307 results (0,17057 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Ziton Alarmline AACUSP Analogue LHD Control Unit Self Programmable

Ziton Alarmline AACUSP Analogue LHD Control Unit Self Programmable

Ziton Alarmline AACUSP Analogue LHD Control Unit Self ProgrammableThe AACUSP is a self-programmable Analogue Liner Heat Detection LHD cable control unit. It provides monitoring for any of the Alarmline II range of LHD sensor cable configuration of alarm and pre-alarm temperatures as well as enabling simple interface to a main fire alarm or BMS system.As well as monitoring the LHD sensor cable for changes in temperature the control unit also monitors for open and short circuit faults along the cable ensuring notification if the cable becomes damaged. It is fitted with its own internal temperature monitor and should the temperature within the controller enclosure reach 100C 212F an alarm will be signalled.Each control unit may have up to 500m 1640ft of LHD sensor cable connected to it acting as a single detection zone. When the LHD sensor cable and the control unit are installed in different areas a suitable interposing cable can be used to make the electrical connection between them.The AACULP provides LED indications as well as an LCD. Internal pushbuttons allow configuration without the need for a PC.Pre-Alarm and Alarm thresholds can be set through simple menu options with no need for any graphs or nomograms. Initial set-up is done by measuring and entering the calibration resistance of the sensor cable removing the need to know the sensor cable length. Volt free changeover contacts are provided inside the control unit for Pre-Alarm and Alarm signaling to a main fire alarm control panel or BMS system. A failsafe opto-isolated phototransistor fault output is also provided. No user controls are provided on the control unit. An isolated input is provided enabling remote reset functionality.Key FeaturesUL521 and CE approval ULULC listedUp to 500m of sensor cable per zoneSeparate pre-alarm and alarm signalsEasy programmable interfaceEnclosure temperature alarmIP66 rated enclosureNo nomograms or charts required

GBP 1080.65
1

FFE Fireray 6010-300 Reflective Beam Detector UL

FFE Fireray 6010-300 Reflective Beam Detector UL

FFE Fireray 6010-300 Reflective Beam Detector ULWith no specialist tools or knowledge needed for installation and operation theFireray One is a standalone beam detector that prioritises ease of installation. Using the Fireray One it couldnt be easier to bring the benefits of beam detection to your application.Key FeaturesOne Minute Auto-Alignment just steer the laser onto the Reflector then at the flick of a switch it aligns itself. 8 times faster than previous detectorsOne person installation everything can be done by one personOne standalone product no specialist tools required minimal prior knowledge and training needed

GBP 730.80
1

Ziton Alarmline AACULP Analogue LHD Control Unit PC Programmable

Ziton Alarmline AACULP Analogue LHD Control Unit PC Programmable

Ziton Alarmline AACULP Analogue LHD Control Unit PC ProgrammableThe AACULP is a PC programmable Analogue Liner Heat Detection LHD cable control unit. It provides monitoring for any of the Alarmline II range of LHD sensor cable configuration of alarm and pre-alarm temperatures as well as enabling simple interface to a main fire alarm or BMS system.As well as monitoring the LHD sensor cable for changes in temperature the control unit also monitors for open and short circuit faults along the cable ensuring notification if the cable becomes damaged. It is fitted with its own internal temperature monitor and should the temperature within the controller enclosure reach 100C 212F an alarm will be signalled.Each control unit may have up to 500m 1640ft of LHD sensor cable connected to it acting as a single detection zone. When the LHD sensor cable and the control unit are installed in different areas a suitable interposing cable can be used to make the electrical connection between them.The AACULP provides LED indications only and requires a PC to configure the control unit.Pre-Alarm and Alarm thresholds can be set through simple menu options with no need for any graphs or nomograms. Initial set-up is done by measuring and entering the calibration resistance of the sensor cable removing the need to know the sensor cable length. Volt free changeover contacts are provided inside the control unit for Pre-Alarm and Alarm signaling to a main fire alarm control panel or BMS system. A failsafe opto-isolated phototransistor fault output is also provided. No user controls are provided on the control unit. An isolated input is provided enabling remote reset functionality.Key FeaturesUL521 and CE approval ULULC listedUp to 500m of sensor cable per zoneSeparate pre-alarm and alarm signalsEasy programmable interfaceEnclosure temperature alarmIP66 rated enclosureNo nomograms or charts required

