41 results (0,14774 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Kentec MIOU Multi Input Output Unit K559

Kentec MIOU Multi Input Output Unit K559

Kentec MIOU Multi Input Output UnitK559The K559 Multi IO Module offers a convenient and cost effective method of transmitting and receiving signals via an analogue addressable ESP communications loop.Occupying less than 20 of the space required by conventional IO units the MIOU replaces the large and expensive enclosures normally required for this application. With 8 opto-isolated inputs and 8 volt-free relay contacts relay outputs individually selectable as normally open normally closed or switched voltage outputs the MIOU will find a multitude of uses in concentrated IO applications.Key FeaturesMultiple inputs and outputs at one addressOpto isolated inputsVolt free contact or switched voltage outputsConsiderable space and cost saving over discreet IO unitsEasy clip-on din rail mounting methodCompatible with Solo Syncro AS and Syncro control equipmentLow standby supply currentHochiki ESP protocol

GBP 385.93
1

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550m

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550m

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550mINST-SFP-MM-01-K is a fibre optic transceiver for use with multimode fibre optic cable and operates at a nominal wavelength of 850nm.This dongle is locked and pre-configured for use with the Kentec DNX-R-2FFC-K RS485Fibre Dual Fibre Dynamic Network Analyser.INST-SFP-MM-01-K transceivers are hot-pluggable making it quick easy to replace and also swap between alternate fibre optic modes.Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km. The transmitter section uses a Vertical Cavity Surface Emitted Laser and is class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated GaAs detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. INST-SFP-MM-01-K is designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNX-R-2FFC-K analyser module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesPlug-in transceiver for use with DNX-R-2FFC-K analysers provides a multi-mode fibre communication link between transceivers on the networkMax distance between analysers 550mOperating data rates up to 1.25GbpsSingle 3.3V power supply and TTL Logic InterfaceHot-pluggable SFP footprint duplex LC connector interface.Class 1 FDA and IEC60825-1 laser safety compliant.Commercial temperature range -4085oCCompliant with SFF-8472 MSABuilt-in digital diagnostic functions including optical power monitoring

GBP 131.75
1

Kentec K21084M4 Sigma XT 8 Zone 4 Area Extinguishing Control Panel 8 Zone Conventional

Kentec K21084M4 Sigma XT 8 Zone 4 Area Extinguishing Control Panel 8 Zone Conventional

Kentec K21084M4 Sigma XT 8 Zone 4 Area Extinguishing Control Panel 8 Zone ConventionalSigma XT control panels are multi-area extinguishantcontrol panels complying with EN12094-1 EN54-2 and EN54-4. Up to 8 zones ofconventional detection with up to 4 extinguishant areas are available.Standalone extinguishant control units are also availablewith 2 monitored inputs to receive initiating signals from remote firedetection control panels or addressable modules.Each Extinguishant area has a comprehensive set of inputsand outputs and is configurable via a simple programming interface. Allextinguishant areas may have up to 7 serially connected Sigma SI statusindication and control units or ancillary relay boards connected via a simple 4core cable. The versatility of the control panel can be enhanced further by thefitting of up to 7 Sigma CP Ancillary boards K580 or Sigma CP Sounder boards.Key FeaturesApproved to EN12094-1 EN54-2 and EN54-42 4 or 8 detection zones1 to 4 extinguishant areasDual extinguishant outputs for each area configurable as MainReserveFirst and second stage sounder outputs for each areaFirst and second stage volt free changeover contacts for each areaReleased volt free contact per areaFault volt free contact per areaProgrammable extinguishant delaysProgrammable output durationExtract fan controlCountdown indicator shows time until release in secondsMode select and manual release controls per areaMonitored remote manual release inputMonitored remote Hold inputMonitored remote Mode select door interlock inputMonitored remote Released pressure switch inputMonitored remote Low Pressure switch inputMonitored Abort input

GBP 2019.97
1

Kentec A31161M3 Syncro XT 1 Loop Apollo Protocol - 1 Area Extinguishing Control Panel

Kentec A31161M3 Syncro XT 1 Loop Apollo Protocol - 1 Area Extinguishing Control Panel

Kentec A31161M3 Syncro XT 1 Loop Apollo Protocol - 1 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro single loop addressable control module 1 single area extinguishing control moduleSpace to add additional extinguishing moduleDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M3 enclosure 385mm W x 520mm H x 110mm DPlease note The image is for illustrative purposes only.

