7 results (0,13775 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Vesda Xtralis White Flexible Connector PIP-026-W

Vesda Xtralis White Flexible Connector PIP-026-W

Vesda Xtralis White Flexible Connector PIP-026-WFlexible connectors are installed where a bend or elbow is not suitable. They are reinforced internally with a steel wire for extra strength. They are an ideal fitting as they can be positioned in any direction without restricting the air flow.They should always be connected withABS solvent cement. Available in 30cm and 100cm lengths.Key FeaturesMaterial ABS soft PVC with embedded steel wire reinforcementColour WhiteOperating temperature range -40C to 70CEN54 tested25mmPlease note The PIP-026-W is equivalent to the WHTFLEX-30.

GBP 19.28
1

Vesda Xtralis WHTFLXI25B 25mm Flexible 1m Long Bend

Vesda Xtralis WHTFLXI25B 25mm Flexible 1m Long Bend

Vesda Xtralis WHTFLXI25B 25mm Flexible 1m Long BendThe WHTFLXI25B is a 25mm Flexible 1m Long Bend.VESDA Aspirating Pipe and Fittings are produced in ABS under a stringent quality control system approved to BS EN ISO 9001 EN54 - 20 and EN61386-1 Class 1131 ABS Acrylonitrile Butadiene Styrene is a robust polymer which has the most suitable physical properties for aspirating detection optimising performance with tensile strength chemical resistance ductility weatherability heat stability and processability.The range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system.The pipes are a metric standard of 25 mm external diameter with suitable adapters available for imperial to metric conversions and are designed for use with any make of low-pressure aspirating type smoke detection system.Key FeaturesEquivalent to PIP-021-W25mm in diameter1 metre length

GBP 29.59
1

Vesda Xtralis M8 Nut - Pack of 10 PIP-029

Vesda Xtralis M8 Nut - Pack of 10 PIP-029

Vesda Xtralis M8 Nut - Pack of 10 PIP-029M8 Nut for fitting clip to the end of threaded rod.VESDA Aspirating Pipe and Fittings are produced in red ABS under a stringent quality control system approved to BS EN ISO 9001 EN54 - 20 and EN61386-1 Class 1131 ABS Acrylonitrile Butadiene Styrene is a robust polymer which has the most suitable physical properties for aspirating detection optimising performance with tensile strength chemical resistance ductility weatherability heat stability and processability.The range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system. They are also manufactured to comply with the requirements of BS5391 Part 1 EN 61386-1 and the new EN54 Part 20 guaranteeing you the quality you are used to as a VESDA customer.Please Note The PIP-029 is equivalent to the ACCPCN025B.

GBP 7.37
1

Vesda Xtralis 25mm10mm Compression Adaptor Pack of 10

Vesda Xtralis 25mm10mm Compression Adaptor Pack of 10

Vesda Xtralis 25mm10mm Compression Adaptor Pack of 10Adaptor Fitting PlainCompression 25mm x 10mm. VESDA Aspirating Pipe and Fittings are produced in red ABS under a stringent quality control system approved to BS EN ISO 9001 EN54 - 20 and EN61386-1 Class 1131 ABS Acrylonitrile Butadiene Styrene is a robust polymer which has the most suitable physical properties for aspirating detection optimising performance with tensile strength chemical resistance ductility weatherability heat stability and processability.The range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system. They are also manufactured to comply with the requirements of BS5391 Part 1 EN 61386-1 and the new EN54 Part 20 guaranteeing you the quality you are used to as a VESDA customer.Key FeaturesMaterial ABSColour RedOperating temperature range -40C to 70CEN54 testedThese adaptors allow for connection of10mm capillary pipetubes to pipe. The plain end is to be glued to the pipe usingABS solvent cement.Please note The PIP-034 is equivalent to the REDADI025A.

GBP 63.50
1

Vesda Xtralis WHTCTII0250-10 25mm10mm White Capillary Tee

Vesda Xtralis WHTCTII0250-10 25mm10mm White Capillary Tee

Vesda Xtralis WHTCTII0250 25mm10mm White Capillary Tee - Pack of 10The WHTCTII0250 is a 25mm10mm White Capillary Tee.VESDA Aspirating Pipe and Fittings are produced in ABS under a stringent quality control system approved to BS EN ISO 9001 EN54 - 20 and EN61386-1 Class 1131 ABS Acrylonitrile Butadiene Styrene is a robust polymer which has the most suitable physical properties for aspirating detection optimising performance with tensile strength chemical resistance ductility weatherability heat stability and processability.The range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system. They are also manufactured to comply with the requirements of BS5391 Part 1 EN 61386-1 and the new EN54 Part 20 guaranteeing you the quality you are used to as a VESDA customer.The pipes are a metric standard of 25 mm external diameter with suitable adapters available for imperial to metric conversions and are designed for use with any make of low pressure aspirating type smoke detection system.Key FeaturesEquivalent to PIP-016-W25mm10mmColour White