GBP 873.72
1

Talentum Air Purge for Exd Housing 12555

Talentum Air Purge for Exd Housing 12555

Talentum Air Purge for Exd Housing 12555Whilst the IR2 and IR3 types of Flame Detector can still work with contamination from dust or dirt for example on the sensor window their working range and sensitivity can be reduced. Cleaning the Flame Detector if it is high off the ground may be difficult and or expensive this is where the Flame Detector Air Purge kit comes in.By connecting an Air Line or Compressed Air Cylinder to the Air Purge hose the pressurized air can be used to clean the Flame Detectors sensor window. This can be done as and when required depending of the levels of contamination on the site to keep the Flame Detector working at its maximum capability.

GBP 687.30
1

Notifier Honeywell 30 Watt Music Horn Loudspeaker 582433

Notifier Honeywell 30 Watt Music Horn Loudspeaker 582433

Notifier Honeywell 30 Watt Music Horn Loudspeaker 582433The 2-way music horn DK-MH 30T plus-EN 54 with impact-resistant ABS housing in light grey similar to RAL 7035 and protection class IP 66 complements the series of horn loudspeaker for voice alarm. For more safety it is also equipped with ceramic terminal and thermal fuse.An enormous sound pressure and a convincing music quality likewise as simple and flexible installation with stainless aluminium universal mount. The flexible power adjustment can be easily done on the back side of the loudspeaker 30 W 15 W 75 W 375 W. The DK MH30T plus-EN 54 is also suitable for using in outdoor areas.

GBP 676.54
1

Notifier Honeywell DCS Plus Digital Call Station 583520

Notifier Honeywell DCS Plus Digital Call Station 583520

Notifier Honeywell DCS Plus Digital Call Station 583520The digital call station DCS plus allow the selection of loudspeaker circuits the transmission of voice announcements as well as various gongs and alarms. The digital call station is connectable via a standard CAT5 cable to the VARIODYN D1 control devices DOM and Comprio. All control signals up to four simultaneous audio signals and the power supply are transmitted. This connection can be done by single or redundant cabling up to 300 m away.It can be increased to 20 Kilometers by using fiber-optic cabling. The digital call station DCS plus can be expanded with up to six digital keyboard modules DKM plus whereby the total number of available keys and LEDs increases to 120 per communication station. The function of the microphone and the cable connection is permanently monitored. The DCS plus provides an additional external audio input and output which can be used to connect audio devices such as CD players. A 3 m long CAT5 cable to connect the digital call station to a wall jack is included.Key FeaturesHigh failure safety due to redundant transmission routeCost-effective CAT5 cablingElectret gooseneck microphone with cardioid patternExchangeable gooseneck microphone with protection by using a specific tool to lockunlockPermanent monitoring of the microphone and cableMechanical protection against cable disconnectionBuild-in loudspeaker for monitoring and for intercom operation between other paging stationsIndependent additional audio inputoutput e.g. for audio player12 freely configurable keys with independent programmable LEDs

GBP 1928.22
1

Fireray 5000 Single Detector Pack 100m

Fireray 5000 Single Detector Pack 100m

Fireray 5000 Single Detector Pack 100mThe FIRERAY 5000 motorised auto aligning infrared optical beam smoke detector can now be installed with up to four detector heads per system thus saving on installation time and costs.This innovative system has been designed from the ground up to include pioneering technology that fully addresses the needs of the installer and user both now and in the future.Key BenefitsUp to 2 optical beam detectors per system controllerEasifit Fix SystemGround Level ControlLaser Assisted AlignmentAuto-Optimise Beam AlignmentContamination CompensationBuilding Shift CompensationApproved to EN5412 and UL268

