24 results (0,13648 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 Zone

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 Zone

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 ZoneThe Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesTwo wire serial connectionUp to 7 panels per system230V AC or 24V DC powered versionsFull control over main panelVolt free fire and fault contact outputsPart NumberDescriptionE01020L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 2 Zones SurfaceE01040L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 4 Zones SurfaceE01080L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 8 Zones Surface

GBP 201.43
1

Kentec Sigma CP-R Repeater Panel with 230v PSU amp Standard Enclosure 2 - 8 Zone

Kentec Sigma CP-R Repeater Panel with 230v PSU amp Standard Enclosure 2 - 8 Zone

Kentec Sigma CP-R Repeater Panel with 230v PSU Standard Enclosure 2 - 8 ZoneThe Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesSigma CP-R Two wire serial connectionUp to 7 panels per system230V AC or 24V DC powered versionsFull control over main panelVolt free fire and fault contact outputsAncillary PCB Two wire serial connectionUp to 7 boards per system230V AC or 24V DC powered versionsOpen collector zonal fault outputsVolt free fire coincidence and common fault contact outputsVariants AvailablePart NumberDescriptionK01020M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 2 Zones SurfaceK01040M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 4 Zones SurfaceK01080M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 8 Zones Surface

GBP 295.45
1

Kentec DNP-R-2FFC-K Passive RS485Fibre amp Dual Fibre Dynamic Network Analyser

Kentec DNP-R-2FFC-K Passive RS485Fibre amp Dual Fibre Dynamic Network Analyser

Kentec DNP-R-2FFC-K Passive RS485Fibre Dual Fibre Dynamic Network AnalyserThe DNP-R-2FFC-K is a full fibre or hybrid copperfibre modem developed for use with fire panels in the life safety industry. The equipment is designed to improve the Quality of Service QoS of critical communication networks while operating under the performance criteria required by EN54-13 and BS5839 part 1.DNP-R-2FFC-K is designed to support dual fibre connectivity Fibre in Fibre out using the range of INS Small Form-factor Pluggable fibre optic transceivers. INS transceivers are available to support single-mode multimode and Bi-Directional fibre optic cables with distances of up to 160km.DNP-R-2FFC-K is also designed to support fibre optic to RS485 copper wiring which allows sections of an RS485 network to be converted to fibre optic cables either for enhanced transmission distances or to overcome problems with EMI Electro-Magnetic Interference.Configuring the module for fibre or RS485 fibre configurations is done through a single switch option. Simple LED indications provide detailed information regarding the communication status of each port signal quality transceiver status etc.Key FeaturesSupport Full Fibre or RS485Fibre configurationsOnly one module required per panelSimple LED status indications provide detailed diagnostic infoSupports INS Small Form-factor Pluggable SFP Fibre Optic transceiversRedundant power supply connections for increased reliabilityBaud rate selectable 9600 - 115200 bitssecDIN rail mountingSupport of single and dual port industrial equipment

GBP 1399.07
1

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Sigma CP-R Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs Ancillary PCB Two wire serial connection Up to 7 boards per system 230V AC or 24V DC powered versions Open collector zonal fault outputs Volt free fire coincidence and common fault contact outputs

GBP 304.18
1

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Sigma CP-R Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs Ancillary PCB Two wire serial connection Up to 7 boards per system 230V AC or 24V DC powered versions Open collector zonal fault outputs Volt free fire coincidence and common fault contact outputs

GBP 366.24
1

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs

GBP 254.51
1

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs

GBP 210.79
1

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550m

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550m

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550mINST-SFP-MM-01-K is a fibre optic transceiver for use with multimode fibre optic cable and operates at a nominal wavelength of 850nm.This dongle is locked and pre-configured for use with the Kentec DNX-R-2FFC-K RS485Fibre Dual Fibre Dynamic Network Analyser.INST-SFP-MM-01-K transceivers are hot-pluggable making it quick easy to replace and also swap between alternate fibre optic modes.Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km. The transmitter section uses a Vertical Cavity Surface Emitted Laser and is class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated GaAs detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. INST-SFP-MM-01-K is designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNX-R-2FFC-K analyser module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesPlug-in transceiver for use with DNX-R-2FFC-K analysers provides a multi-mode fibre communication link between transceivers on the networkMax distance between analysers 550mOperating data rates up to 1.25GbpsSingle 3.3V power supply and TTL Logic InterfaceHot-pluggable SFP footprint duplex LC connector interface.Class 1 FDA and IEC60825-1 laser safety compliant.Commercial temperature range -4085oCCompliant with SFF-8472 MSABuilt-in digital diagnostic functions including optical power monitoring

