x 60cm 3ft x 2ft. Approx 5mm deepSupplied with a 2m lead and a normally open right-angled jack plugHelps protect infirm residents and dementia sufferers against potential falls by quickly alerting staff if someone gets out of bedHighly sensitiveSimple and reliable operationCan also be used in low-level access control applicationsExcellent discounts for quantity orders

GBP 112.04
1