GBP 1078.80
1

Fireray 5000 Auto-Aligning Optical Beam Smoke Detector 50m

Fireray 5000 Auto-Aligning Optical Beam Smoke Detector 50m

Fireray 5000 Auto-Aligning Optical Beam Smoke Detector 50mThe FIRERAY 5000 motorised auto aligning infrared optical beam smoke detector can now be installed with up to two detector heads per system thus saving on installation time and costs.This innovative system has been designed from the ground up to include pioneering technology that fully addresses the needs of the installer and user both now and in the future.Key BenefitsUp to 2 optical beam detectors per system controllerEasifit Fix SystemGround Level ControlLaser Assisted AlignmentAuto-Optimise Beam AlignmentContamination CompensationBuilding Shift CompensationApproved to EN5412 and UL268

GBP 1191.90
1

Fireray 5000 Single Detector Pack 50m

Fireray 5000 Single Detector Pack 50m

Fireray 5000 Single Detector Pack 50mThe FIRERAY 5000 motorised auto aligning infrared optical beam smoke detector can now be installed with up to four detector heads per system thus saving on installation time and costs.This innovative system has been designed from the ground up to include pioneering technology that fully addresses the needs of the installer and user both now and in the future.Key BenefitsUp to 2 optical beam detectors per system controllerEasifit Fix SystemGround Level ControlLaser Assisted AlignmentAuto-Optimise Beam AlignmentContamination CompensationBuilding Shift CompensationApproved to EN5412 and UL268

GBP 948.30
1

Fireray 5000 Auto-Aligning Optical Beam Smoke Detector 100m

Fireray 5000 Auto-Aligning Optical Beam Smoke Detector 100m

Fireray 5000 Auto-Aligning Optical Beam Smoke Detector 100mThe FIRERAY 5000 motorised auto aligning infrared optical beam smoke detector can now be installed with up to two detector heads per system thus saving on installation time and costs.This innovative system has been designed from the ground up to include pioneering technology that fully addresses the needs of the installer and user both now and in the future.Key BenefitsUp to 2 optical beam detectors per system controllerEasifit Fix SystemGround Level ControlLaser Assisted AlignmentAuto-Optimise Beam AlignmentContamination CompensationBuilding Shift CompensationApproved to EN5412 and UL268

GBP 1313.70
1

Notifier Honeywell DCSF12 Firemans Emergency Microphone 12 Buttons 583503.RE

Notifier Honeywell DCSF12 Firemans Emergency Microphone 12 Buttons 583503.RE

Notifier Honeywell DCSF12 Firemans Emergency Microphone 12 Buttons 583503.REIn many installation codes it is necessary to have redundancy in critical signal routes like speaker cables Loop or AB cabling between fire panel and the PAVA system. In some installation codes this includes also the connection to the fire men paging microphone.For very good reason because if the connection to the call station is lost there is no way for any live announcement to people which are potential or actually in high danger. Our paging station also supports redundant cable connection to two separate Comprio not standalone Version of Comprio or DOMs which means its possible to connect two cables CAT5 to one paging station. The digital paging microphone DCSF12 serves for the selection of loudspeaker circuits and for setting off speech announcements as well as various gong or alarm sounds.It features 12 freely configurable keys 13 LED and a handheld microphone. The paging microphone is connected with our DAL Digital Audio Link bus to a Comprio or DOM by means of a standard CAT5 cable. All audio signals and all control signals are transmitted digitally. The function of the digital paging microphone is permanently acoustically monitored. Up to four DAL bus links can be connected to a DOM.Every digital call station in the system can simultaneously generate and receive different voice transmissions and control signals. A digital paging microphone can be offset up to 300 m by means of a CAT5 cable. Extension to a greater distance is possible with fiber optic FO cables - see respective FO converters which are needed additionally. Also a connection with FO cables can be done redundant. If more keys andor LEDs are needed it is possible to add up to six digital key modules DKM18 which allows the increase of the total number of available keys and LEDs to 120 per call station.Key FeaturesHigh failure safety due to redundant transmission routeHand-held microphone with built-in loudspeaker and acoustic microphone monitoringPermanent monitoring of the line to the next interface module24-bit ADDA converter12 freely configurable keysAdditional LED programmable in yellow or redCan be used redundantly as well as non- redundantly

