3 results (0,12273 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Baldwin Boxall Omnicare Repeater Unit BVOCRIF

Baldwin Boxall Omnicare Repeater Unit BVOCRIF

Baldwin Boxall Omnicare Repeater Unit BVOCRIFThe EVC repeater unit - BVOCRIF - enables our DTAKIT disabled toilet alarm products to be added to an Omnicare system. The BVOCRIF also acts as a line booster to enable longer cable lengths between outstations andor control panels.Key FeaturesUse the BVOCRIF as an interface for the DTAKIT three part toilet alarm system.Up to two DTAKITs can be fitted to each BVOCRIF repeater will show as one point on the control panel.As an alternative one DTAKIT and an additional pull cord can be fitted to a BVOCRIF. Useful for rooms with two points of call e.g. a toilet cubicle with a shower area.Replaces the BVFREPEM repeater unit formerly used to connect the BVOCDTA products to an Omnicare system.The DTAKIT is suitable for installation on any Omnicare system via the BVOCRIF repeater. The only exception to this is if a system already has the BVOCDTA kits and BVFREPEM repeater modules connected.The BVOCRIF can act as a booster unit to enable cable runs exceeding 200 metres between remote units outstations andor control panels.Repeater units are not seen as an address on the control panel unless connected to a disabled toilet alarm.An internal termination board includes loop through connector for testing site wiring.Self-powered from the ring circuit.Surface mountable.Zintec finish.

GBP 205.93
1

Baldwin Boxall BVECASE5 Eclipse5 comes with BVMBC amp BV3AOM8 amp BVECASE5AT amp Fan Tray

Baldwin Boxall BVECASE5 Eclipse5 comes with BVMBC amp BV3AOM8 amp BVECASE5AT amp Fan Tray

Baldwin Boxall BVECASE5 Eclipse5 comes with BVMBC BV3AOM8 BVECASE5AT Fan TrayThe VIGIL Eclipse5 is a powerful standalone voice evacuation public address system. A complete fully monitored system which takes less floor space and is ideal for fitting into building risers or places where space is restricted. Modular and fully networkable the VIGIL Eclipse5 provides the solution for any site.The unit houses the required number of input and output modules one BVMBC battery charger Network Interface modules if required suitable batteries and a choice of up to four amplifier mainframes.Key FeaturesA fully integrated voice evacuation system the Eclipse5 takes up minimal floor space and is secured by bolting to a wall or suitable solid uprightEach Eclipse5 is capable of up to 16 zonesConnect up to eight inputs to each Eclipse5Due to its upright design the Eclipse5 is ideal for fitting within the risers of towers and other similar style buildings or small spacesThe system will continue to function in the event of a mains power failure 24 hours quiescent and 30 minutes full use. For some systems a bolt on battery enclosure is required to house additional batteriesModular system with a choice of amplification using the VIGIL3 Ethernet routeing backbone and VIGIL3 transformerless amplifiersMessage synchronisation - even on decentralised systems - with the ability to store up to 254 monitored messagesFully monitored via selectable surveillance using either AC or DC line monitoring methods.The Eclipse5 accepts VIGIL3 two or four way input modulesElectronically balanced 0dBM with up to 24 band parametric equalisation and audio delay of up to one secondOptions include ambient noise sensing facility using noise sensing microphones and an all call fire microphone which can be fitted on the front panelNetworking is via copper multi-mode fibre single mode fibre or any combination of these with 64 simultaneous audio channels.It is possible to network up to 100 Eclipse5 units together offering a total system size of 400 inputs and 800 outputsEclipse5 supports our paging microphone fire microphones and touchscreen control optionsDimensions mm 1125 H x 500 W x 200 D

GBP 4524.20
1