33 results (0,14673 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Notifier Interface IO BS7273-4 Door Release System NFX-DRS-1

Notifier Interface IO BS7273-4 Door Release System NFX-DRS-1

Notifier Interface IO BS7273-4 Door Release System NFX-DRS-1BS7273 part 4 2007 is the code of practice governing door holders and door release mechanisms. The NFXDRS-1 system offers a compliant solution to meet the requirements of section 5 of BS7273-4 Category Ainstallations by ensuring the failsafe operation of actuation of release mechanisms in conjunction with theexisting output module and wider fire system.The module is compatible with 12-24VDC door hold systems andincludes a volt free contact.The Notifier Door Release System NFX-DRS-1 comprisesDRM-1 door release module M701 single output model and SMB6-V0 surface mount box pre-wired for simple installation.

GBP 168.73
1

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242Four-channel power amplifier with built in battery charger for emergency power supply of VARIODYN D1 Comprio. 4XD125B has 4 independent amplifier channels each with 125 W in class D direct drive technology. Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up.This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power only 4XDxxxB models. The amplifier may be used with the VARIODYN D1 Comprio as well as a DOM. It is also possible to use the amplifier with a separate PSU in this case the internal battery charger must be disabled.Key FeaturesEN 54-4 and EN 54-16 certifiedCompliant with EN 60849 and EN 50849Class D technology efficiency 80 4 independent amplifier channelsOne of four amplifier channels can be used as general back up channelOne height unitIdeal for use with the VARIODYN D1 ComprioSelf-monitoring and self-test by microcontrollerProtected against overload short circuit and overheatingSmooth and fast step-down in 1dB steps in the event of overdrive or over load24 V DC PSU for back up mains powerIntegrated battery charger according to EN 54-4 for charging batteries up to a capacity of 65 Ah 2 x 12 V 65 Ah for emergency power supply of the amplifier and one Comprio or DOMTemperature controlled variable speed fans

GBP 3463.82
1

Notifier NFS 4 Zone Conventional Fire Alarm Panel

Notifier NFS 4 Zone Conventional Fire Alarm Panel

Notifier NFS 4 Zone Conventional Fire Alarm PanelDeveloped with efficiency in mind NFS2-8 zone non-addressable fire alarm panels offer both installers and end users a technically advanced range of functions while remaining easy to install program and operate. A full range of non-addressable detectors advanced non-addressable detectors beam detectors manual call points duct mounting applications audible and visible devices are available for use with the panels.NFS2-8 series fire alarm panels are ideally suited for facilities including offices shop units public houses B B clubs small industrial units nursing homes and schools offering a wide range of benefits to installers and end-users.Key FeaturesCPD approved to EN54-24Simple to installRobust fire resistant ABS moulded enclosureBattery space for up to 72 hour stand-by2 4 or 8 zone versions availableZones configurable for delay coincidence short-circuit alarm capacitor or resistive end of line.Fire and fault outputs - volt-free relay or monitoredAuxiliary power output for ancillary equipment2 configurable inputs for ancillary equipment e.g. class change alert etc.Space for two option modulesOptional 8-way relay module common or zonal switchingOptional 1.5A 4-way sounder module common or zonal switching

GBP 356.93
1

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243Four-channel amplifier with integrated battery recharging system for the emergency power supply to the VARIODYN D1 Comprio. The 4XD250B features 4 independent amplifier channels each with 250 W in class D direct drive technology. Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up.This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power only 4XDxxxB and 4XDxxxW models. The amplifier can be used in combination with the VARIODYN D1 Comprio as well as with a DOM. It is also possible to use the amplifier also with a separate PSU the internal PSU must be switched of then. In this case the internal battery charger must be disabled.Key FeaturesEN 54-4 and EN 54-16 certifiedCompliant with EN 60849 and EN 50849Class D technology efficiency 80 4 independent amplifier channelsOne of four amplifier channels can be used as general back up channelTwo Height Unit 2 HUIdeal for use with the VARIODYN D1 ComprioSelf-monitoring and self-test by microcontrollerProtected against overload short circuit and overheatingSmooth and fast step-down in 1dB steps in the event of overdrive or over load24 V DC PSU for back up mains powerIntegrated battery charger according to EN 54-4 for charging batteries up to a capacity of 65 Ah 2 x 12 V 105 Ah for emergency power supply of the amplifier and one Comprio or DOMTemperature controlled variable speed fans