GBP 1409.28
1

Kentec H31161M3 Syncro XT 1 Loop Hochiki Protocol - 1 Area Extinguishing Control Panel

Kentec H31161M3 Syncro XT 1 Loop Hochiki Protocol - 1 Area Extinguishing Control Panel

Kentec H31161M3 Syncro XT 1 Loop Hochiki Protocol - 1 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro XT 1 loop Hochiki protocol 1 area extinguishing control panelSyncro single loop addressable control module 1 single area extinguishing control moduleSpace to add additional extinguishing moduleDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M3 enclosure 385mm W x 520mm H x 110mm DPlease note The image is for illustrative purposes only.

GBP 1409.28
1

Kentec A31162M3 Syncro XT 1 Loop Apollo Protocol - 2 Area Extinguishing Control Panel

Kentec A31162M3 Syncro XT 1 Loop Apollo Protocol - 2 Area Extinguishing Control Panel

Kentec A31162M3 Syncro XT 1 Loop Apollo Protocol - 2 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 1 loop addressable control module 2 single area extinguishing control modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M3 enclosure 385mm W x 520mm H x 110mm DPlease note The image is for illustrative purposes only.

GBP 1879.03
1

Kentec A31163M4 Syncro XT 1 Loop Apollo Protocol - 3 Area Extinguishing Control Panel

Kentec A31163M4 Syncro XT 1 Loop Apollo Protocol - 3 Area Extinguishing Control Panel

Kentec A31163M4 Syncro XT 1 Loop Apollo Protocol - 3 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 1 loop addressable control module 3 single area extinguishing control moduleSpace to add additional extinguishing modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 5.25 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M4 enclosure 385mm W x 700mm H x 145mm DPlease note The image is for illustrative purposes only.

GBP 2348.80
1

Kentec H32161M3 Syncro XT 2 Loop Hochiki Protocol - 1 Area Extinguishing Control Panel

Kentec H32161M3 Syncro XT 2 Loop Hochiki Protocol - 1 Area Extinguishing Control Panel

Kentec H32161M3 Syncro XT 2 Loop Hochiki Protocol - 1 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 2 loop addressable control module 1 single area extinguishing control moduleSpace to add additional extinguishing moduleDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M3 enclosure 385mm W x 520mm H x 110mm DPlease note The image is for illustrative purposes only.

GBP 1849.68
1

Kentec H32164M4 Syncro XT 2 Loop Hochiki Protocol - 4 Area Extinguishing Control Panel

Kentec H32164M4 Syncro XT 2 Loop Hochiki Protocol - 4 Area Extinguishing Control Panel

Kentec H32164M4 Syncro XT 2 Loop Hochiki Protocol - 4 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro XT 2 loop Hochiki protocol 4 area extinguishing control panelSyncro 2 loop addressable control module 4 single area extinguishing control modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 5.25 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M4 enclosure 385mm W x 700mm H x 145mm DPlease note The image is for illustrative purposes only.

GBP 3258.97
1

Kentec H32163M4 Syncro XT 2 Loop Hochiki Protocol - 3 Area Extinguishing Control Panel

Kentec H32163M4 Syncro XT 2 Loop Hochiki Protocol - 3 Area Extinguishing Control Panel

Kentec H32163M4 Syncro XT 2 Loop Hochiki Protocol - 3 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro XT 2 loop Hochiki protocol 3 area extinguishing control panelSyncro 2 loop addressable control module 3 single area extinguishing control modulesSpace to add additional extinguishing modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 5.25 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M4 enclosure 385mm W x 700mm H x 145mm DPlease note The image is for illustrative purposes only.