GBP 131.75
1

Kentec INST-SFP-SS-20K-1 SFP Single Mode Fibre Optic Transceiver 20Km

Kentec INST-SFP-SS-20K-1 SFP Single Mode Fibre Optic Transceiver 20Km

Kentec INST-SFP-SS-20K-1 SFP Single Mode Fibre Optic Transceiver 20KmINST-SFP-SS-20K-1 is a fibre optic transceiver for use with single mode fibre optic cable and operates at a nominal wavelength of 1310nm. This dongle is locked and pre-configured for use with the DNX-R-2FFC-K RS485Fibre Dual Fibre Dynamic Network Analyser.INST-SFP-SS-20K-1 transceivers are hot-pluggable making it quick easy to replace and also swap between alternate fibre optic modes. Maximum range is 20Km based upon a 9125m fibre optic cable.The transmitter section uses a multiple quantum well 1310nm laser and is class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated GaAs detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. INST-SFP-SS-20K-1 is designed to be compliant with SFF-8472 MSA. Built in digital diagnostic functions allow monitoring of the transceiver by the DNX-R-2FFC-K analyser module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesPlug-in transceiver for use with DNX-R-2FFC-K analysers provides a single mode fibre communication link between transceivers on the networkMax distance between analysers 20kmOperating data rates up to 1.25Gbps1310nm FP laser transmitter20km reach for 9125m fibre optic cableSingle 3.3V power supply and TTL Logic InterfaceHot-pluggable SFP footprint duplex LC connector interfaceClass 1 FDA and IEC60825-1 laser safety compliantCommercial temperature range 070CCompliant with SFF-8472 MSABuilt-in digital diagnostic functions including optical power monitoring

GBP 131.75
1

Kentec Sigma CP Ancillary PCB K580

Kentec Sigma CP Ancillary PCB K580

Kentec Sigma CP Ancillary PCBK580The Sigma Ancillary Board is compatible with all Sigma CP and CP-R panels which have operating software version V2.0 or above. The board provides common fire common fault coincidence and zonal fire volt free contacts allowing control of sub-systems graphical mimics and plant remotely from the main panel over a two wire data bus.Key FeaturesTwo wire serial connectionUp to 7 boards per system230V AC or 24V DC powered versionsOpen collector zonal fault outputsVolt free fire coincidence and common fault contact outputs

GBP 175.58
1

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550INST-SFP-BiBi-10K-AB-1INST-SFP-BiBi-10K-BA-1 are fibre optic transceivers for use with multi mode fibre optic cable and operate at a nominal wavelength of 850nm.This dongle is locked and preconfigured for use with Kentec DNP-R-2FFC-K Passive Dual Port Optic FibreRS485 Medium Converter.Transceivers are hot-pluggable making them quick easy to replace and also swap between alternate fibre optic modes. Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km.The transmitter section uses a Vertical Cavity Surface Emitted Laser and is Class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated Gas detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. AB-1BA-1 are designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNP-R-2FFC-K converter module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesOperating data rates up to 1.25Gbps10km reach for 9125m Single Mode FibreSingle 3.3V power supply and TTL Logic InterfaceLow power dissipationHot-pluggable SFP footprintBIDI LCUPC type pluggable optical interfaceClass 1 FDA and IEC60825-1 laser safety compliantBuilt in digital diagnostic functions including optical power monitoringRoHS compliant and lead-freeCompliant with SFP MSACompliant with SFF-8472Compliant with IEEE 802.3z

GBP 149.22
1

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310INST-SFP-BiBi-10K-AB-1INST-SFP-BiBi-10K-BA-1 are fibre optic transceivers for use with multi mode fibre optic cable and operate at a nominal wavelength of 850nm.This dongle is locked and preconfigured for use with Kentec DNP-R-2FFC-K Passive Dual Port Optic FibreRS485 Medium Converter.Transceivers are hot-pluggable making them quick easy to replace and also swap between alternate fibre optic modes. Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km.The transmitter section uses a Vertical Cavity Surface Emitted Laser and is Class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated Gas detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. AB-1BA-1 are designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNP-R-2FFC-K converter module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesOperating data rates up to 1.25Gbps10km reach for 9125m Single Mode FibreSingle 3.3V power supply and TTL Logic InterfaceLow power dissipationHot-pluggable SFP footprintBIDI LCUPC type pluggable optical interfaceClass 1 FDA and IEC60825-1 laser safety compliantBuilt in digital diagnostic functions including optical power monitoringRoHS compliant and lead-freeCompliant with SFP MSACompliant with SFF-8472Compliant with IEEE 802.3z

