39 results (0,14107 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Baldwin Boxall Impedance Monitor BVLAM

Baldwin Boxall Impedance Monitor BVLAM

Baldwin Boxall Impedance Monitor BVLAMThe BVLAM provides 8 zone 100V line relay switching loudspeaker zone selection from 1 amplifier.It incorporates impedance monitoring on all 8 loudspeaker lines when the zone is not selected. If the load increases impedance decreases the appropriate fault LED illuminates steady and if the load decreases impedance increases the fault LED will flash.The impedance changes for a fault to be detected is selected to either 20 or 40 using the mode DIL switch 8. If the impedance falls to approximately 50 of its original value the line is considered to be short circuit and will not be selected to the amplifier.All 8 zone select inputs will access when it is between 2 to 6.5V. An open circuit access input above 15V will be indicated by the appropriate fault LED flashing and a short circuit access input below 2V by the fault LED illuminating steady.Under all fault conditions the OK LED will extinguish and the common fault relay volt-free contacts to change state.Key FeaturesRack-mountable unit 1U high. Two units can be mounted across one rack shelf.Provides eight loudspeaker zone selection from one amplifier.On receipt of a signal from an input ie zone selecting microphone the BVLAM triggers the amplifier to output to the selected zone.An internal relay enables zone switching.The BVLAM provides constant impedance monitoring on each of the eight loudspeaker circuits when not selected.LEDs are used to indicate a drop or increase in impedance - set at either 20 or 40 by DIL switches.Note due to detection accuracy BVLAM is only suitable for BS5839-8 voice alarm systems with less than five speakers per circuit.Access faults on any of the zones from the microphone are indicated by LEDs on the BVLAM.Additional LED indicators are provided to show system healthy and supply healthy.The Baldwin Boxall Impedance Monitor BVLAM provides a combination of zones relay switches from one amplifier. It changes if a fault is detected.

GBP 880.90
1

Baldwin Boxall BVOCODL BVOCDTA Kit SpareOver-Door Light

Baldwin Boxall BVOCODL BVOCDTA Kit SpareOver-Door Light

Baldwin Boxall BVOCODL BVOCDTA Kit SpareOver-Door LightBaldwin Boxall OmniCare CARE2 Disabled Toilet Alarm Assistance Call Kit WhiteThe BS83002009 standard requires that all new disabled WC installations are fitted with an emergency assistance alarm. This Disabled WC Alarm Kit provides a compliant reliable and easy to use disabled persons toilet alarm which contains a controller ceiling pull switch reset point overdoor light.The Controller should be located so that it is easily seen heard by people able to give assistance indicates where help is required. The unit is not suitable for exterior location unless suitably protected against water ingress.The Ceiling Pull Switch must be located so that it can be operated from the WC and from an adjacent floor area. The Ceiling Pull Switch is supplied with two G pulls one should be set a height between 800 1000mm the other set 100mm above the floor level.The Overdoor Light Sounder should be located so that it is easily seen and heard by people able to give assistance and indicates where help is required. Normally above the door outside the WC. The Reset Point should be located inside the WC area so that it is reachable from both a wheelchair and the WC.Kit contains combined power supply and controller with reset button and high visibility LED ceiling mounted G pull cord with LED reset button and LED to reset calls locally overdoor triangular lens lightsounderKey FeaturesIntegral mains powered PSURelay Output optionBS83002009 Acknowledge FeatureIncludes Backup BatteryPowerful LEDs SounderSupply Healthy LEDReset Button EnableDisableSelf-Test FacilityTwin G-Pulls LEDReset Point with Re-Assurance LEDOverdoor Light with SounderWhite Material FinishDisabled Toilet Alarm Assistance Call KitWhiteFully compliant to BS83002009