GBP 2789.21
1

Kentec A32163M4 Syncro XT 2 Loop Apollo Protocol - 3 Area Extinguishing Control Panel

Kentec A32163M4 Syncro XT 2 Loop Apollo Protocol - 3 Area Extinguishing Control Panel

Kentec A32163M4 Syncro XT 2 Loop Apollo Protocol - 3 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 2 loop addressable control module 3 single area extinguishing control modulesSpace to add additional extinguishing moduleDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 5.25 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M4 enclosure 385mm W x 700mm H x 145mm DPlease note The image is for illustrative purposes only.

GBP 2789.21
1

Kentec A32164M4 Syncro XT 2 Loop Apollo Protocol - 4 Area Extinguishing Control Panel

Kentec A32164M4 Syncro XT 2 Loop Apollo Protocol - 4 Area Extinguishing Control Panel

Kentec A32164M4 Syncro XT 2 Loop Apollo Protocol - 4 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 2 loop addressable control module 4 single area extinguishing control modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 5.25 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M4 enclosure 385mm W x 700mm H x 145mm DPlease note The image is for illustrative purposes only.

GBP 3258.97
1

Kentec H32162M3 Syncro XT 2 Loop Hochiki Protocol - 2 Area Extinguishing Control Panel

Kentec H32162M3 Syncro XT 2 Loop Hochiki Protocol - 2 Area Extinguishing Control Panel

Kentec H32162M3 Syncro XT 2 Loop Hochiki Protocol - 2 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 2 loop addressable control module 2 single area extinguishing control modulesSpace to add additional extinguishing moduleDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M3 enclosure 385mm W x 520mm H x 110mm DPlease note The image is for illustrative purposes only.

GBP 2319.44
1

Kentec A31164M4 Syncro XT 1 Loop Apollo Protocol - 4 Area Extinguishing Control Panel

Kentec A31164M4 Syncro XT 1 Loop Apollo Protocol - 4 Area Extinguishing Control Panel

Kentec A31164M4 Syncro XT 1 Loop Apollo Protocol - 4 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro single loop addressable control module 4 single area extinguishing control modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 5.25 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M4 enclosure 385mm W x 700mm H x 145mm DPlease note The image is for illustrative purposes only.

GBP 2818.57
1

Kentec A32162M3 Syncro XT 2 Loop Apollo Protocol - 2 Area Extinguishing Control Panel

Kentec A32162M3 Syncro XT 2 Loop Apollo Protocol - 2 Area Extinguishing Control Panel

Kentec A32162M3 Syncro XT 2 Loop Apollo Protocol - 2 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 2 loop addressable control module 2 single area extinguishing control modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M3 enclosure 385mm W x 520mm H x 110mm DPlease note The image is for illustrative purposes only.

GBP 2319.44
1

Kentec A32161M3 Syncro XT 2 Loop Apollo Protocol - 1 Area Extinguishing Control Panel

Kentec A32161M3 Syncro XT 2 Loop Apollo Protocol - 1 Area Extinguishing Control Panel

Kentec A32161M3 Syncro XT 2 Loop Apollo Protocol - 1 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 2 loop addressable control module 1 single area extinguishing control moduleSpace to add additional extinguishing moduleDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M3 enclosure 385mm W x 520mm H x 110mm DPlease note The image is for illustrative purposes only.

GBP 1849.68
1

Kentec H31163M4 Syncro XT 1 Loop Hochiki Protocol - 3 Area Extinguishing Control Panel

Kentec H31163M4 Syncro XT 1 Loop Hochiki Protocol - 3 Area Extinguishing Control Panel

Kentec H31163M4 Syncro XT 1 Loop Hochiki Protocol - 3 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro 1 loop addressable control module 3 single area extinguishing control modulesSpace to add additional extinguishing moduleDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M4 enclosure 385mm W x 700mm H x 145mm DPlease note The image is for illustrative purposes only.

