15 results (0,12606 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Vesda VRT-200 Remote Mount Display for VLP with Remote Termination Card 7 Relays

Vesda VRT-200 Remote Mount Display for VLP with Remote Termination Card 7 Relays

Vesda VRT-200 Remote Mount Display for VLP with Remote Termination Card 7 RelaysThe VRT-200 is a LaserPLUS Display Module with Remote Termination Card 7 Relays.Display modules provide real-time indication of the status of a VESDA detector. They have a 20-segment vertical bar graph display a 2 digit numeric display an audible sounder clear alarm and fault indicators. They also have 4 push button keys to control the detector and the mode of the display.The Display Module can be mounted into a detector unit a remote mounting box or a 19in sub rack. Several displays can be configured to display information from a single detector in multiple locations. There are various versions of the display module depending on the type of detector and the relay configuration required. The LaserSCANNER display has a fourth mode for the Numerical Display which shows the First Alarm SectorFAS this being the number of the sector pipe that has detected smoke. For the LaserCOMPACT the Fire 2 LED is omitted. Smoke levels are continuously shown on a bar graph display where each illuminated segment indicates the current level of detected smoke.The top segment of the bar graph indicates the Fire 1 smoke threshold level and each segment below that level represents 120 of the Fire 1 smoke threshold level. To the left of the bar graph are the Fire 1 Action and Alert smoke threshold indicators. At a glance these provide a visual representation of the programmable alarm thresholds showing how close the smoke level is to triggering the next level of alarm.High intensity flashing LEDs provide a clear indication of the fire condition and are accompanied by an audible warning appropriate to the alarm condition. Similarly any fault condition is indicated by a series of LEDs and an audible tone providing a comprehensive range of status information. The audible warning is easily silenced by pressing the Silence button at which point any flashing LEDs are illuminated until the cause of the event is identified rectified and the system reset.Four large tactile push button keys enable users to reset isolate or silence the detector and control the mode of the display module. The buttons can be disabled to prevent operation of its functions. A lamp test routine is initiated by pressing the Mode key for two seconds. A Manual Scan can be initiated on the LaserSCANNER by holding the Silence button for 2 seconds.Key Features7 RelaysProvides Immediate Status Reporting for a Single VESDA Zone.Allows Zone Control of Assigned VESDA Detector.High Intensity Alarm LEDs.Remote Relay Option.20-Segment Vertical Bar Graph Display.Alarm Threshold Indicators.Built-In Sounder for Audible Warning.Comprehensive Fault Reporting.Multi-mode Numeric Display defaults to smoke obscuration.Recessed Mounting Option.

GBP 984.44
1

Vesda VHX-1400 Metal Box HLI Modbus Type 1

Vesda VHX-1400 Metal Box HLI Modbus Type 1

Vesda VHX-1400 Metal Box HLI Modbus Type 1The VESDA Wall-mounted ModBus High Level Interface HLI links your VESDAnet with PC software monitoring tools Building Management Systems BMSs or Fire Alarm Control Panels FACPs otherwise known as host that support the ModBus protocol. There are two models availableWall-mounted ModBus HLI Type 1 VHX-1400 which echoes each character received on the RS232 link back to the host together with reply message.Wall-mounted ModBus HLI Type 2 VHX-1410 which has the echoing function disabled.One ModBus HLI is used to interface to a VESDAnet. Modbus HLI supports up to a maximum of 40 VESDA detectors on a VESDAnet.The Modbus HLI supports VESDAnet detector zone numbers between 1 to 200. The Modbus HLI divides up the address range into to 7 logical networks. For example the first 30 addresses are considered in network 1 addresses between 31 to 60 are in network 2 and so on.Information available using the VESDA Modbus HLIDetector Type VLP VLS VLC VLF.Fault Status Head Battery and Mains Flow Scanner2 .Detector Alarm State Alert Action Fire.Smoke LevelSmoke Bargraph LevelDetector Alarm thresholds Alert Action FireReset DetectorIsolate DetectorStart Scan Test2