GBP 2068.56
1

Fireray 3000-007 Fireray 3000 Controller

Fireray 3000-007 Fireray 3000 Controller

Fireray 3000-007 Fireray 3000 ControllerThe Fireray 3000 is ideal for applications where line of sight for the IR infra-red detection path is narrow and where the building structure uses reflective surfaces. It has also been designed to be aesthetically pleasing and thus can equally suit modern architectural buildings as well as heritage sites particularly where ornate ceilings exist.The Fireray 3000 optical beam smoke detectors together with a battery backed power supply can be connected to a zone of a conventional fire alarm control panel or interfaced to an analogue-addressable system via an addressable input module.The Fireray 3000 has been designed so that it can be installed by one operator with its laser assisted alignment methods combined with easy-to-use alignment LEDs offering a visual feedback. Integrated laser alignment aid can be activated at the controller or at the Receiver head.Key FeaturesAllows for 2 Detectors per System ControllerRange 5 to 120 metres configurable per set of DetectorsIntegral Laser Alignment in Receiver2-wire Interface between Controller and ReceiverSeparate Fire and Fault Relays per DetectorLow Level Controller with LCD displayProgrammable Sensitivity and FireFault delayAutomatic Gain Control AGC for drift compensationFirst Fix concept for Transmitter Receiver and ControllerMultiple cable gland knockouts for ease of wiringTransmitter can be powered from ControllerPatented Light Cancellation Technology LCT cancels unwanted light including sunlight sodium lamps and fluorescent lighting

GBP 1044.00
1

Fireclass 557.202.811FC CPU801 Spare CPU

Fireclass 557.202.811FC CPU801 Spare CPU

Fireclass 557.202.811FC CPU801 Spare CPUThe 557.202.811FC is a CPU801 spare or replacement CPU for Fireclass panels.Enhancing the fire detection system performance capabilities of our FC32 FC64 and FC240 addressable panels CPU801 is a central processing unit that not only increases overall system data handling and processing speeds but also improves the commissioning process. Commissioning is now faster as configuration downloads can be done via USB. The CPU can log up to 10000 system events providing a more comprehensive system report.The CPU801 combines FireClass Express V25.3 software. FireClass Express V25.3 significantly increases programming flexibility and new loop device compatibility. It also supports additional loop devices including the FC410TSM door control module FC420CP-I and FC421CP-I addressable indoor and outdoor call points with isolator and the ANN820 module.Key FeaturesCombines Fireclass Express V25.3 softwareLogs up to10000 system eventsCompatible withFC32 FC64 and FC240 addressable panels

GBP 561.73
1

Aritech ACL800SUW-BCMF-S ACL800 Biometric Capacitive with MIFARE reader - Fingerprint -Wiegand - Surface mount - 9500 Templates - Silver

Aritech ACL800SUW-BCMF-S ACL800 Biometric Capacitive with MIFARE reader - Fingerprint -Wiegand - Surface mount - 9500 Templates - Silver