GBP 65.32
1

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225The BV225 Amplifier module is a 225-Watt Class D Power amplifier with a 500mV Balance Line audio input and 100V Line output. The front panel status indicators show Power Overload and Output Level 10 and 100 output level. The audio input is presented on two separate RJ45 connectors. The output is presented on two 3-way plugcage clamp termination connectors providing 50V or 100V output. The 24V DC input is presented on a two 2-way crimp connected socket.The power output stage of the amplifier is protected against overload conditions i.e. short circuits or abnormal loads. Should an amplifier be subjected to an abnormal load the input to the relevant power amplifier is attenuated to a safe level and the Overload LED will be illuminated. The amplifier output voltages are also sensed and should they exceed 100V the relevant input signal will be attenuated ensuring safe operation without creating unnecessary distortion.Over temperature protection is provided using sensors attached to the output stage heat sink. Should the temperature exceed 90 Degrees Celsius the input signal to the relevant amplifier will be attenuated to a safe level and the Overload LED will be illuminated. If the system is under surveillance it will cause the surveillance detector to indicate a fault condition due to the gain reduction.

GBP 870.91
1

Baldwin Boxall 4-way Disabled Toilet Alarm Control Panel DTA4

Baldwin Boxall 4-way Disabled Toilet Alarm Control Panel DTA4

Baldwin Boxall 4-way Disabled Toilet Alarm Control Panel DTA4Disabled toilet alarms are used as a method for people to call for assistance following a fall or other emergency. They are generally installed in disabled toilet cubicles however they can be used in other places such as bedrooms.Our 4-way controller together with our toilet alarm kits forms a fully compliant to BS8300 easy-to-use disabled toilet alarm solution.The controller has many advantages over similar products on the market today.Key FeaturesIndependent call acceptacknowledge button for each toilet alarm connected.Monitored system with fault LED to indicate if a short or open condition is detected.Independent fault indicators for each line.The panel has a built-in mains supply and is simply installed via a fused spur 3A switched connection to a separate power supply is not required. An LED on the panel confirms that the system is powered and available for use.Up to ten of the panels can be daisy chained for larger systems without the need for any additional power source.A separate relay output enables connection to an external beacon providing the opportunity to add a remote indicator to alert staff in a different area.Full compliance to BS8300 with an acknowledge feature to reassure the caller that help is on the way both audible and visual alarms change at the point of call when acknowledge button is pressed.The system has a programmable alarm re-sound feature. This will operate if a call has been acknowledged at the control unit but is not reset at the point of call within the specified time.Space to independently label each zone for easy identification of the alarm call.Choice of a white or stainless-steel finish as standard.For ease of installation the panel fits into a standard double gang back box not supplied.

GBP 224.08
1

Baldwin Boxall 4 Way Toilet Alarm Control Panel SSteel DTA4S

Baldwin Boxall 4 Way Toilet Alarm Control Panel SSteel DTA4S

Baldwin Boxall 4 Way Toilet Alarm Control Panel SSteel DTA4SDisabled toilet alarms are used as a method for people to call for assistance following a fall or other emergency. They are generally installed in disabled toilet cubicles however they can be used in other places such as bedrooms.Our 4-way controller together with our toilet alarm kits forms a fully compliant to BS8300 easy-to-use disabled toilet alarm solution.The controller has many advantages over similar products on the market today.Key FeaturesIndependent call acceptacknowledge button for each toilet alarm connected.Monitored system with fault LED to indicate if a short or open condition is detected.Independent fault indicators for each line.The panel has a built-in mains supply and is simply installed via a fused spur 3A switched connection to a separate power supply is not required. An LED on the panel confirms that the system is powered and available for use.Up to ten of the panels can be daisy chained for larger systems without the need for any additional power source.A separate relay output enables connection to an external beacon providing the opportunity to add a remote indicator to alert staff in a different area.Full compliance to BS8300 with an acknowledge feature to reassure the caller that help is on the way both audible and visual alarms change at the point of call when acknowledge button is pressed.The system has a programmable alarm re-sound feature. This will operate if a call has been acknowledged at the control unit but is not reset at the point of call within the specified time.Space to independently label each zone for easy identification of the alarm call.Choice of a white or stainless-steel finish as standard.For ease of installation the panel fits into a standard double gang back box not supplied.

