28 results (0,13864 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Rosewood Fascia Capping Board Joint - 300mm

Rosewood Fascia Capping Board Joint - 300mm

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.46
1

Anthracite Grey Fascia Capping Board Joint - 300mm

Anthracite Grey Fascia Capping Board Joint - 300mm

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.46
1

Golden Oak Fascia Capping Board Joint - 300mm

Golden Oak Fascia Capping Board Joint - 300mm

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.46
1

Black Ash Woodgrain Fascia Capping Board Joint - 300mm

Black Ash Woodgrain Fascia Capping Board Joint - 300mm

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 7.46
1

Rosewood Fascia Capping Board Internal Corner - 300mm

Rosewood Fascia Capping Board Internal Corner - 300mm

Internal corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. Internal corners are usually found at the foot of a valley on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Internal corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 6.96
1

Golden Oak Fascia Capping Board Internal Corner - 300mm

Golden Oak Fascia Capping Board Internal Corner - 300mm

Internal corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. Internal corners are usually found at the foot of a valley on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Internal corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 6.96
1

Black Ash Woodgrain Fascia Capping Board Internal Corner - 300mm

Black Ash Woodgrain Fascia Capping Board Internal Corner - 300mm

Internal corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. Internal corners are usually found at the foot of a valley on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Internal corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 6.96
2

Bullnose Fascia 135 Degree Internal Corner - 327mm x 50mm White

Bullnose Fascia 135 Degree Internal Corner - 327mm x 50mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This corner is 327mm long.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 6.22
1

Bullnose Fascia 135 Degree External Corner - 327mm x 50mm White

Bullnose Fascia 135 Degree External Corner - 327mm x 50mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This corner is 327mm long.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 6.22
1

Bullnose Fascia Double Ended External Corner - 600mm x 40mm White

Bullnose Fascia Double Ended External Corner - 600mm x 40mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This corner is 600mm long, meaning that you can create 2 joints from 1 piece.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 4.78
1

Bullnose Fascia Double Ended Joiner - 600mm x 40mm White

Bullnose Fascia Double Ended Joiner - 600mm x 40mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This joiner is 600mm long, meaning that you can create 2 joints from 1 piece.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 4.78
1

Fascia End Cap - 300mm Storm Grey Smooth

Fascia End Cap - 300mm Storm Grey Smooth

End caps work by sealing off the cellular core of the cut board that is exposed and are commonly used when the fascia boards does not terminate at a corner._x000D_It is recommended to use a hacksaw to trim the end cap to match the fascia board size and fix it in place with superglue._x000D_Freefoamand#039;s fascia end cap is 300mm in length and is coated in a smooth storm grey._x000D_Freefoam fascia_x000D_Available in 6 different sizes ranging from 150mm to 410mm in a wide selection of colours featuring Freefoam patented Colourmax technology._x000D_Freefoamand#039;s fascias are BS EN 13245-2:2008 certified.

GBP 4.81
1

Fascia Bargeboard Finial - 335mm Black Smooth

Fascia Bargeboard Finial - 335mm Black Smooth

Bargeboard finials are a multi-purpose decorative piece used to cover the joint between the two bargeboards at the apex of the roof.The bargeboard system must expand and contract correctly dependant on the temperature. For any PVC fascia installation, it is recommended to glue one side of the finial to the board and seal the other side with low modulus silicon , which allows for movement within the joint.Freefoamand#039;s replacement fascia bargeboard finial is 335mm in length.

GBP 7.42
1

Fascia Bargeboard Finial - 335mm Anthracite Grey Smooth

Fascia Bargeboard Finial - 335mm Anthracite Grey Smooth

Bargeboard finials are a multi-purpose decorative piece used to cover the joint between the two bargeboards at the apex of the roof.The bargeboard system must expand and contract correctly dependant on the temperature. For any PVC fascia installation, it is recommended to glue one side of the finial to the board and seal the other side with low modulus silicon , which allows for movement within the joint.Freefoamand#039;s replacement fascia bargeboard finial is 335mm in length.

GBP 7.42
1

Fascia Bargeboard Finial - 340mm White

Fascia Bargeboard Finial - 340mm White

Bargeboard finials are a more decorative way of covering the joint between the two bargeboards at the apex of the roof.To enable the barge boards to expand and contract correctly in a different range of temperatures, one side of the finial should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.This rule should be always applied to any corner or joint cover on any PVC fascia installation.

GBP 8.23
1

Ogee Fascia Joint Double Ended - 500mm White

Ogee Fascia Joint Double Ended - 500mm White

Fascia joint covers are used to hide the 10mm expansion gap that should be left between two boards.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended joints can be cut to size with a standard hacksaw or fine toothed saw.

GBP 5.73
1

Ogee Fascia Corner Double Ended - 500mm White

Ogee Fascia Corner Double Ended - 500mm White

Corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.andnbsp;Double ended corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 8.02
1