Aritech ACL800SUW-BCMF-S ACL800 Biometric Capacitive with MIFARE reader - Fingerprint -Wiegand - Surface mount - 9500 Templates - SilverThe ACL800SUW-BCMF is a Wiegand biometric and Mifare reader for access control applications with programmable Wiegand output. It offers storage of up to 9500 fingerprints it reads Mifare Classic 1K 4K Ultralight Desfire cardstags and has a programmable Wiegand Output 24 to 80 bits. Configuration of the readers and fingerprint enrolment is done through the ACL800 BioManager Software.The current ACL800 range is over 10 years old and is due for a refresh. The ACL800 range that consisted out of access readers keypad readers and request-to-exit sensitive pushbuttons has been extended with Biometric readers. There are two models being the swipe and the touch capacitive biometric sensors. They are available in any combination of biometric swipe touch capacitive swipe touch capacitive keypad swipe touch capacitive proximity reader swipe touch capacitive Mifare reader.The Wiegand devices are ideal to be networked by using the TCP IP to RS485 converter ACL800FL-CONV-W. Up to 31 Wiegand devices can be daisy chained over RS485 and are managed by the ACL800 BioManager. When you need more devices then simply add another converter. The access rights can be uploaded from the ACL800 BioManager to all the Wiegand devices connected to the converter. You have the option to either store the fingerprint templates in the reader or on the credential for privacy reasons.Fingerprint and reader management software for biometric readers when used with third party access control systems. Fingerprint enrolment is done from any networked biometric reader or from a USB desktop enrolment unit. The fingerprints could be sent to one or all biometric readers in the network. ACL800 BioManager is a free application and also manages the access levels. Compatible with Windows 7 Windows 8 and Windows 10.Key FeaturesIndooroutdoorDust proof and water-resistant IP65Attractive and timeless designIncludes a buzzerTri-color LEDsSurface mountBacklight illuminationTwo-factor authenticationBiometric fingerprint reader with Mifare card

GBP 684.67
1

Aritech ACL800SUW-BC-S ACL800 Biometric Capacitive Reader Fingerprint Wiegand - Surface Mount - 9500 Templates - Silver

Aritech ACL800SUW-BC-S ACL800 Biometric Capacitive Reader Fingerprint Wiegand - Surface Mount - 9500 Templates - Silver

Aritech ACL800SUW-BC-S ACL800 Biometric Capacitive Reader Fingerprint Wiegand - Surface Mount - 9500 Templates - SilverACL800SUW-BSPX is a Wiegand biometric and Proximity 125kHz reader for access control applications with programmable Wiegand output. It offers storage of up to 100 fingerprints it reads EM HID and Casi Rusco cardstags and has a programmable Wiegand Output 24 to 80 bits. Configuration of the readers and fingerprint enrolment is done through the ACL800 BioManager Software.The current ACL800 range is over 10 years old and is due for a refresh. The ACL800 range that consisted out of access readers keypad readers and request-to-exit sensitive pushbuttons has been extended with Biometric readers. There are two models being the swipe and the touch capacitive biometric sensors. They are available in any combination of biometric swipe touch capacitive swipe touch capacitive keypad swipe touch capacitive proximity reader swipe touch capacitive Mifare reader.The Wiegand devices are ideal to be networked by using the TCP IP to RS485 converter ACL800FL-CONV-W. Up to 31 Wiegand devices can be daisy chained over RS485 and are managed by the ACL800 BioManager. When you need more devices then simply add another converter. The access rights can be uploaded from the ACL800 BioManager to all the Wiegand devices connected to the converter. You have the option to either store the fingerprint templates in the reader or on the credential for privacy reasons.Fingerprint and reader management software for biometric readers when used with third party access control systems. Fingerprint enrolment is done from any networked biometric reader or from a USB desktop enrolment unit. The fingerprints could be sent to one or all biometric readers in the network. ACL800 BioManager is a free application and also manages the access levels. Compatible with Windows 7 Windows 8 and Windows 10.Key FeaturesIndooroutdoorDust proof and water-resistant IP65Attractive and timeless designIncludes a buzzerTri-color LEDsSurface mountBacklight illuminationTwo-factor authenticationBiometric fingerprint reader with proximity card

