8 results (0,13528 seconds)

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Baldwin Boxall 100W Volume Controls with Override Relay BVC100

Baldwin Boxall 6W Volume Controls with Override Relay BVC6

Baldwin Boxall Vigil 3 Audio Output Module BV3AOM8

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125D

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225

Baldwin Boxall Line Vox Unit BT10

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050Q

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050Q

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050QThe Vigil2 BV050Q contains four independent 50 Watt Class D Power amplifiers each with one 500 mV balanced input and a 50 Watt 100V Line output. The front panel status indicators show Supply Healthy Overload Over Temperature and Output Level 10 and 100 max output level for each amplifier. The Active Indicator illuminates when the amplifier is not in Sleep Mode. CLASS D amplifiers are 80 efficient therefore reducing unwanted heat dissipation and power input requirements. Rated output power is obtainable using a 22V battery supply.The BV050Q has a Sleep mode automatically reducing the standby current requirement to typically 50mA per amplifier when operating on batteries. Channel gain may be individually set using the potentiometers on the board behind the front panel. The audio inputs to the amplifiers are presented on separate RJ45 connectors each connector providing the balanced audio input and a ground connection. The outputs are presented on 6-way plugscrew termination connectors providing 50V or 100V output. The 24V DC input is presented on a 2-way crimp connected plug and socket. The power output stage of the amplifier is protected against overload conditions i.e. short circuits or abnormal loads etc. Should the amplifier be subjected to an abnormal load the input to the power amplifier is attenuated to a safe level.The amplifiers output voltage is also sensed and should it exceed 100V the input signal will be attenuated ensuring safe operation without creating unnecessary distortion. Over temperature protection is provided using a sensor attached to the output stage heat sink. Should the temperature exceed 90 Degrees Celsius the input signal to will be attenuated to a safe level and the Overtemp LED will be illuminated. If the system is under surveillance it will cause the surveillance detector to indicate a fault condition due to the gain reduction. Up to three BV050Q Amplifier modules may be mounted in one BVMF equipment frame or more normally two amplifier modules and one switched mode power supply charger module.

GBP 1973.16
1

Baldwin Boxall BVECASE5 Eclipse5 comes with BVMBC amp BV3AOM8 amp BVECASE5AT amp Fan Tray

Baldwin Boxall BVECASE5 Eclipse5 comes with BVMBC amp BV3AOM8 amp BVECASE5AT amp Fan Tray

Baldwin Boxall BVECASE5 Eclipse5 comes with BVMBC BV3AOM8 BVECASE5AT Fan TrayThe VIGIL Eclipse5 is a powerful standalone voice evacuation public address system. A complete fully monitored system which takes less floor space and is ideal for fitting into building risers or places where space is restricted. Modular and fully networkable the VIGIL Eclipse5 provides the solution for any site.The unit houses the required number of input and output modules one BVMBC battery charger Network Interface modules if required suitable batteries and a choice of up to four amplifier mainframes.Key FeaturesA fully integrated voice evacuation system the Eclipse5 takes up minimal floor space and is secured by bolting to a wall or suitable solid uprightEach Eclipse5 is capable of up to 16 zonesConnect up to eight inputs to each Eclipse5Due to its upright design the Eclipse5 is ideal for fitting within the risers of towers and other similar style buildings or small spacesThe system will continue to function in the event of a mains power failure 24 hours quiescent and 30 minutes full use. For some systems a bolt on battery enclosure is required to house additional batteriesModular system with a choice of amplification using the VIGIL3 Ethernet routeing backbone and VIGIL3 transformerless amplifiersMessage synchronisation - even on decentralised systems - with the ability to store up to 254 monitored messagesFully monitored via selectable surveillance using either AC or DC line monitoring methods.The Eclipse5 accepts VIGIL3 two or four way input modulesElectronically balanced 0dBM with up to 24 band parametric equalisation and audio delay of up to one secondOptions include ambient noise sensing facility using noise sensing microphones and an all call fire microphone which can be fitted on the front panelNetworking is via copper multi-mode fibre single mode fibre or any combination of these with 64 simultaneous audio channels.It is possible to network up to 100 Eclipse5 units together offering a total system size of 400 inputs and 800 outputsEclipse5 supports our paging microphone fire microphones and touchscreen control optionsDimensions mm 1125 H x 500 W x 200 D

GBP 4524.20
1