GBP 2443.61
1

Vesda VHX-1410 Metal Box HLI Modbus Type 2

Vesda VHX-1410 Metal Box HLI Modbus Type 2

Vesda VHX-1410 Metal Box HLI Modbus Type 2The VESDA Wall-mounted ModBus High Level Interface HLI links your VESDAnet with PC software monitoring tools Building Management Systems BMSs or Fire Alarm Control Panels FACPs otherwise known as host that support the ModBus protocol. There are two models availableWall-mounted ModBus HLI Type 1 VHX-1400 which echoes each character received on the RS232 link back to the host together with reply message.Wall-mounted ModBus HLI Type 2 VHX-1410 which has the echoing function disabled.One ModBus HLI is used to interface to a VESDAnet. Modbus HLI supports up to a maximum of 40 VESDA detectors on a VESDAnet.The Modbus HLI supports VESDAnet detector zone numbers between 1 to 200. The Modbus HLI divides up the address range into to 7 logical networks. For example the first 30 addresses are considered in network 1 addresses between 31 to 60 are in network 2 and so on.Information available using the VESDA Modbus HLIDetector Type VLP VLS VLC VLF.Fault Status Head Battery and Mains Flow Scanner2 .Detector Alarm State Alert Action Fire.Smoke LevelSmoke Bargraph LevelDetector Alarm thresholds Alert Action FireReset DetectorIsolate DetectorStart Scan Test2

GBP 2443.61
1

Vesda VHX-0200 PC Link High Level Interface HLI Complete With Leads

Vesda VHX-0200 PC Link High Level Interface HLI Complete With Leads

Vesda VHX-0200 PC Link High Level Interface HLI Complete With LeadsThe VESDA High Level Interface HLI links your VESDAnet with PC software monitoring and configuring tools such as Xtralis VSM4 and Xtralis VSC. To configure and monitor devices on VESDAnet your HLI must be connected to a VESDAnet socket card.Direct Access to the NetworkBy interfacing with PC monitoring and configuring tools the Sliding Windows HLI allows you to easily configure manage and monitor your entire VESDA network.Simple Configuration and Seamless Data TransferYour HLI is easily configured using your Xtralis VSC or Xtralis VSM4 software packages. The Sliding Windows model provides seamless data transfer from your VESDAnet to your PC.Designed for Small or Large NetworksVESDA Sliding Windows HLIs are designed to suit your individual system design. The VHX-0210 is ideally suited for small networks of up to 40 devices while the VHX-0200 is designed for large networks of up to 200 devices.Modem SupportThe VHX-0210 has modem dial-in or dial out capabilities allowing you full remote notification and interrogation functionality on networks of up to 40 devices.Key FeaturesDirect access and monitoring of your entire VESDAnet systemDesigned for small or large networks VHX-0210 includes modem support for remote notification interrogationSeamless data transfer from your VESDAnet to your PCEasily configured using Xtralis configuring and monitoring software packages

GBP 845.05
1

Vesda VHX-1200 VESDAnet Socket with HLI in Metal Enclosure

Vesda VHX-1200 VESDAnet Socket with HLI in Metal Enclosure

Vesda VHX-1200 VESDAnet Socket with HLI in Metal EnclosureThe VESDA Wall-Mounted High Level Interface HLI links your VESDAnet with PC software monitoring and configuring tools such as Xtralis VSM4 and Xtralis VSC. The HLI includes a built-in VESDAnet socket card.Direct Access to the NetworkBy interfacing with PC monitoring and configuring tools the Wall-mounted HLI allows you to easily configure manage and monitor your entire VESDA network. The built-in VESDAnet socket card makes the Wall-mounted HLI a cost effective solution to your interface requirements. The Wall-mounted HLI receives its voltage supply of 24VDC from the VESDAnet socket card. Therefore an additional power supply is not required.Remote InstallationConnecting to your VESDAnet is easy and convenient because the wall-mounted HLI does not need to be mounted near an VESDA smoke detector. The wall-mounted HLI can be mounted in an easy-to-access remote location away from your detectors such as on a wall near your PC.Simple Configuration and Seamless Data TransferYour HLI is easily configured using your PC and Xtralis VSC or Xtralis VSM4 software packages. The Wall-mounted HLI VHX-1200 provides seamless data transfer from your VESDAnet to your PC.Key FeaturesDirect access and monitoring of your entire VESDAnet systemBuilt-in VESDAnet Interface socket card provides communication and power to the HLIConvenient wall-mounted designSeamless data transfer on networks of up to 200 VESDA devicesEasily configured using Xtralis configuring and monitoring software packages