GBP 576.12
1

Global Fire CHAMELEON-REP Chameleon Control Repeater cw RS422 Network Card

Global Fire CHAMELEON-REP Chameleon Control Repeater cw RS422 Network Card

Global Fire CHAMELEON-REP Chameleon Control Repeater cw RS422 Network CardThe CHAMELEON REP is the best solution when you need full control of a networked system. In a Chameleon Network the CHAMELEON REPEATER is used as a System Repeater.It works as an addressed networked control panel without loops and has the ability to process and register Event-log all system info.For connection diagrams and project commissioning please refer to the Chameleon Network manual as well as the manual of the Communication Interface being used.The graphical backlit LCD display can accommodate any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.The CHAMELEON REP is supplied without battery management capability. It is intended to be connected to an external power supply.The Cause-and-Effect programming of the whole system as well as all customer specific configuration can be downloaded or uploaded using the CHAMELEON CONNECTOR software and later broadcast to other networked control panels.Key FeaturesNetwork Compatibility with the OCTO NODE and GEKKO range of control panelsConnection to the control panels via RS422 Fibre-Optic or TCPIPEvent log 10000 eventsBacklit graphical LCD display of 240 x 64 pixelsProgramming by integrated keypad or Loader PC softwareMultiple language support menu selectable.

GBP 462.80
1

Global Fire CHAMELEON-REPBLK Chameleon Control Repeater cw RS422 Network Card - Black

Global Fire CHAMELEON-REPBLK Chameleon Control Repeater cw RS422 Network Card - Black

Global Fire CHAMELEON-REPBLK Chameleon Control Repeater cw RS422 Network Card - BlackThe CHAMELEON REP is the best solution when you need full control of a networked system. In a Chameleon Network the CHAMELEON REPEATER is used as a System Repeater.It works as an addressed networked control panel without loops and has the ability to process and register Event-log all system info.For connection diagrams and project commissioning please refer to the Chameleon Network manual as well as the manual of the Communication Interface being used.The graphical backlit LCD display can accommodate any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.The CHAMELEON REP is supplied without battery management capability. It is intended to be connected to an external power supply.The Cause-and-Effect programming of the whole system as well as all customer specific configuration can be downloaded or uploaded using the CHAMELEON CONNECTOR software and later broadcast to other networked control panels.Key FeaturesNetwork Compatibility with the OCTO NODE and GEKKO range of control panelsConnection to the control panels via RS422 Fibre-Optic or TCPIPEvent log 10000 eventsBacklit graphical LCD display of 240 x 64 pixelsProgramming by integrated keypad or Loader PC softwareMultiple language support menu selectableColour Black

GBP 487.16
1

Haes LCD Fully Functional Remote Display Unit XL-RDU

Haes LCD Fully Functional Remote Display Unit XL-RDU

Haes LCD Fully Functional Remote Display Unit XL-RDUThe XL-RDU 32 way LCD remote display repeater panels have the same easy to use controls and indications as the main control panels with the addition of a 4 line x 40 character backlit LCD display. The remote display units are fully functional with Silence Resound and Reset controls as well as Disable and Test Mode functions. It is also possible to disable the controls for each or all repeater panels to make them passive indication only. Up to 8 repeater panels can be supported on a system.The display text is fully editable for system panel and zone names plus up to 40 characters for installationservice company details. Other local options include setting the real time clock editing the user access code and lowering or muting the internal buzzer. All programming can be done using the on board controls and user menu or via the PC config software supplied. The main circuit board has 2 switch ve outputs which provide fire and fault signals. Inputs are available for use as PSU fault inputs. An input for a remote key-switch is also provided.Controls are enabled via a 4 digit code entry. The user code can be changed in the programming settings. An eight button keypad is used to control the system and allow access to the function options. The remote display unit is housed in a robust sheet steel enclosure suitable for wall mounting. Cable entry is via 20mm knockouts located at the top and rear of the cabinet. A nominal 28v dc supply is required to power the remote display units which can be obtained from the control panel or remote power supply unit.Key Features4 x 40 character backlit LCD displaySimple colour coded buttons for controlsProgrammable display textRemote key switch inputFull system controlTest mode disablement functionsFully functional or passiveUp to 8 units supported on a systemPC programming software

