16 results (0,13803 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec CFP Relay Output Card Reset Fault Aux amp Remote Relay Outputs CFP762

C-Tec CFP Relay Output Card Reset Fault Aux amp Remote Relay Outputs CFP762

C-Tec CFP Relay Output Card Reset Fault Aux Remote Relay Outputs CFP762An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Outputs are NOT designed to switch mains voltages.

GBP 46.63
1

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP Relay Output Card as per CFP762 8 outputs per zone relays CFP763An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote and eight output per zone relays.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Output per zone relays will changeover when the corresponding zone is in alarm subject to certain conditions - for full details refer to the instructions downloadable below.Outputs are NOT designed to switch mains voltages.

GBP 67.02
1

C-Tec BF318 Remote LED Indicator Single Gang

C-Tec BF318 Remote LED Indicator Single Gang

C-Tec BF318 Remote LED Indicator Single GangThe BF318 is a high quality remote LED indicator specifically designed for use in fire alarm systems. It incorporates a high intensity wide-angle red LED which is clearly visible from the front of the plate when active. Its primary use is to indicate the activation of hidden or out of-sight fire detectors.Key FeaturesThe front label includes a white write on panel allowing installers to add their own personalised text such as equipment locationsThe unit will fit on 16mm deep flush or surface mount back boxes

GBP 4.00
1

C-Tec NC943B Conventional Single Zone Call Controller

C-Tec NC943B Conventional Single Zone Call Controller

C-Tec NC943B Conventional Single Zone Call ControllerThe NC943B is a single zone call controller cw a 12V 140mA PSU and standby battery. The device is fully compatible with C-TECs entire range of 800 Series Call System components.Key FeaturesCapable of indicating standard constant tone and emergency intermittent tone calls.Includes a volume adjustable sounder and a link-selectable Call AcceptReset button.Power on and Alarm CALLING LEDs.Volt-free relay output for the optional connection of externally powered beacons etc relay activates on active call signal.Standby battery provides up to 24 hours standby and 15 minutes alarm running time.Mounts on a standard UK 25mm double gang flush or surface back box.Also available as part of the NC951 Accessible Toilet Alarm Kit.

GBP 106.38
1

C-Tec QT637 Quantec Enuresis General Purpose Interface Socket

C-Tec QT637 Quantec Enuresis General Purpose Interface Socket

C-Tec QT637 Quantec Enuresis General Purpose Interface SocketAllows bed wet sensors floor pressure mats and bedchair exit sensors to be easily interfaced to a Quantec addressable call system. Includes two 6.35mm remote jack sockets - one for use with a QT635 enuresisbed wet sensor and one that will accept a floor pressure mat QT644 bed exit mat QT633 or chair exit mat QT634.Onboard batteryisolation circuit ensurescompliance with all relevant UK medical directives. Connects to Quantec via the ancillary input on a Quantec master call point or a QT630 dementia care controller. Can be programmed to generate a standard help required or emergency call on activation via a QT423 configurator at the master call point.Key FeaturesIncludes a battery test button and low batteryenuresis active indicators.Supplied on a double gang plate typically located at floor level.Requires a PP3 battery.

GBP 89.00
1

C-Tec CA736 EACIE 1 Way Flat Interface - Double Gang

C-Tec CA736 EACIE 1 Way Flat Interface - Double Gang

C-Tec CA736 EACIE 1 Way Flat Interface - Double GangA loop-powered single way flat interface for use on a C-TEC EVAC-ALERT system which can control one or more evacuation alert devices located inside a flat.Key FeaturesReliable hard-wired technologyCompatible with the self-test facility on C-TECs BF430EA and BF433CEA range of self-testing evacuation alert devicesProvides one open short circuit fault monitored conventional sounder circuit faults are indicated on the CA736 and reported back to the host EVAC-ALERT panelMounts on a standard UK 35mm double gang back box outside the flat for BS 8629 Clause 8 compliance50mA alarm current can power up to 8 evacuation alert sounders most sites require only one alert sounder so this allows additional alert devices to be connected e.g. for the hard of hearingPolling Sounder Circuit Active and Input Fault indicatorsOn-board short circuit loop isolator