GBP 5451.26
1

Notifier Honeywell PSU 24V-4 Emergency Power Supply Unit for VAPA System 581723

Notifier Honeywell PSU 24V-4 Emergency Power Supply Unit for VAPA System 581723

Notifier Honeywell PSU 24V-4 Emergency Power Supply Unit for VAPA System 581723Emergency manager for use as emergency power supply of a Voice Alarm application.Key FeaturesEmergency power supply in the 2 HU enclosureOutputs for control devices such as DOM or Comprio net1 individually fused high power outputs for output amplifiers 12 outputs in total but one output cannot be usedAuthorisation pursuant to EN 54-4A2LED displays and display for status reportsPotential-free contacts for the transmission of alarm messagesBattery capacity up to a total of 640 AhMaximum output current in case of emergency power situation 372A

GBP 4500.54
1

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11Power amplifier for the voice alarm system VARIODYN D1 in class D technologies with four independent power channels and galvanic isolated 100 V direct outputs symmetric inputs inrush current limitation and soft start. In comparison to our 4XDxxxB series amplifiers one amplifier can back up another amplifier. Four built-in fans with smooth temperature controlled speed control.Key FeaturesBuilt- in electronic protective circuit against thermal overload DC signals sub frequent signals short circuit open outputs and HF interferenceIndividual status LEDs indicate channel CLIP PROTECT SIGNAL POWER LINE and 24 V DC power Back switch contact for sequential remote power2 back fault message contactsBack fault message contact for missing 24 V emergency power supply24 V emergency power supply inputSuitable for use with loop technology

GBP 4644.12
1

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11Power amplifier for the voice alarm system VARIODYN D1 in class D technologies with four independent power channels and galvanic isolated 100 V direct outputs symmetric inputs inrush current limitation and soft start. In comparison to our 4XDxxxB series amplifiers one amplifier can back up another amplifier. Four built-in fans with smooth temperature controlled speed control.Key FeaturesBuilt- in electronic protective circuit against thermal overload DC signals sub frequent signals short circuit open outputs and HF interferenceIndividual status LEDs indicate channel CLIP PROTECT SIGNAL POWER LINE and 24 V DC power Back switch contact for sequential remote power2 back fault message contactsBack fault message contact for missing 24 V emergency power supply24 V emergency power supply inputSuitable for use with loop technology

GBP 8099.83
1

Notifier Honeywell ABT-M04 Microphone

Notifier Honeywell ABT-M04 Microphone

Notifier Honeywell ABT-M04 MicrophoneThe ABT-M04 is a 4-button analogue microphone with built in gong push to talk and bi-colour LED indicating the ready-to-speak status.To operate the device first select the Zones by pressing designated buttons and then press MIC ON button the status LED will switch from red not ready for broadcast to steady green light. In the event of an active built in gong the status LED will turn green once the gong has ended. When finished transmitting the message release the MIC ON button to deactivate the goose-neck mic.DetailsOperating voltage 2057 VDCEciency 10 mV aOutput level 775 mVMaximum distance from amplier 250 mRecommended cable type UTPConnector Type 8P8C RJ45Dimensions withoutpackaging not more than 150 60 165 mmNet weight not more than 12 kg