GBP 252.20
1

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125D

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125D

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125DThe BV125D Amplifier module contains two independent Class D Power amplifiers each with a single 500mV Balanced Line audio input and 125-Watt 100V Line output. The front panel status indicators show Power Overload and Output Level 10 and 100 output level for both amplifiers.The audio inputs to each amplifier are presented on separate RJ45 connectors. The outputs are presented on two 3-way plugcage clamp termination connectors providing 50V or 100V output. The 24V DC inputs are presented on two 2-way crimp connected sockets. The power output stages of the amplifiers are protected against overload conditions i.e. short circuits or abnormal loads.Should an amplifier be subjected to an abnormal load the input to the relevant power amplifier is attenuated to a safe level and the Overload LED will be illuminated. The amplifier output voltages are also sensed and should they exceed 100V the relevant input signal will be attenuated ensuring safe operation without creating unnecessary distortion.

GBP 1349.92
1

Baldwin Boxall 3-part White Disabled Toilet Alarm Kit DTAKIT

Baldwin Boxall 3-part White Disabled Toilet Alarm Kit DTAKIT

Baldwin Boxall 3-part White Disabled Toilet Alarm Kit DTAKITThe Baldwin Boxall white toilet alarm kit is a fully compliant BS83002009 system for the OmniCare and CARE2 EVC systems. Additional components can be added to the system to provide an assistance call style system.Kit ContainsPull switch - white - ceiling mounted pull switch with two fully compliant G pulls.Reset point - white - reset button with powerful LED and optional sounder.Lightsounder - white - overdoor triangular lens with integral sounder to attract attention.WC sign - self-adhesive vinyl disabled toilet sign.Key FeaturesCall acknowledge feature - both audible and visual - when a call is accepted reassuring the caller that help is on the way.Up to two toilet alarm kits can be connected to one point on the EVC control panel.Toilet alarms are monitored and battery-backed via the EVC system. There is also an automatic self-test facility which ensures that all sounders and LEDs are fully operational.The kit is available with either a white or stainless-steel finish. Alternatively the parts can be purchased separately to enable a combination of finishes to be applied if required.The kit is also available with a stainless-steel finish product code DTASKIT.

GBP 168.74
1

Baldwin Boxall 3-part Stainless Steel Disabled Toilet Alarm Kit DTASKIT

Baldwin Boxall 3-part Stainless Steel Disabled Toilet Alarm Kit DTASKIT

Baldwin Boxall 3-part Stainless Steel Disabled Toilet Alarm Kit DTASKITThe Baldwin Boxall stainless steel finish toilet alarm kit is a fully compliant BS83002009 system for the OmniCare and CARE2 EVC systems. Additional components can be added to the system to provide an assistance call style system.Kit ContainsPull switch - stainless steel finish - ceiling mounted pull switch with two fully compliant G pulls.Reset point - stainless steel finish - reset button with powerful LED and optional sounder.Lightsounder - stainless steel finish - overdoor triangular lens with integral sounder to attract attention.WC sign - self-adhesive vinyl disabled toilet sign.Key FeaturesCall acknowledge feature - both audible and visual - when a call is accepted reassuring the caller that help is on the way.Up to two toilet alarm kits can be connected to one point on the EVC control panel.Toilet alarms are monitored and battery-backed via the EVC system. There is also an automatic self-test facility which ensures that all sounders and LEDs are fully operational.The kit is available with either a white or stainless-steel finish. Alternatively the parts can be purchased separately to enable a combination of finishes to be applied if required.The kit is also available with a white finish product code DTAKIT.Please note this unit is not for use in humid areas.