GBP 149.22
1

Kentec DNX-A-2R-K RS485 Dynamic Network Analyser

Kentec DNX-A-2R-K RS485 Dynamic Network Analyser

Kentec DNX-A-2R-K RS485 Dynamic Network AnalyserThe DNX-A-2R-K is an RS485 Dynamic Network Analyser for Ring Topology Networks. This product has been developed to facilitate dynamic network management through the provision of an independent communication layer.The equipment is designed to improve the Quality of Service QoS of critical communication networks while operating under the performance criteria required by EN54-13 and BS5839 part 1.The ports connected to the communications ring are correctly terminated to match the network communications cable impedance to ensure optimum signal quality and amplitude.Signal quality is constantly monitored and the termination impedance is adjusted to compensate for changes in cable impedance due to climatic or physical cable parameter changes.Four InputOutput interfaces are provided for through an independent communications layer. This feature provides a basic redundant network protocol with the mapping configuration managed through the PC graphics IVIEW programming tool.An upgrade license DNX-R-2R-K-UG is available for this module which enables compatibility with IVIEW graphical software for network analysis support.Key FeaturesIndependent reporting with Class A communication redundancy with multiple fault tolerance2.5 kV galvanic isolation on all portsDual and single industrial equipment RS485 connection4 independent IO channels across the redundant network ring for independent protocol redundancyCan operate on Hosted Fibre Ethernet linksSimple LED system status indicationSignal quality and amplitude visual indicationWireless connectivity for remote monitoring using a Bluetooth or WiFi interfaceSupports the generation of system performance reports for Installation commissioningVisual interface provide by IVIEW the graphical user interface with monitoring diagnostics and reporting optionsEnables preventative maintenance management through system degradation monitoringConfiguration and commissioning parameters are stored allowing for system performance tracking over timeBaud rate selectable from 9600-115200 bitssecDIN rail mounting

GBP 1591.74
1

Kentec K04000M2 Sigma CP Sounder PCB - Boxed

Kentec K04000M2 Sigma CP Sounder PCB - Boxed

Kentec K04000M2 Sigma CP Sounder PCB - BoxedThe Sigma K04000M2 is a sounder controller PCB in a steel enclosure which requires a 24v DC power source.The Kentec Sigma CP Sounder Board is compatible with all Sigma CP control panels which have operating software version V3.0 or above.The board provides 8 additional sounder outputs which can be configured as zoned 2-stage or common alarm.All sounder outputs are open and short circuit monitored and any faults on the sounder outputs will be announced at the main fire alarm panel as a sounder fault.A class change input is provided which when activated by a volt free contact closing will switch all sounder outputs on.Mains powered units require only a two core data cable from the main control panel. 24V DC versions require an additional two cores from another 24V DC source which is suitably rated to supply the total sounder current. 230V versions have their own power supply which is rated to supply sounder loads up to 5.25 Amps.Up to 7 Sounder boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. Sounder boards may be connected to the Sigma CP serial bus in addition to Sigma CP ancillary boards and Sigma CP-R repeater panels.The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres. Once Sounder boards have been recognised by the main panel a fault will be announced at the main panel if any become disconnected.Key FeaturesTwo wire serial connectionUp to 7 sounder boards per system24V DC powered - in steel enclosureZoned 2-stage or common alarmAll outputs monitored for open and short circuit faultsIndividual open and short circuit fault indicatorsFully monitored by main control panelClass change input facilityUp to 8 outputs with 1A available from eachCan be connected to serial bus with Ancillary boards and repeatersPower fault input for monitoring remote power supplies

GBP 246.64
1

Kentec K04400M2 Sigma CP Sounder PCB - Boxed

Kentec K04400M2 Sigma CP Sounder PCB - Boxed

Kentec K04400M2 Sigma CP Sounder PCB - BoxedThe Sigma K04400M2 is a sounder controller PCB in a steel enclosure which requires a 230V DC power source.The Kentec Sigma CP Sounder Board is compatible with all Sigma CP control panels which have operating software version V3.0 or above.The board provides 8 additional sounder outputs which can be configured as zoned 2-stage or common alarm.All sounder outputs are open and short circuit monitored and any faults on the sounder outputs will be announced at the main fire alarm panel as a sounder fault.A class change input is provided which when activated by a volt free contact closing will switch all sounder outputs on.Mains powered units require only a two core data cable from the main control panel. 24V DC versions require an additional two cores from another 24V DC source which is suitably rated to supply the total sounder current. 230V versions have their own power supply which is rated to supply sounder loads up to 5.25 Amps.Up to 7 Sounder boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. Sounder boards may be connected to the Sigma CP serial bus in addition to Sigma CP ancillary boards and Sigma CP-R repeater panels.The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres. Once Sounder boards have been recognised by the main panel a fault will be announced at the main panel if any become disconnected.Key FeaturesTwo wire serial connectionUp to 7 sounder boards per system24V DC powered - in steel enclosureZoned 2-stage or common alarmAll outputs monitored for open and short circuit faultsIndividual open and short circuit fault indicatorsFully monitored by main control panelClass change input facilityUp to 8 outputs with 1A available from eachCan be connected to serial bus with Ancillary boards and repeatersPower fault input for monitoring remote power supplies

GBP 522.61
1