GBP 502.86
1

Notifier ID3000 4 Loop Addressable Control Panel with 4.5A Power Supply 020-727

Notifier ID3000 4 Loop Addressable Control Panel with 4.5A Power Supply 020-727

Notifier ID3000 4 Loop Addressable Control Panel with 4.5A Power Supply 020-727The Notifier ID3000 family of fire alarm control panels deliver the power and flexibility to meet the even the most demanding of requirements. From 2 to 8 loops in a single ID3000 panel to over 500 loops on a network an ID3000 system offers unrivalled stability versatility and capacity. When it comes to giving you the earliest possible warning of a potential fire threat the ID3000 supports Notifiers comprehensive range of detectors advanced fire detection sensors and loop devices delivering you the most complete and versatile fire alarm system in the market place.The ID3000 can be programmed to adapt to the different uses of the areas where smoke detectors are installed. A total of 9 different sensitivity levels can be assigned to individual smoke sensors thereby allowing the system designer to closely match the sensors response to the environment in which the device is located. This even allows smoke detection to be turned off leaving heat detection active.Key Features2-8 Analogue Addressable Loops each of up to 198 devices255 Fire zones per panelFully approved peer to peer network of up to 63 panels maintains 3 second call point response time over the networkFlexible timer functions system sensitivity and functionality can be tailored for the time of day or day of weekSophisticated cause and effect programming including support for non-fire signals and over-ride capability for smoke control systems.Convenience features for commissioning and maintenance engineers such as auto-learn of loops walk test and double address detection.CPD approved by LPCB BRE VdSKit Includes1 x 020-538 - Basic Equipment kit 2-8 Loops1 x 020-579 - 7A PSU 4.5A or 7A User selectable1 x 020-543- Dual transmittion path board kit1 x 020-588 - Dual loop board kit1 x 020-474-009 - Extended deep back-box kit Space for up to 38Ah batteries. H620mm W500mm D220mm.1 x 020-480-009 - Main cover kit1 x 020-485-009 - Extension cover blanking kit1 x 020-481-009 - Extension cover kit

GBP 4722.00
1

Notifier ID3000 4 Loop Addressable Control Panel with 4.5A Power Supply and 64 Zone LED Interface 020-730

Notifier ID3000 4 Loop Addressable Control Panel with 4.5A Power Supply and 64 Zone LED Interface 020-730

Notifier ID3000 4 Loop Addressable Control Panel with 4.5A Power Supply and 64 Zone LED Interface 020-730The Notifier ID3000 family of fire alarm control panels deliver the power and flexibility to meet the even the most demanding of requirements. From 2 to 8 loops in a single ID3000 panel to over 500 loops on a network an ID3000 system offers unrivalled stability versatility and capacity. When it comes to giving you the earliest possible warning of a potential fire threat the ID3000 supports Notifiers comprehensive range of detectors advanced fire detection sensors and loop devices delivering you the most complete and versatile fire alarm system in the market place.The ID3000 can be programmed to adapt to the different uses of the areas where smoke detectors are installed. A total of 9 different sensitivity levels can be assigned to individual smoke sensors thereby allowing the system designer to closely match the sensors response to the environment in which the device is located. This even allows smoke detection to be turned off leaving heat detection active.Key Features2-8 Analogue Addressable Loops each of up to 198 devices255 Fire zones per panelFully approved peer to peer network of up to 63 panels maintains 3 second call point response time over the networkFlexible timer functions system sensitivity and functionality can be tailored for the time of day or day of weekSophisticated cause and effect programming including support for non-fire signals and over-ride capability for smoke control systems.Convenience features for commissioning and maintenance engineers such as auto-learn of loops walk test and double address detection.CPD approved by LPCB BRE VdSKit Contains1 x 020-538 - Basic Equipment kit 2-8 loops1 x 020-588 - Dual loop board kit1 x 020-579 - PSU 7A power supply 4.5A or 7A user selectable1 x 020-543 - Dual transmission path board kit1 x 020-474-009 - Extended deep back-box kit Space for up to 38Ah batteries. H620mm W500mm D220mm.1 x 020-480-009 - Main cover kit1 x 020-481-009 - Extension cover kit1 x 020-559-001 - Extension chassis kit. LED indications for zones 1-64. Space for internal printer

GBP 4599.50
1

Notifier Honeywell ABT-ISLE Audio RS485 Interface

Notifier Honeywell ABT-ISLE Audio RS485 Interface

Notifier Honeywell ABT-ISLE Audio RS485 InterfaceThe ABT-ISLE allows integration with other interfaces and different devices using RS485 protocol. Its also audio cable splitter from 1 x RJ45 consisting of 4 analogue audio channels coming out from Audio Out on CU to 4 x RJ45 where each of RJ45 includes 1 audio channel for amplifier input. Unit housing is designed for rack rails TH 35. Address of the ABT-ISLE must be unique and can be set by dedicated Addressing POT 16 addresses 0-F. First module in chain must have address 0.DetailsLocal AUDIO IN For easier and faster connection of audio sources you can use 8 pin Phoenix type connector. LOCAL AUDIO IN on 8 pin Phoenix connector is connected directly with LOCAL AUDIO OUT on RJ-45Audio OUT 1-4 4xRJ-45 for connecting audio signal to amplifiersPSM RJ-45 for connecting with the power manager ABT-PSM48