GBP 1222.97
1

Xtralis OSID Emitter High Power Wired 24 Vdc OSE-HPW

Xtralis OSID Emitter High Power Wired 24 Vdc OSE-HPW

Xtralis OSID Emitter High Power Wired 24 Vdc OSE-HPWOpen-area Smoke Imaging DetectionOSID provides projected beam smoke detectiontechnology. By using advanced dualwavelength projected beams andoptical imaging technology for earlywarning smoke detection OSIDprovides a low-cost reliable andeasy-to-install solution that overcomestypical beam detection issues such asfalse alarm incidents and alignmentdifficulties.Key FeaturesMaximum detection range of 150 m 492 ft for the OSI-10Maximum detection range for CPR approved products is 200 m 656 ftDual wavelength LED-based smoke detectionOptical imaging with CMOS imaging chipOn-board event log for fault and alarm diagnosticsHigh tolerance to false alarm due to building movementHigh tolerance to transient dust steam and intrusion of solid objectsEasy alignment with large adjustment and viewing anglesNo need for precise alignmentTolerant of alignment driftAutomatic commissioning in under ten minutesSimple DIP switch configurationSimple and easy maintenance requirementsThree selectable alarm thresholdsStatus LEDs for Fire Trouble and PowerConventional alarm interface for straightforward fire system integration3-D Volumetric CoverageA significant benefit of OSID is its ability to provide volumetric coverage. As many as seven emitters can be placed within the field of view of a single imager each placed at different heights. The OSID imagers large viewing angles both horizontal and vertical enable three-dimensional area coverage for design flexibility and additional deployment savings. Unlike other volumetric technologies OSID delivers absolute calibration for consistent detection performance regardless of lighting conditions smoke colour airflows or other environmental conditions.ApplicationsLarge open spaces where high-sensitivity detection is not the priority but reliable easy detection is essential includingAirportsTrain stationsShopping centresStadiumsHotels convention centres and office buildingscomplexesEntertainment venuesWarehouses and production floors

GBP 326.59
1

Vesda Xtralis 020-055 19quot Enclosure for Sub-Rack 5 Rows

Vesda Xtralis 020-055 19quot Enclosure for Sub-Rack 5 Rows

Vesda Xtralis 020-055 19 Enclosure for Sub-Rack 5 Rows19 Subrack and Detector Enclosures to complement the VESDA range of detectors displays and programmers a range of glass fronted enclosures are available.The 19-inch rack enclosures are designed to house up to 20 display and programmer modules in a wide variety of configurations to suit the particular requirements of a site where centralised control and monitoring of the VESDA system is required. Two versions are available 2 rack up to 8 Modules and 5 rack up to 20 Modules.19 Subracks ordered separately as VSR-xxxx are mounted on a swing frame for convenient connection of all the cables. Cable entry for 24VDC power VESDAnet connection and interfacing to the relays is provided by a removable gland plate which is drilled as required on site. 19 Subracks and 3U blank panels must be ordered separately.Detector or single remote display EnclosureA detector enclosure is also available which incorporates a small glass window to view an on-board display.This detector enclosure enables a single detector or remote module to be installed in challenging environments where a high IP rating is required.The enclosure can accommodate a single VESDA VLP VESDA VLS VESDA VLC or VESDA VLF detector or a single remote module such as a VRT-200. It is supplied with all appropriate cable and pipe entries pre-drilled for each device and enough plugs to blank off those holes not used.A kit of pipe fittings and instructions is supplied to ensure that the IP rating of the enclosure is maintained but cable glands are NOT supplied as they depend on the cable to be used.

GBP 2294.89
1

Vesda VHX-0410 Modbus HLI for Darwish amp Honeywell Only

Vesda VHX-0410 Modbus HLI for Darwish amp Honeywell Only

Vesda VHX-0410 Modbus HLI for Darwish Honeywell OnlyThe VESDA ModBus High Level Interface HLI links your VESDAnet with PC software monitoring tools Building Management Systems BMSs or Fire Alarm Control Panels FACPs otherwise known as host that support the ModBus protocol. There are two models availableModBus HLI Type 1 VHX-0400 which echoes each character received on the RS232 link back to the host together with reply message.ModBus HLI Type 2 VHX-0410 which has the echoing function disabled.Key FeaturesDirect access and monitoring of your VESDAnet system.Seamless data transfer.Easily configured using Xtralis configuring and monitoring software packages.DescriptionOne ModBus HLI is used to interface to a VESDAnet. Modbus HLI supports up to a maximum of 40 VESDA detectors on a VESDAnet.The Modbus HLI supports VESDAnet detector zone numbers between 1 to 200. The Modbus HLI divides up the address range into to 7 logical networks. For example the first 30 addresses are considered in network 1 addresses between 31 to 60 are in network 2 and so on.Smoke and Alarm LevelsThe Smoke Level is reported relative to the Fire Alarm threshold where the full scale is 20. For example if the Fire Alarm threshold is 0.5 obsm a level of 0.1obsm is reported as 4. In other words the Actual Smoke level Reported smoke value Fire1 Threshold 20.FaultsAll VESDAnet faults are mapped on one or more of the Modbus HLI faults which are listed belowHead FaultHead Fault Battery and MainsHead Fault Scanner2 and Flow FaultVESDAnet faults categorised as network faults are mapped onto all zones whereas zone faults are mapped onto that particular zone.