GBP 69.18
1

Vesda Xtralis 25mm In-line Expansion Socket 100mm PIP-019

Vesda Xtralis 25mm In-line Expansion Socket 100mm PIP-019

Vesda Xtralis 25mm In-line Expansion Socket 100mm PIP-019These sockets are used in the installation of pipework where buildings may contract or expand or have fluctuation of temperatures. They allow for movement within the pipework while maintaining a sealed connection due to the internal rubber gaskets.VESDA Aspirating Pipe and Fittings are produced in red ABS under a stringent quality control system approved to BS EN ISO 9001 EN54 - 20 and EN61386-1 Class 1131 ABS Acrylonitrile Butadiene Styrene is a robust polymer which has the most suitable physical properties for aspirating detection optimising performance with tensile strength chemical resistance ductility weatherability heat stability and processability.The range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system. They are also manufactured to comply with the requirements of BS5391 Part 1 EN 61386-1 and the new EN54 Part 20 guaranteeing you the quality you are used to as a VESDA customer.Key Features Tech SpecsMaterial ABSColour RedOperating temperature range -40C to 70CLength 100mmEN54 testedPlease Note The PIP-019 is equivalent to the REDEXSOC.

GBP 19.73
1

Vesda OSI-RE-SS OSID R Reflective Beam

Vesda OSI-RE-SS OSID R Reflective Beam

Vesda OSI-RE-SS OSID R Reflective BeamThe Vesda OSI-RE-SS is a 4-wire single-ended reflected type beam smoke detector that includes an 8 reflector and an integral sensitivity test.The Vesda OSI-RE-SS is a reflector-type linear optical beam smoke detector designed to operate as a component of fire alarm systems. The beam operates primarily on the principle of light obscuration utilising an Infra-Red beam. Optical beam smoke detectors are particularly appropriate for protecting buildings with large open spaces such as warehouses atriums etc.The OSI-RE-SS detector is a combined transmitterreceiver unit that can be directly connected to a conventional detector circuit.Key FeaturesCombined transmitter and receiver unit range 5-100 m 16-328 ftConventional modelReceiver consists of a CMOS imaging CCDWide 12 field of viewIntuitive beam alignment indicated by directional arrowsSingle IR wavelengthHighly resistant to building movement tolerates - 1 movementResistant to strong light sources does not alarm when saturated by sunResistant to large solid intruding objectsAutomatic sensitivity threshold level setting50 horizontal and 20 vertical beam alignmentBuilt-in heaterElectronic simulated smoke test from ground levelStandby fault and alarm LED indicators visible from the front and bottomAutomatic drift compensationPaintable coverRemovable plug-in terminal blocksOptional heater kit available for the reflectorThe Infra-Red transmitter and receiver Imager generates a beam of light towards a high efficiency reflector. The reflector returns the beam to the receiver where an analysis of the received signal is made. The change in the strength of the received signal is used to determine the alarm condition.The receiver imager has a wide FOV of 12 and tracks automatically the reflector in case of building movement or movement of its support structure. It is virtually impossible for the receiver to lose the reflector out of its side of view without any structural damage being caused to the building. As a result of this operation the OSI-RE-SS eliminates the number one cause of false alarms andor faults with traditional beam detectors.Optical filtering high-speed image acquisition and intelligent software algorithms provide the OSID-RE system with higher levels of stability and with greater resistance to high level lighting variability. As such the detector has a better resistance to sunlight and intruding objects in its FOV.The detector will not alarm when saturated by sunlight reflected sunlight or any other very bright light sources. In worst case the detector will go in to trouble and hence solving another cause of false alarms with traditional basic photocell receiver beam detectors. Thanks to the smoke imaging techniques the detector will not alarm for partial and sudden blockage.The alignment of the detector is extremely intuitive fast and accurate. Both the IR transmitter and the CMOS imager are contained in the eyeball that can turn freely in all directions. The eyeball moves - 20 in the vertical direction and 50 in the horizontal direction. Four arrows that indicate the direction to move the eyeball will guide the user to find the imagers perfect alignment with the reflector.To get started swiftly at long distances a laser tool can be inserted in the eyeball to allow finding the reflector quickly and then fine-tuning the eyeball to the optimum alignment. Once the optimum alignment is finalised signalled by all green arrows and LED the eyeball is locked by tightening the lever on its side. A paintable cover is then placed over the front to hide the alignment arrows locking mechanism and secures the locking lever in locked position. Unique in the market the sensitivity of the detector is selected and set automatically at the optimum sensitivity based on the size of the reflector measured in the FOV. The detector incorporates automatic drift compensation whereby the detector will adjust its detection thresholds in line with any long term signal reduction of the beam caused by contamination of the optical surfaces. An internal heating option is also provided on the Imager to prevent condensation on the optical surface.

GBP 870.91
1