GBP 376.12
1

Notifier BRH-PC-I02 High Performance Detector Base Sounder Strobe NFXI-BSF-WCH

Notifier BRH-PC-I02 High Performance Detector Base Sounder Strobe NFXI-BSF-WCH

Notifier BRH-PC-I02 High Performance Detector Base Sounder Strobe NFXI-BSF-WCHThe Notifier NFXI-BSF-WCH is a high performance addressable base sounder strobe for use on Notifier protocol analogue addressable fire alarm panels.Key FeaturesRed FlashPure White BodyClear Lens cw IsolatorLoop-powered EN54-23 C Category - High Performance Detector Base Sounder StrobeEN54-23 certifiedCoverage volume code C-3-15 High C-3-11 Low C O-1-4 Legacy

GBP 89.04
1

Notifier NFS 8 Zone Conventional Fire Alarm Panel

Notifier NFS 8 Zone Conventional Fire Alarm Panel

Notifier NFS 8 Zone Conventional Fire Alarm PanelDeveloped with efficiency in mind NFS2-8 zone non-addressable fire alarm panels offer both installers and end users a technically advanced range of functions while remaining easy to install program and operate. A full range of non-addressable detectors advanced non-addressable detectors beam detectors manual call points duct mounting applications audible and visible devices are available for use with the panels.NFS2-8 series fire alarm panels are ideally suited for facilities including offices shop units public houses B B clubs small industrial units nursing homes and schools offering a wide range of benefits to installers and end-users.Key FeaturesCPD approved to EN54-24Simple to installRobust fire resistant ABS moulded enclosureBattery space for up to 72 hour stand-by2 4 or 8 zone versions available Advanced FeaturesZones configurable for delay coincidence short-circuit alarm capacitor or resistive end of line.Fire and fault outputs - volt-free relay or monitoredAuxiliary power output for ancillary equipment2 configurable inputs for ancillary equipment e.g. class change alert etc.Space for two option modulesOptional 8-way relay module common or zonal switchingOptional 1.5A 4-way sounder module common or zonal switching

GBP 511.06
1

Notifier NFS 2 Zone Conventional Fire Alarm Panel

Notifier NFS 2 Zone Conventional Fire Alarm Panel

Notifier NFS 2 Zone Conventional Fire Alarm PanelDeveloped with efficiency in mind NFS2-8 zone non-addressable fire alarm panels offer both installers and end users a technically advanced range of functions while remaining easy to install program and operate. A full range of non-addressable detectors advanced non-addressable detectors beam detectors manual call points duct mounting applications audible and visible devices are available for use with the panels.NFS2-8 series fire alarm panels are ideally suited for facilities including offices shop units public houses B B clubs small industrial units nursing homes and schools offering a wide range of benefits to installers and end-users.Product BenefitsCPD approved to EN54-24Simple to installRobust fire resistant ABS moulded enclosureBattery space for up to 72 hour stand-by2 4 or 8 zone versions availableAdvanced FeaturesZones configurable for delay coincidence short-circuit alarm capacitor or resistive end of line.Fire and fault outputs - volt-free relay or monitoredAuxiliary power output for ancillary equipment2 configurable inputs for ancillary equipment e.g. class change alert etc.Space for two option modulesOptional 8-way relay module common or zonal switchingOptional 1.5A 4-way sounder module common or zonal switching

GBP 273.37
1

Notifier Honeywell ABT-DMS Zone Microphone

Notifier Honeywell ABT-DMS Zone Microphone

Notifier Honeywell ABT-DMS Zone MicrophoneABT-DMS can only be used for purposes not related to evacuation alarm. Zone microphone is equipped with intercom function which provides two-way communication between the zone microphones.ABT-DMS has 4 local audio inputs on board and 1 audio output which allows for further system extension. Communication with control units takes place via Ethernet 10100BASE -TX 1 LAN port.DetailsFour non-symmetrical audio inputs 18 stereo jack connectorBuilt-in speakerStereo jack sockets for Headset Audio outImplemented intercom functionExtension up to five 20-button modulesPower supply via POE or locally 48 VDC