GBP 118.24
1

C-Tec EAP28CAEA EAP 2L 8Z 5A CAST C-TEC EACIE Complete With Cabinet

C-Tec EAP28CAEA EAP 2L 8Z 5A CAST C-TEC EACIE Complete With Cabinet

C-Tec EAP28CAEA EAP 2L 8Z 5A CAST C-TEC EACIE Complete With CabinetThe C-Tec EAP28CAEA is designed for areas with low risks of vandalism such as secure or manned reception areas. Can be configured so its evacuation switches are not active until enabled by an external secure switch.DetailsSupplied as a 2 loop 8 zone panel expandable to 48 zones 4 loops using add-on partsEnclosure features a heavy-duty external door with metal hinges 2 secure cam locksCan accommodate up to 38Ah batteriesInternal features include bright LED indicators easy-to-operate evacuation toggle switches and a concealed but intuitive maintenance interfaceFirefighter controls FULLY compliant with the requirements of BS 8629Can be connected to self-testing evacuation alert sounders visual indicators vibrating pillow padsPowered by C-TECs powerful CAST protocol compatible with our ENVISION data management softwareCustomisable slide-in floorzone labelling systemBF321 Evacuation Alert Panel Mains Keyswitch also available allows the Mains supply to the panel to be switched on or off

GBP 5138.66
1

C-Tec C4408D ActiV Diode Base

C-Tec C4408D ActiV Diode Base

C-Tec ActiV Diode Base - C4408DThe C4408D diode base includes a Schottky diode making it ideal for use in systems requiring active head out end of line monitoring a requirement of UK installation standard BS 5839-1. The C4408 non-diode base is available for use in systems that do not have this requirement.Key FeaturesThird-party certified to the relevant parts of EN54 in conjunction with our ActiV detectorsEasy to fit with lots of working spaceCan be ceiling mounted in any orientation due to the true 360 degree viewing angle of the LED indicator strips on all ActiV detectorsIntegrated detectorbase locking mechanism head removal tool and ID tagSimple click and twist designRemote LED terminals for the optional connection to a BF318 Remote indicatorBright tin plated steel terminals can accept fire rated cable of up to 2.5mm in diameterC4408D diode and C4408 non-diode bases availableCompatible with C-TECs entire range of ActiV conventional smoke and heat detectors

GBP 3.16
1

C-Tec CA738 CAST 1 Way Sounder Controller

C-Tec CA738 CAST 1 Way Sounder Controller

C-Tec CA738 CAST 1 Way Sounder ControllerThe CA738 is CAST protocol addressable sounder controllerwith one conventional sounder circuit designed to control a small group ofsounders VADs. It is compatible with CAST ZFPXFP panels and other CASTcompatible fire panels. It mounts on a standard 35mm deep UK double-gang back boxbeing short circuit proof and monitored per BS5839-1.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million-pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesAllows a zonecircuit of conventional fire alarm sounders tobe connected to a CAST protocol fire alarm systemOnboard short circuit loop isolatorConventional sounder circuit is continually monitored foropen and short circuit faults3mA typical alarm current 530uA typical quiescent current 22-40V DCCan provide up to 50mA output current taken from the CASTaddressable loopPolling sounder circuit active and sounder circuit faultindicators

GBP 59.52
1

C-Tec C4408 ActiV Standard Non-Diode Base

C-Tec C4408 ActiV Standard Non-Diode Base

C-Tec ActiV Standard Non-Diode Base - C4408The C4408 is the standard base for the ActiV range of detectors. The C4408D diode base includes a Schottky diode making it ideal for use in systems requiring active head out end of line monitoring a requirement of UK installation standard BS 5839-1. The C4408 non-diode base is available for use in systems that do not have this requirement.Key FeaturesThird-party certified to the relevant parts of EN54 in conjunction with our ActiV detectorsEasy to fit with lots of working spaceCan be ceiling mounted in any orientation due to the true 360 degree viewing angle of the LED indicator strips on all ActiV detectorsIntegrated detectorbase locking mechanism head removal tool and ID tagSimple click and twist designRemote LED terminals for the optional connection to a BF318 Remote indicatorBright tin plated steel terminals can accept fire rated cable of up to 2.5mm in diameterC4408D diode and C4408 non-diode bases availableCompatible with C-TECs entire range of ActiV conventional smoke and heat detectors