GBP 2348.80
1

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310INST-SFP-BiBi-10K-AB-1INST-SFP-BiBi-10K-BA-1 are fibre optic transceivers for use with multi mode fibre optic cable and operate at a nominal wavelength of 850nm.This dongle is locked and preconfigured for use with Kentec DNP-R-2FFC-K Passive Dual Port Optic FibreRS485 Medium Converter.Transceivers are hot-pluggable making them quick easy to replace and also swap between alternate fibre optic modes. Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km.The transmitter section uses a Vertical Cavity Surface Emitted Laser and is Class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated Gas detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. AB-1BA-1 are designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNP-R-2FFC-K converter module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesOperating data rates up to 1.25Gbps10km reach for 9125m Single Mode FibreSingle 3.3V power supply and TTL Logic InterfaceLow power dissipationHot-pluggable SFP footprintBIDI LCUPC type pluggable optical interfaceClass 1 FDA and IEC60825-1 laser safety compliantBuilt in digital diagnostic functions including optical power monitoringRoHS compliant and lead-freeCompliant with SFP MSACompliant with SFF-8472Compliant with IEEE 802.3z

GBP 149.22
1

Kentec H31162M3 Syncro XT 1 Loop Hochiki Protocol - 2 Area Extinguishing Control Panel

Kentec H31162M3 Syncro XT 1 Loop Hochiki Protocol - 2 Area Extinguishing Control Panel

Kentec H31162M3 Syncro XT 1 Loop Hochiki Protocol - 2 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro XT 1 loop Hochiki protocol 2 area extinguishing control panelSyncro 1 loop addressable control module 2 single area extinguishing control modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 3 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M3 enclosure 385mm W x 520mm H x 110mm DPlease note The image is for illustrative purposes only.

GBP 1879.03
1

Kentec H31164M4 Syncro XT 1 Loop Hochiki Protocol - 4 Area Extinguishing Control Panel

Kentec H31164M4 Syncro XT 1 Loop Hochiki Protocol - 4 Area Extinguishing Control Panel

Kentec H31164M4 Syncro XT 1 Loop Hochiki Protocol - 4 Area Extinguishing Control PanelSyncro XT multi area addressable control panel enables extinguishing systems to use all the features and benefits of the more sophisticated detection techniques provided by addressable fire detectors. It also includes other benefits of analogue addressable systems such as control of loop connected sounders beacons and inputoutput modules. With up to 16 zones of addressable detection over one or two loops it ensures every detector can contribute to the extinguishant release.The Syncro XT has up to four extinguishing areas and two releasing outputs per area which can be controlled via simple coincidence detection or via more complex cause and effects configured by the Loop Explorer configuration programme.Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop Explorer configuration programme. All extinguishant areas may have up to seven serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple four-core cable. With the addition of a Syncro network card Syncro XT control panels can be networked to provide scalable extinguishing systems for all sizes of installation.Key FeaturesSyncro XT 1 loop Hochiki protocol 4 area extinguishing control panelSyncro 1 loop addressable control module 4 single area extinguishing control modulesDetection and Extinguishing controls and status indicatorsDual action manual extinguishing release controlAutoManual keyswitchIntegral 5.25 Amp power supply 230V AC inputSpace for 2 x 12V 12Ah SLA batteriesSurface Mount M4 enclosure 385mm W x 700mm H x 145mm DPlease note The image is for illustrative purposes only.

GBP 2818.57
1

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550INST-SFP-BiBi-10K-AB-1INST-SFP-BiBi-10K-BA-1 are fibre optic transceivers for use with multi mode fibre optic cable and operate at a nominal wavelength of 850nm.This dongle is locked and preconfigured for use with Kentec DNP-R-2FFC-K Passive Dual Port Optic FibreRS485 Medium Converter.Transceivers are hot-pluggable making them quick easy to replace and also swap between alternate fibre optic modes. Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km.The transmitter section uses a Vertical Cavity Surface Emitted Laser and is Class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated Gas detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. AB-1BA-1 are designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNP-R-2FFC-K converter module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesOperating data rates up to 1.25Gbps10km reach for 9125m Single Mode FibreSingle 3.3V power supply and TTL Logic InterfaceLow power dissipationHot-pluggable SFP footprintBIDI LCUPC type pluggable optical interfaceClass 1 FDA and IEC60825-1 laser safety compliantBuilt in digital diagnostic functions including optical power monitoringRoHS compliant and lead-freeCompliant with SFP MSACompliant with SFF-8472Compliant with IEEE 802.3z