GBP 1328.53
1

Vesda Xtralis OSID Emitter Wired 24Vdc OSE-SPW

Vesda Xtralis OSID Emitter Wired 24Vdc OSE-SPW

Xtralis OSID Emitter Wired 24Vdc OSE-SPWThe OSE-SPW is used as a preferred solution when 24 Vdc is close by.The company that revolutionized very early warning smoke detection with VESDA has reinvented smoke detection for open spaces with Open-area Smoke Imaging Detection OSID. OSID by Xtralis provides reliable cost-effective smoke detection for open spaces where fire detection presents unique challenges and where very early warning is not always the priority.In its simplest configuration OSID by Xtralis uses one imager a camera-like device with a wide field of view and a wired or battery-powered emitter roughly aligned on the opposite wall within the protected area. The emitter sends both infrared and ultraviolet coded light signals to the imager. If the light reception is altered due to the presence of genuine smoke particles the imager will go into alarm. The novel use of dual light frequencies in an open-path device enables OSID to discriminate between real smoke and other objects including insects steam condensation and dust thus drastically reducing false alarms.Key FeaturesOSIDs uncompromising performance is based on the patented use of digital imaging dual-frequency beams and smart algorithms deliveringPatented dual wavelength UV IR particle detectionCMOS Imager with wide viewing anglesSimple installation commissioning and maintenanceHigh tolerance to vibration and structural movementHightolerance to dust fogging steam reflections and object intrusionHigh resistance to reflected sunlightOn-board log memorySoftware tool for diagnostic purposesAesthetically discreet and 3D coverageLong range up to 150 m. 492 ft. with minimal free space 15 cm.5.85ApplicationsOSID is ideal for use in a wide range of industries and applications. These include atriums domes and large rooms inAirportsTrain stationsShopping centresStadiumsEducational facilitiesHotels convention centres and office buildingscomplexesEntertainment venuesWarehouses and production floors

GBP 326.59
1

Vesda Xtralis OSI-90 Open-area Smoke Imaging Detector - 80 Coverage

Vesda Xtralis OSI-90 Open-area Smoke Imaging Detector - 80 Coverage

Vesda Xtralis OSI-90 Open-area Smoke Imaging Detector - 80 CoverageThe OSI-90 covers a distance of 30 - 150m with the OSE-SPW. This configuration is for a 1 on 1 system and is not suitable to work with high powered emitters.The company that revolutionized very early warning smoke detection with VESDA has reinvented smoke detection for open spaces with Open-area Smoke Imaging Detection OSID. OSID by Xtralis provides reliable cost-effective smoke detection for open spaces where fire detection presents unique challenges and where very early warning is not always the priority.In its simplest configuration OSID by Xtralis uses one imager a camera-like device with a wide field of view and a wired or battery-powered emitter roughly aligned on the opposite wall within the protected area. The emitter sends both infrared and ultraviolet coded light signals to the imager. If the light reception is altered due to the presence of genuine smoke particles the imager will go into alarm. The novel use of dual light frequencies in an open-path device enables OSID to discriminate between real smoke and other objects including insects steam condensation and dust thus drastically reducing false alarms.Key FeaturesOSIDs uncompromising performance is based on the patented use of digital imaging dual-frequency beams and smart algorithms deliveringPatented dual wavelength UV IR particle detectionCMOS Imager with wide viewing anglesSimple installation commissioning and maintenanceHigh tolerance to vibration and structural movementHightolerance to dust fogging steam reflections and object intrusionHigh resistance to reflected sunlightOn-board log memorySoftware tool for diagnostic purposesAesthetically discreet and 3D coverageLong range up to 150 m. 492 ft. with minimal free space 15 cm.5.85ApplicationsOSID is ideal for use in a wide range of industries and applications. These include atriums domes and large rooms inAirportsTrain stationsShopping centresStadiumsEducational facilitiesHotels convention centres and office buildingscomplexesEntertainment venuesWarehouses and production floorsThe OSI-90 Imager is used in multi emitter applications or in shorter distance applications. The appropriate number of OSE-SP-01 OSE-SPW or OSE-HPW Emitters must be paired with the Imager to a maximum of seven.