GBP 2.98
1

C-Tec EP203 3 Zone Automatic Extinguisher Panel LPCB Certified - EP203

C-Tec EP203 3 Zone Automatic Extinguisher Panel LPCB Certified - EP203

C-Tec EP203 3 Zone Automatic Extinguisher Panel LPCB Certified - EP203The EP203 three zone automatic extinguisher panel has been specifically designed for use in areas housing expensive dangerous or irreplaceable items of equipment. Third-party approved by the LPCB to EN 12094-1 the European standard for Fixed Firefighting Systems - Components for Gas Extinguishing Systems and EN54 parts 2 and 4 the panel epitomises quality durability and reliability.Featuring an intuitive 128 x 64 pixel two-colour graphic display that gives clear and concise feedback to the user installer and commissioning engineer the panel also includes six monitored inputs including hold and abort a time stamped log adjustable flood times and volt-free changeover relays for fire local fire 1st stage active 2nd stage active extractor fan and fault.The panel is supplied in an elegantly styled durable enclosure with all of its electronics - apart from its powerful 3A EN54-4 switch mode PSU - mounted on a detachable metal bridge plate for ease of installation. A wide range of ancillaries are also available including remote status units hold-off and abort buttons line terminators and output expansion relay boards.Key FeaturesThird-party LPCB certificated to EN 12094 part 1 and EN54 parts 2 and 4Functions as a standard three zone fire panel with additional circuitry for controlling the release of fire-suppressing gas into protected areasUnique 128 x 64 pixel graphical display facilitates straightforward system programmingAny combination of activated zones can be programmed to automatically start the panels extinguishant release sequenceIncludes a pull-down front-panel manual release button and two keyswitches for accessing the panels functions and toggling between automanual modeThree conventional sounder circuits two x 1st stage one x 2nd stagePowerful 3A EN54-4 compliant switch mode PSULow quiescent current - less than 40mA on mains failWide range of monitored inputs and auxiliary outputs see schematicAbort and hold inputs allow the panels release sequence to be cancelled or suspended at any timeTime-stamped event logRS485 connections for up to eight flush or surface remote status units with their own LCDs manual release and mode automanual switches. Single gang economy status units without an LCD are also available.Extensive range of commissioning and engineering functionsOptional relay expansion boards and single gang abort and hold buttonsIdeal for use in computer rooms telecommunication centres archive storage areas chemical plants generator rooms museums etc..System line terminator included with all panels

GBP 399.43
1

C-Tec QT603 Quantec Network Splitter

C-Tec QT603 Quantec Network Splitter

C-Tec QT603 Quantec Network SplitterQuantec utilises a unique data protocol that works down two wires andamaximum of 255 addressable devices can be connected to a Quantec Controller dependent on network topology.Addressable devices require 2 network connections. Slave devices such as slave ceiling pullsandslave overdoor lights connect to Quantec via a master call point master ceiling receiver monitoring point or universal programming device using 2 3 or 4 cores of stranded security cable.Wiring must bemade in a Spine and Limb configuration using one or more QT603 network splitters. This allowsthe use of ordinary unscreened cable which simplifies installation fault-finding and commissioning.Key FeaturesAn essential wiringinstallation aid for C-TECsQuantec Addressable Call System.Helps protect against open and short circuit faults and reduces the risk of volt drop.Includes one input and one output connection for Quantecs Spine wiring typically 1.5-2.5mm TE and sixfused 400mA limb connections for the wiring of individual circuits containing Quantecs fielddevices typically 4 core stranded security cable.At least one QT603 is required perQuantec system the more you use the easier it will beto program and fault-find.Install one QT603 per corridor junction locate at the end of the corridor nearest to the Quantec Controller.Ifthe corridor is longer than 50m install the splitter in the centre of the corridor to reduce wiring runs.Mounts on a standard 25mm UK double gang back box.Power and Fault indicators.Max.60 addressable devices per QT603.

