165 results (0,19236 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

V450SS Solid Bar Vertical Clamp

V450SS Solid Bar Vertical Clamp

Designed to improve performance in fabrication and engineering clamping applications. The rapid clamping/unclamping made possible by the use of toggle clamps can greatly reduce machine/operator 'down-time' during all stages of production. Clamping Capacity - the forces stated are the maximum loads that can be applied without causing permanent deformation. Due to leverage ratios, the holding capacity will be greatest at the point on the bar nearest to the handle of the clamp and forces stated have been achieved at this point.

GBP 22.99
1

Indexa V450FS Solid Bar Vertical Clamp

Indexa V450FS Solid Bar Vertical Clamp

Designed to improve performance in fabrication and engineering clamping applications. The rapid clamping/unclamping made possible by the use of toggle clamps can greatly reduce machine/operator 'down-time' during all stages of production. Clamping Capacity - the forces stated are the maximum loads that can be applied without causing permanent deformation. Due to leverage ratios, the holding capacity will be greatest at the point on the bar nearest to the handle of the clamp and forces stated have been achieved at this point.

GBP 25.99
1

Indexa V550FA 'U' Bar Adjustable Vertical Clamp

Indexa V550FA 'U' Bar Adjustable Vertical Clamp

U Bar (Adjustable) Type Designed to improve performance in fabrication and engineering clamping applications. The rapid clamping/unclamping made possible by the use of toggle clamps can greatly reduce machine/operator down-time during all stages of production. Clamping Capacity - the forces stated are the maximum loads that can be applied without causing permanent deformation. Due to leverage ratios, the holding capacity will be greatest at the point on the bar nearest to the handle of the clamp and forces stated have been achieved at this point.

GBP 23.99
1

Indexa V450FA 'U' Bar Adjustable Vertical Clamp

Indexa V450FA 'U' Bar Adjustable Vertical Clamp

U Bar (Adjustable) Type Designed to improve performance in fabrication and engineering clamping applications. The rapid clamping/unclamping made possible by the use of toggle clamps can greatly reduce machine/operator down-time during all stages of production. Clamping Capacity - the forces stated are the maximum loads that can be applied without causing permanent deformation. Due to leverage ratios, the holding capacity will be greatest at the point on the bar nearest to the handle of the clamp and forces stated have been achieved at this point.

GBP 24.99
1

1/2" x 1.1/2" x 18" Ground Flat Stock

1/2" x 1.1/2" x 18" Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 22.99
1

Indexa 1/2" x 4" x 18" Ground Flat Stock

Indexa 1/2" x 4" x 18" Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 36.99
1

Indexa 1/8" x 4" x 18" Ground Flat Stock

Indexa 1/8" x 4" x 18" Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 26.99
1

Indexa 6mm x 40mm x 1000mm Ground Flat Stock

Indexa 6mm x 40mm x 1000mm Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 33.99
1

Indexa 5/8" x 5/8" x 18" Ground Flat Stock

Indexa 5/8" x 5/8" x 18" Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 25.99
1

Indexa 16mm x 16mm x 500mm Ground Flat Stock

Indexa 16mm x 16mm x 500mm Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 25.99
1

Indexa 1/4" x 1.1/2" x 18" Ground Flat Stock

Indexa 1/4" x 1.1/2" x 18" Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 20.49
1

Indexa 7/8" x 7/8" x 18" Ground Flat Stock

Indexa 7/8" x 7/8" x 18" Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 35.99
1

Indexa 2mmx50mmx1000mm Ground Flat Stock

Indexa 2mmx50mmx1000mm Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 30.99
1

Indexa 10mm x 25mm x 1000mm Ground Flat Stock

Indexa 10mm x 25mm x 1000mm Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 41.99
1

Indexa 8mm x 25mm x 1000mm Ground Flat Stock

Indexa 8mm x 25mm x 1000mm Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 39.99
1

Indexa 2mm x 30mm x 1000mm Ground Flat Stock

Indexa 2mm x 30mm x 1000mm Ground Flat Stock

Precision ground flat stock supplied as W1.2510 - 01 Tool Steel (100MnCrW1), in a wide range of Metric sizes. Oil hardening gauge plate supplied in annealed condition. It offers good durability, gives excellent wear resistance and holds a good cutting edge. An excellent general purpose grade. Applications include medium run dies, press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. It is also used in applications such as cams, cloth cutters, cold taps, reamers, trimmer dies, tube expander rolls, plastic moulds and woodworking cutters, collets, cutting hobs and strip slitting cutters. Top & bottom surfaces supplied in ground condition. Both ends supplied sawn cut. Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long. Tolerances Thickness: -0/+.002" Width: -0/+.008" Length: -0/+.197" Square Bars: -0/+.002" Material Specification DIN Grade..1.2510 (100MnCrW1) Nearest AISI Standard 01 Hardness 230 HB Surface Roughness max. 3.2m Chemical Composition C Carbon 0.90 - 1.05% Si Silicon .............. 0.15 - 0.35% Mn Manganese 1.00 - 1.20% Cr Chromium . 0.50 - 0.70% V Vanadium 0.05 - 0.15% W Tungsten 0.50 - 0.70% P Phosphorous max. 0.035% S Sulphur max. 0.035% Inch - Preferred Size List Generally available from stock. All sizes listed are 18" long.

GBP 39.99
1