GBP 691.74
1

Vesda Xtralis OSE-SP-01 OSID-DE Emitter Alkaline Battery

Vesda Xtralis OSE-SP-01 OSID-DE Emitter Alkaline Battery

Vesda Xtralis OSE-SP-01 OSID-DE Emitter Alkaline BatteryEach emitter up to 7 generates 2 light beams in the UV and IR frequencies. These bundles are also encoded through a unique code recognized by the receiver. This approach allows the receiver to ignore any UV and IR light beams that come from sources other than emitters the typical interference problems generated by sunlight are thus overcome.Battery powered emitters last for 3 years.Emitter Size 208 mm x 136 mm x 96 mm. Certificate 3052011 EU - CPR.Open-area Smoke Imaging Detection OSID by Xtralis is a new innovation in projected beam smoke detection technology. By using advanced dual wavelength projected beams and optical imaging technology for early warning smoke detection OSID provides a cost-effective reliable and easy-to-install solution that overcomes typical beam detection issues such as false alarm incidents and alignment difficulties.In its simplest configuration OSID by Xtralis uses one imager a camera-like device with a wide field of view and a wired or battery-powered emitter roughly aligned on the opposite wall within the protected area. The emitter sends both infrared and ultraviolet coded light signals to the imager. If the light reception is altered due to the presence of genuine smoke particles the imager will go into alarm. The novel use of dual light frequencies in an open-path device enables OSID to discriminate between real smoke and other objects including insects steam condensation and dust thus drastically reducing false alarms.Key FeaturesPatented dual wavelength UV IR particle detectionCMOS imager with wide viewing anglesSimple installation commissioning and maintenanceHigh tolerance to vibration and structural movementHigh resistance to dust fogging steam reflections and object intrusionHigh resistance to reflected sunlightOn-board log memorySoftware tool for diagnostic purposesAesthetically discreet and 3D coverageLong range up to 150 m 492 ft. with minimal free space dia. 15 cm 5.85 inchApplicationsOSID is ideal for use in a wide range of industries and applications. These include atriums domes and large rooms inAirportsTrain stationsShopping centresStadiumsEducational facilitiesHotels convention centres and office buildingscomplexesEntertainment venuesWarehouses and production floors

GBP 326.59
1

Vesda Xtralis OSI-10 Open-area Smoke Imaging Detector - 7 Coverage

Vesda Xtralis OSI-10 Open-area Smoke Imaging Detector - 7 Coverage

Vesda Xtralis OSI-10 Open-area Smoke Imaging Detector - 7 CoverageThe OSI-10 covers a distance of 30 - 150m with the OSE-SPW. This configuration is for a 1 on 1 system and is not suitable to work with high powered emitters.The company that revolutionized very early warning smoke detection with VESDA has reinvented smoke detection for open spaces with Open-area Smoke Imaging Detection OSID. OSID by Xtralis provides reliable cost-effective smoke detection for open spaces where fire detection presents unique challenges and where very early warning is not always the priority.In its simplest configuration OSID by Xtralis uses one imager a camera-like device with a wide field of view and a wired or battery-powered emitter roughly aligned on the opposite wall within the protected area. The emitter sends both infrared and ultraviolet coded light signals to the imager. If the light reception is altered due to the presence of genuine smoke particles the imager will go into alarm. The novel use of dual light frequencies in an open-path device enables OSID to discriminate between real smoke and other objects including insects steam condensation and dust thus drastically reducing false alarms.3D Volumetric CoverageA significant benefit of OSID is its ability to provide volumetric coverage. As many as seven emitters can be placed within the field of view of a single imager each placed at different heights. The OSID imagers large viewing angles both horizontal and vertical enable three-dimensional area coverage for design flexibility and additional deployment savings. Unlike other volumetric technologies OSID delivers absolute calibration for consistent detection performance regardless of lighting conditions smoke colour airflows or other environmental conditions.Key FeaturesOSIDs uncompromising performance is based on the patented use of digital imaging dual-frequency beams and smart algorithms deliveringPatented dual wavelength UV IR particle detectionCMOS Imager with wide viewing anglesSimple installation commissioning and maintenanceHigh tolerance to vibration and structural movementHightolerance to dust fogging steam reflections and object intrusionHigh resistance to reflected sunlightOn-board log memorySoftware tool for diagnostic purposesAesthetically discreet and 3D coverageLong range up to 150 m. 492 ft. with minimal free space 15 cm.5.85ApplicationsOSID is ideal for use in a wide range of industries and applications. These include atriums domes and large rooms inAirportsTrain stationsShopping centresStadiumsEducational facilitiesHotels convention centres and office buildingscomplexesEntertainment venuesWarehouses and production floorsThe OSI-10 Imager must be paired with either the OSE-SP-01 or OSE-SPW Standard Power Emitter. The OSI-10 can only support one emitter.

GBP 671.33
1