GBP 1976.45
1

Notifier Honeywell Black Passive 100V Loudspeaker 582654.B

Notifier Honeywell Black Passive 100V Loudspeaker 582654.B

Notifier Honeywell Black Passive 100V Loudspeaker 582654.BPassive 100 V loudspeaker with weatherproof aluminium housing designed for use with voice alarm systems - certified according to EN 54-24 Type B equipped with two high-quality 4 drivers with treated cones for optimum efficiency in speech and voice alarms.DetailsEN 54-24 certified 100 V loudspeaker for use with voice alarm systemsblack similar to RAL 9005 powder-coatedsuitable for both indoor and outdoor useexceptionally even sound dispersionSIDE LOBE FREEequipped with high performance speakersexcellent speech intelligibility and sound qualityweatherproof without requiring additional protection protection class IP54 in accordance with IEC 529 EN 60529ball impact resistant front grille made from galvanised sheet steel

GBP 2853.19
1

Notifier Honeywell Contact Interface Module CIM 583341.21

Notifier Honeywell Contact Interface Module CIM 583341.21

Notifier Honeywell Contact Interface Module CIM 583341.21The CIM is used as an interface of VARIODYN D1 system for the connection of 8 control contacts. The 8 control contacts can be configured as either an input or an output. Four of the eight contacts can be programmed in the input function with monitoring of connection line. A 3 m long Cat 5 cable is included to connect from CIM to the TWI input of DOM.Key FeaturesEN 54-16 certifiedContacts as inputs or outputs freely programmable 4 of which can be monitoredCAT5 cabling to DOMMounting by mounting to the DIN-track possibleConnection of different trades possible via CIM

GBP 850.14
1

Notifier Honeywell 582652.W White Passive 100V Loudspeaker

Notifier Honeywell 582652.W White Passive 100V Loudspeaker

Notifier Honeywell 582652.W White Passive 100V LoudspeakerPassive 100 V loudspeaker with weatherproof aluminium housing designed for use with voice alarm systems - certified according to EN 54-24 Type B equipped with two high-quality 4 drivers with treated cones for optimum efficiency in speech and voice alarms.DetailsEN 54-24 certified 100 V loudspeaker for use with voice alarm systemsWhite similar to RAL 9016 powder-coatedSuitable for both indoor and outdoor useExceptionally even sound dispersionSIDE LOBE FREE passive realizationEquipped with high performance speakersExcellent speech intelligibility and sound qualityLong reachWeatherproof without requiring additional protection protection class IP54 in accordance with IEC 529 EN 60529Ball impact resistant front grille made from galvanised sheet steel

GBP 2415.96
1

Notifier Honeywell ABT-EOL End of Line Supervision Module

Notifier Honeywell ABT-EOL End of Line Supervision Module

Notifier Honeywell ABT-EOL End of Line Supervision ModuleABT-EOL monitors the integrity of a loudspeaker line and all its branches. Supervision of branched lines requires EOL module for each branch. ABT-EOL provides a filtered load exclusively at the pilot tone frequency and increases reliability of loudspeaker surveillance method based on impedance measurement. Module connects in parallel to the last loudspeaker on a line. It has a 4 different modes which has to be selected according to the results calculated by the EOL calculator.DetailsEN 54-16 certifiedFour power settings ABCDFits on built-in mounts on selected ambient system loudspeakersPowering of the module from the amplifierLoudspeaker line monitoring without additional cablingOpen-circuit short and ground leakage detection

GBP 1057.26
1

Notifier Honeywell Steerable Line Array Speaker DLI-230 ANA Black 582671.B

Notifier Honeywell Steerable Line Array Speaker DLI-230 ANA Black 582671.B

Notifier Honeywell Steerable Line Array Speaker DLI-230 ANA Black 582671.BThe DLI-230 ANA HB is an active electronically steerable line source speaker in black. Its integrated digital 8-channel DSP amplifier is perfectly tuned to the system. It is equipped with 8 x 4 neodymium speakers which are distinguished by their very long excursion.The DLI systems are generally installed in cases where conventional methods cannot get you anywhere because of difficult acoustic conditions and in projects where excellent speech intelligibility and high sound pressure are required.The system allows for programming in real time so it will save a lot of time when setting up. The system can generate two separate dispersion beams which can be operated with variable acoustic beam centres. Furthermore its important features should be emphasized for system integration as per EN 60849 DIN VDE 0828. Linea Focus systems can only be configured with the latest version of Fohhn Audio Soft.