GBP 149.22
1

Kentec A80161M2 Syncro AS 1 Loop Apollo Protocol Fire Alarm Control Panel With Enable Keyswitch

Kentec A80161M2 Syncro AS 1 Loop Apollo Protocol Fire Alarm Control Panel With Enable Keyswitch

Kentec A80161M2 Syncro AS 1 Loop Apollo Protocol Fire Alarm Control Panel With Enable KeyswitchSyncro AS is an analogue addressable fire control panel available in either one or two detection loops. It combines compact and practical styling with the programming power and connectivity normally associated with much larger systems. With its ease of use and simplicity to install Syncro AS is straightforward to understand for installers commissioning engineers and end users alike. Using the latest microprocessor it provides a flexible control system with high reliability and integrity.Being a multi-protocol panel enabling choice to our customers Syncro AS supports Apollo Argus Vega and Hochiki detection making it ideal for small and medium sites that require advanced fire sensing and evacuation options. It can thought be expanded and networked to become part of much larger systems if the need arises therefore providing a future proof solution for any size of installation. Syncro AS is also available as a Lite version offering a cost-effective solution for smaller standalone installations requiring only one detection loop.Key Features16 zonal LED indicators2 programmable sounder circuits5 programmable inputs3 programmable relays3A power supplyLarge graphic displayReal time clockExpandable from 1 to 2 loopsCertified to EN54-2 EN54-4Up to 512 additional programmable IO viaSyncro IO modulesPowerful network wide cause and effectsSensitivity adjustment and DriftCompensationCan be networked with Syncro control panelsCompatible with Focus and View repeatersSupports Apollo Argus Vega and Hochiki protocolsSame look and feel as Syncro rangeStores 500 last events in event logDial up modem connection availableCompact stylish enclosureInstaller friendly removable equipment chassisDifferent language and character set variants availableFully EN54-2 and EN54-4 compliant

GBP 757.49
1

Kentec V81162M2 AS 2 Loop Argus Vega Protocol Fire Alarm Control Panel With Enable Keyswitch

Kentec V81162M2 AS 2 Loop Argus Vega Protocol Fire Alarm Control Panel With Enable Keyswitch

Kentec V81162M2 AS 2 Loop Argus Vega Protocol Fire Alarm Control Panel With Enable KeyswitchSyncro AS is an analogue addressable fire control panel available in either one or two detection loops. It combines compact and practical styling with the programming power and connectivity normally associated with much larger systems. With its ease of use and simplicity to install Syncro AS is straightforward to understand for installers commissioning engineers and end users alike. Using the latest microprocessor it provides a flexible control system with high reliability and integrity.Being a multi-protocol panel enabling choice to our customers Syncro AS supports Apollo Argus Vega and Hochiki detection making it ideal for small and medium sites that require advanced fire sensing and evacuation options. It can thought be expanded and networked to become part of much larger systems if the need arises therefore providing a future proof solution for any size of installation. Syncro AS is also available as a Lite version offering a cost-effective solution for smaller standalone installations requiring only one detection loop.Key Features16 zonal LED indicators2 programmable sounder circuits5 programmable inputs3 programmable relays3A power supplyLarge graphic displayReal time clockExpandable from 1 to 2 loopsCertified to EN54-2 EN54-4Up to 512 additional programmable IO viaSyncro IO modulesPowerful network wide cause and effectsSensitivity adjustment and DriftCompensationCan be networked with Syncro control panelsCompatible with Focus and View repeatersSupports Apollo Argus Vega and Hochiki protocolsSame look and feel as Syncro rangeStores 500 last events in event logDial up modem connection availableCompact stylish enclosureInstaller friendly removable equipment chassisDifferent language and character set variants availableFully EN54-2 and EN54-4 compliant

GBP 1056.97
1