GBP 29.40
1

C-Tec PL1K1 Portable Hearing Loop Kit with Storage Shelf 1.2m2

C-Tec PL1K1 Portable Hearing Loop Kit with Storage Shelf 1.2m2

C-Tec PL1K1 Portable Hearing Loop Kit with Storage Shelf 1.2m2Hearing loop systems allow hearing impaired people to hear more clearly. Most hearing aids have a T or MT switch which allows them to pick up the electromagnetic field generated by a hearing loop system. The hearing aid converts this signal into a sound suited to its users specific hearing requirements.Any person with a hearing aid positioned within or near the loop can hear the loop signal by switching their hearing aid to the correct position allowing them to participate more effectively in general conversation ordering goods or services listening to public performances etc.The PL1K1 is ideal for restricted person to person contact in areas such as banks post offices small meeting rooms reception desks open plan offices and ticket booths. The units portable lightweight design means the system can be moved easily from location to location.Key FeaturesSimple one button operation.Integral high-performance microphone.Excellent sound quality.Five years expected battery life under normal operatingcharging conditions.Auto shut-off facility user selectable for 10 30 or 60 minutes helps preserve battery life.Connection of the plug-top charger overrides the timer function to ensure the unit remains operational at all times.Unit can be used as normal whilst charging.Technical SpecificationType - PortableCoverage - 1.2m2 approx.Dimensions - W 271 x H 200 x D 77mm amplifier only 2.82kgInputs 2 x Mic one built-in mic. and one 3.5mm remote mic. socket for AMT or AMD micsIndicators - Power on input level charging required charging in progress audio warning of imminent shutdownControls - Onoff button adjust auto-shut off timer

GBP 202.64
1

C-Tec BF376 Relay on a Plate 24v 5A Single Gang

C-Tec BF376 Relay on a Plate 24v 5A Single Gang

BF376 Relay on a Plate 24v 5A Single GangThe BF376 is a general purpose double-pole polarised 24V 5A relay designed for use in 24V fire alarm systems. It incorporates a high intensity LED which illuminates red when the relay is active. It may be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets roller shutter doors etc.Please note if connecting to a sounder circuit the relay will return to its normal state when the fire condition is cleared or silenced. Check with the approving authority that the proposed arrangement is acceptable prior to installation. The relay can be mounted on 25mm flush or surface mount back boxes. Mains wiring if used should be provided in accordance with the current edition of the IEE Wiring Regs.16th.Ed.The general requirement for any mains supply to the BF376 is fixed wiring using three core cable not less than 1mm2 fed from an isolating switch fuse spur fused at 5A max. This should be exclusive to the BF376 and its load and be labelled accordingly. As an alternative to a switched fused spur any double pole isolating device with a contact separation of 3mm or greater which is fitted with suitable in-circuit protection devices and meets the appropriate national wiring regulations can be used.Technical InformationActivation current Typically 30mA 24VDCIndicators Red relay activated LEDConnections V -V Supply NC C NO SW1 SW2. Contact rating 24Vdc is 5A resistive 2A inductive Contact rating 240Vac is 5A resistive 2A inductiveProduct dimensions mm 85w x 85h x 27d mm can be mounted onto a standard UK 25mm single gang flush or surface back boxConstruction finish White PVC plate light grey label silver nickel contactsIP Rating IP40Weight 78gOperating temperature -10C to 60CKey FeaturesA general purpose double-pole polarised 24V 5A relay designed for use in 24V fire alarm systemsIncorporates a high intensity LED which illuminates red when the relay is activeCan be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets rollershutter doors etcCan be mounted on 25mm flush or surface mount back boxes

GBP 8.15
1

C-Tec PL1K3 Portable Hearing Loop Kit with Carry Case 1.2m2

C-Tec PL1K3 Portable Hearing Loop Kit with Carry Case 1.2m2

C-Tec PL1K3 Portable Hearing Loop Kit with Carry Case 1.2m2Hearing loop systems allow hearing impaired people to hear more clearly. Most hearing aids have a T or MT switch which allows them to pick up the electromagnetic field generated by a hearing loop system. The hearing aid converts this signal into a sound suited to its users specific hearing requirements.Any person with a hearing aid positioned within or near the loop can hear the loop signal by switching their hearing aid to the correct position allowing them to participate more effectively in general conversation ordering goods or services listening to public performances etc.The PL1K3 is ideal for restricted person to person contact in areas such as banks post offices small meeting rooms reception desks open plan offices and ticket booths. The unit is supplied in arobustplastic storage case.Key FeaturesPortable lightweight design.Simple one button operation.Integral high-performance microphone.Excellent sound quality.Five years expected battery life under normal operatingcharging conditions.Auto shut-off facility user selectable for 10 30 or 60 minutes helps preserve battery life.Connection of the plug-top charger overrides the timer function to ensure the unit remains operational at all times.Unit can be used as normal whilst charging.Note this version of our portable loop amplifier does not include a wall-mounting storage shelf.Technical InformationType - PortableCoverage - 1.2m2 approx.Dimensions - W 271 x H 200 x D 77mm amplifier only 2.82kgInputs 2 x Mic one built-in mic. and one 3.5mm remote mic. socket for AMT or AMD micsIndicators - Power on input level charging required charging in progress audio warning of imminent shutdownControls - Onoff button adjust auto-shut off timer

GBP 345.96
1