GBP 499.37
1

Kidde FP2864C-99 2000 Series - Addressable Fire Panel with 2 to 8 loops 16 - 64 Zones - English UK

Kidde FP2864C-99 2000 Series - Addressable Fire Panel with 2 to 8 loops 16 - 64 Zones - English UK

Kidde FP2864C-99 2000 Series - Addressable Fire Panel with 2 to 8 loops 16 - 64 Zones - English UKThe FP2864C is a versatile addressable fire panel supplied with 2class-A loops. In addition to a generous backlit LCD display itprovides LEDs for indicating both fire and fault conditions with textdescriptions for 16 fire zones on the front panel user interface. Thepanel may be upgraded with an additional 6 class-A loops as well as48 zone indicators full inter-panel networking facilities on both copperor fibre as well as with a LON network bus that supports the AritechLON700 devices and repeaters amongst others.The FP2864C provides extensive maintenance features boastspowerful IO programming and supports both Aritech 2000 and 900series protocols.The FP2864C offers multiple auto-configuration options with extensiveauto detection facilities facilitating quick initial setup even for largesystems. Multiple repeaters in various formats may be connected overa 2-wire network with both class-A and B operating modes whilst up to31 fire panels may be networked together for large applications.In addition to the comprehensive information LEDs the panels largeLCD display allows for every device in the system to be described withup to 80 characters of descriptive text as well as 40 characters forzone descriptions. Complete statistics and graphics indications forevery device are available.Several mechanisms for preventing false alarms including floatingbackground with automatic compensation double knock andcoincidence mode within and between zones as well as soak testfacilities allow the user complete piece of mind.Key FeaturesConfiguration maintenance and graphic PC software supportUp to 128 device addresses per loopFull interpanel network optionsFull range of repeaters and LON700 devices including Dutch andScandinavian fire brigade panels and Scandinavian alarm delay unitsNetworkable black box panelsPower supply for 72-hour autonomyDefault start-up and service modesProgrammable service reminders on-line diagnostics and statisticsMaintenance warnings and soak testing faciltiesOne-man maintenanceFloating background and drift compenstationProgrammable daynight functionalityCoincidence within and between zonesTimed and manual zone controlIO programming with Boolean functions maximum allocated input memory 300Scandinavian variants with Scandinavian firemans key availableEN54 and CPD certified

GBP 2294.45
1

Global Fire OCTO-4 Loop Control Panel

Global Fire OCTO-4 Loop Control Panel

Global Fire OCTO-4 Loop Control PanelThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable Chassis

GBP 1446.26
1

Global Fire OCTO-2 OCTO 2 Loop Control Panel

Global Fire OCTO-2 OCTO 2 Loop Control Panel

Global Fire OCTO-2 OCTO 2 Loop Control PanelThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable Chassis

GBP 1157.02
1

Global Fire Equipment OCTO-4BLK 4 Loop Control Panel - Anthracite

Global Fire Equipment OCTO-4BLK 4 Loop Control Panel - Anthracite

Global Fire Equipment OCTO-4BLK 4 Loop Control Panel - AnthraciteThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable ChassisBlack version

GBP 1518.88
1

Global Fire OCTO-2BLK OCTO 2 Loop Control Panel - Black

Global Fire OCTO-2BLK OCTO 2 Loop Control Panel - Black

Global Fire OCTO-2BLK OCTO 2 Loop Control Panel - BlackThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable ChassisColour Black

GBP 1219.99
1