13 results (0,13286 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec NC883D Conventional 12V Relay Unit

C-Tec NC883D Conventional 12V Relay Unit

C-Tec NC883D Conventional 12V Relay UnitA general purpose double-pole polarised 12V 5A relay ideal for triggering sirens strobes door releases and other third-party equipmentconnected to an800 Series call system. Can be triggered directly from any of the call systems signal lines provided 12V and -V are supplied to its supply terminals.Key FeaturesTypically used to switch extra low voltagesCan also switch Mains voltages provided the guidelines in the main instructions arefollowedIncorporates a high intensity LED which illuminates red when the relay is activeIncludes a white write on areafor the addition of personalised text such as equipment locations

GBP 42.32
1

C-Tec Z928 Zener Barrier - 1 Channel

C-Tec Z928 Zener Barrier - 1 Channel

C-Tec Z928 Zener Barrier - 1 ChannelThe Zener Barrier prevents the transfer of unacceptably high energy from the safe area into the hazardous area. The zener diodes in the Zener Barrier are connected in the reverse direction. The breakdown voltage of the diodes is not exceeded in normal operation. If this voltage is exceeded due to a fault in the safe area the diodes start to conduct causing the fuse to blow. The Zener Barrier has alternating polarities i. e. interconnected zener diodes are employed and one side is grounded. The Zener Barrier can be used for both alternating voltage signals and direct voltage signals.Key Features1-channelAC versionWorking voltage 26 V at 10 ASeries resistance max. 327 Fuse rating 50 mADIN rail mountable

GBP 233.10
1

C-Tec CA734 CA Mini Input Output Module

C-Tec CA734 CA Mini Input Output Module

C-Tec CA734 CA Mini Input Output Module The C-Tec CA734 is a CA Mini Input Output Module using theC-Tec CAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13Includes a switch monitor signal relay and onboard loopisolator7mA typical alarm current 1mA typical quiescent current 22-40V DCFour plastic tabs for surface or panel mountingIncludes a 1A 30V DC volt-free changeover relay. Can alsoswitch 0.3A 125V ACOffers Switch Ve Ve LED V Ve and changeover relayconnectionsFuture header pin offers expansion opportunities forperipheral IO devices

GBP 38.72
1

C-Tec BF376 Relay on a Plate 24v 5A Single Gang

C-Tec BF376 Relay on a Plate 24v 5A Single Gang

BF376 Relay on a Plate 24v 5A Single GangThe BF376 is a general purpose double-pole polarised 24V 5A relay designed for use in 24V fire alarm systems. It incorporates a high intensity LED which illuminates red when the relay is active. It may be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets roller shutter doors etc.Please note if connecting to a sounder circuit the relay will return to its normal state when the fire condition is cleared or silenced. Check with the approving authority that the proposed arrangement is acceptable prior to installation. The relay can be mounted on 25mm flush or surface mount back boxes. Mains wiring if used should be provided in accordance with the current edition of the IEE Wiring Regs.16th.Ed.The general requirement for any mains supply to the BF376 is fixed wiring using three core cable not less than 1mm2 fed from an isolating switch fuse spur fused at 5A max. This should be exclusive to the BF376 and its load and be labelled accordingly. As an alternative to a switched fused spur any double pole isolating device with a contact separation of 3mm or greater which is fitted with suitable in-circuit protection devices and meets the appropriate national wiring regulations can be used.Technical InformationActivation current Typically 30mA 24VDCIndicators Red relay activated LEDConnections V -V Supply NC C NO SW1 SW2. Contact rating 24Vdc is 5A resistive 2A inductive Contact rating 240Vac is 5A resistive 2A inductiveProduct dimensions mm 85w x 85h x 27d mm can be mounted onto a standard UK 25mm single gang flush or surface back boxConstruction finish White PVC plate light grey label silver nickel contactsIP Rating IP40Weight 78gOperating temperature -10C to 60CKey FeaturesA general purpose double-pole polarised 24V 5A relay designed for use in 24V fire alarm systemsIncorporates a high intensity LED which illuminates red when the relay is activeCan be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets rollershutter doors etcCan be mounted on 25mm flush or surface mount back boxes

GBP 8.15
1

C-Tec CA731 CA Mains Switching Input Output Module

C-Tec CA731 CA Mains Switching Input Output Module

C-Tec CA731 CA Mains Switching Input Output Module The C-Tec CA731 is a mains switching input output interfacemodule using the C-Tec CAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13A mains-switching version of our CA730 input output moduleCapable of switching 5A 230 V AC or 5A 30V DCIncorporates the functions of a switch monitor zone monitorand output unitUp to 20 conventional detectors and 10 MCPsAny normally open switch with an EOL resistor fittedA simple normally open or closed switch non-faultmonitoredOnboard short-circuit loop isolator6mA typical alarm current 1.7mA typical quiescent current 22-40V DCIndicators for Loop polling input faults and relay statusIncludes volt free changeover contacts that can be used totrigger rollershutter doors gas shut-off valves smoke vents etcMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 60.32
1

C-Tec APXM XLR 3 Pin Microphone Plate

C-Tec APXM XLR 3 Pin Microphone Plate

C-Tec APXM XLR 3 Pin Microphone PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced microphones with standard 3 pin XLR connectors.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.30
1

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts 6.35mm 14 jack feeds from audio equipment such as stage or church mixing desks etc.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57
1

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-Tecs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts unbalanced electret microphones with 3.5mm mono jack plugs.Part of C-Tecs patented Outreach Plate audio input extension system.Compatible with C-Tecs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.59
1

C-Tec APL Line Level Audio Plate

C-Tec APL Line Level Audio Plate

C-Tec APL Line Level Audio PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.62
1

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm The Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced electret microphones with 6.35mm 14 jack plugs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57
1

C-Tec APXL XLR 3 Pin Line Level Plate

C-Tec APXL XLR 3 Pin Line Level Plate

C-Tec APXL XLR 3 Pin Line Level PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.64
1

C-Tec APM Omni-Directional Plated Microphone

C-Tec APM Omni-Directional Plated Microphone

C-Tec APM Omni-Directional Plated MicrophoneThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesA self-contained omni-directional plated electret microphone complete with onboard mic to line level converter.Part of C-TECs patented Outreach Plate audio input extension system.Provides up to25m2 ambient coverage or 2.5m2 direct speechcoveragewhen located at a ceiling height of 2.5 to 3m.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 53.39
1

C-Tec APXMM Mini-Mixer Plate

C-Tec APXMM Mini-Mixer Plate

C-Tec APXMM Mini-Mixer PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesCombines the functions of anAPXM microphone Outreach plate and an APL dual phono Outreachplate in one double gang device.Accepts balanced or unbalanced microphones with standard 3 pin XLR connectors AND dual phono line level inputs.Gives a more attractive appearance than separate side-by-side single gang Outreach Plates.Counts as one of the total of ten plates permitted aspart of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK doublegang back box.

GBP 96.35
1