GBP 24677.52
1

Notifier Honeywell Steerable Line Array Speaker DLI-230 ANA White 582671.W

Notifier Honeywell Steerable Line Array Speaker DLI-230 ANA White 582671.W

Notifier Honeywell Steerable Line Array Speaker DLI-230 ANA White 582671.WThe DLI-230 ANA HW is an active electronically steerable line source speaker in white. Its integrated digital 8-channel DSP amplifier is perfectly tuned to the system. It is equipped with 8 x 4 neodymium speakers which are distinguished by their very long excursion.The DLI systems are generally installed in cases where conventional methods cannot get you anywhere because of difficult acoustic conditions and in projects where excellent speech intelligibility and high sound pressure are required. The system allows for programming in real time so it will save a lot of time when setting up.The system can generate two separate dispersion beams which can be operated with variable acoustic beam centres. Furthermore its important features should be emphasized for system integration as per EN 60849 DIN VDE 0828. Linea Focus systems can only be configured with the latest version of Fohhn Audio Soft.

GBP 24095.88
1

Notifier Honeywell ABT-DMS-LCD Zone Microphone with LCD

Notifier Honeywell ABT-DMS-LCD Zone Microphone with LCD

Notifier Honeywell ABT-DMS-LCD Zone Microphone with LCDFor intuitive and easier operation ABT-DMS-LCD has been equipped with a touch-screen display. Navigation in the menu and change of settings is possible by means of both control buttons located next to LCD display and touch-screen display. ABT-DMS-LCD can only be used for purposes not related to evacuation alarm.Zone microphone is equipped with intercom function which provides two-way communication between the zone microphones. ABT-DMS-LCD has 4 local audio inputs on board and 1 audio output which allows for further system extension. Communication with control units takes place via Ethernet 10100BASE -TX 1 LAN port.Details45 LCD touch screen for fast and clear matricing and system managementfour non-symmetrical audio inputs 18 stereo jack connectorbuilt-in speakerstereo jack socets for headset audio outimplemented intercom functionextension up to five 20-button modulespower supply via POE or locally 48 VDC

GBP 2455.62
1

Notifier Honeywell Steerable Line Array Speaker DLI-130 ANA White 582670.W

Notifier Honeywell Steerable Line Array Speaker DLI-130 ANA White 582670.W

Notifier Honeywell Steerable Line Array Speaker DLI-130 ANA White 582670.WThe DLI-130 ANA HW is an active electronically steerable line source speaker in white. Its integrated digital 8-channel DSP amplifier is perfectly tuned to the system. It is equipped with 8 x 4 neodymium speakers which are distinguished by their very long excursion.The DLI systems are generally installed in cases where conventional methods cannot get you anywhere because of difficult acoustic conditions and in projects where excellent speech intelligibility and high sound pressure are required.The system allows for programming in real time so it will save a lot of time when setting up. The system can generate two separate dispersion beams which can be operated with variable acoustic beam centres. Furthermore its important features should be emphasized for system integration as per EN 60849 DIN VDE 0828. Linea Focus systems can only be configured with the latest version of Fohhn Audio Soft.

GBP 14823.86
1

Notifier Honeywell Steerable Line Array Speaker DLI-130 ANA Black 582670.B

Notifier Honeywell Steerable Line Array Speaker DLI-130 ANA Black 582670.B

Notifier Honeywell Steerable Line Array Speaker DLI-130 ANA Black 582670.BThe DLI-130 ANA HB is an active electronically steerable line source speaker in black. Its integrated digital 8-channel DSP amplifier is perfectly tuned to the system. It is equipped with 8 x 4 neodymium speakers which are distinguished by their very long excursion.The DLI systems are generally installed in cases where conventional methods cannot get you anywhere because of difficult acoustic conditions and in projects where excellent speech intelligibility and high sound pressure are required. The system allows for programming in real time so it will save a lot of time when setting up.The system can generate two separate dispersion beams which can be operated with variable acoustic beam centres. Furthermore its important features should be emphasized for system integration as per EN 60849 DIN VDE 0828. Linea Focus systems can only be configured with the latest version of Fohhn Audio Soft.

GBP 14709.49
1