GBP 282.14
1

Baldwin Boxall Line Vox Unit BT10

Baldwin Boxall Line Vox Unit BT10

Baldwin Boxall Line Vox Unit BT10The BT10 is a universal interface module. Connect the input of the BT10 to either a 100 Volt loudspeaker line or the line level output from a telephone switch.The output at either microphone or line level can be fed into an amplifier. When a signal of a sufficient level is received at the input the Vox circuit will operate and it will be passed via the output into the amplifier.In addition the unit has a switched 0V available on the ACC terminal to access the amplifier. E.G. When using one of our amplifiers take a connecting wire from the ACC terminal to pin 5 on the appropriate input socket.The Vox circuit is designed to ensure that there will not be any unwanted noise appearing at the amplifier input and being relayed through the loudspeakers.A pre-set control allows adjustment of the Vox sensitivity. To set it adjust the control so that it only switches on when a suitable signal level is present.The TEST LED will illuminate when the Vox has operated and the access will be switched ON. The gain pre-set adjusts the gain of the unit and is factory pre-set at x 2 6 dB.It can be used to compensate for different input signal levels. The unit is powered from either mains or 24 VDC.If both are connected in the event of mains failure there will be automatic switch over to the 24VDC and the unit will continue to operate.

GBP 381.02
1

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050Q

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050Q

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050QThe Vigil2 BV050Q contains four independent 50 Watt Class D Power amplifiers each with one 500 mV balanced input and a 50 Watt 100V Line output. The front panel status indicators show Supply Healthy Overload Over Temperature and Output Level 10 and 100 max output level for each amplifier. The Active Indicator illuminates when the amplifier is not in Sleep Mode. CLASS D amplifiers are 80 efficient therefore reducing unwanted heat dissipation and power input requirements. Rated output power is obtainable using a 22V battery supply.The BV050Q has a Sleep mode automatically reducing the standby current requirement to typically 50mA per amplifier when operating on batteries. Channel gain may be individually set using the potentiometers on the board behind the front panel. The audio inputs to the amplifiers are presented on separate RJ45 connectors each connector providing the balanced audio input and a ground connection. The outputs are presented on 6-way plugscrew termination connectors providing 50V or 100V output. The 24V DC input is presented on a 2-way crimp connected plug and socket. The power output stage of the amplifier is protected against overload conditions i.e. short circuits or abnormal loads etc. Should the amplifier be subjected to an abnormal load the input to the power amplifier is attenuated to a safe level.The amplifiers output voltage is also sensed and should it exceed 100V the input signal will be attenuated ensuring safe operation without creating unnecessary distortion. Over temperature protection is provided using a sensor attached to the output stage heat sink. Should the temperature exceed 90 Degrees Celsius the input signal to will be attenuated to a safe level and the Overtemp LED will be illuminated. If the system is under surveillance it will cause the surveillance detector to indicate a fault condition due to the gain reduction. Up to three BV050Q Amplifier modules may be mounted in one BVMF equipment frame or more normally two amplifier modules and one switched mode power supply charger module.

GBP 1973.16
1

Baldwin Boxall Consisting BVOC8MS. ampBY18 BVOC8MS

Baldwin Boxall Consisting BVOC8MS. ampBY18 BVOC8MS

Baldwin Boxall Consisting BVOC8MS. BY18 BVOC8MSOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 1991.30
1

Baldwin Boxall Consisting BVOC80S.BY90 amp BVOBATT2 BVOC80S

Baldwin Boxall Consisting BVOC80S.BY90 amp BVOBATT2 BVOC80S

Baldwin Boxall Consisting BVOC80S.BY90 BVOBATT2 BVOC80SOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 6598.97
1

Baldwin Boxall Consisting BVOC16MS. ampBY24 BVOC16MS

Baldwin Boxall Consisting BVOC16MS. ampBY24 BVOC16MS

Baldwin Boxall Consisting BVOC16MS. BY24 BVOC16MSOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 2110.15
1

Baldwin Boxall Consisting BVOC96S.BY125 amp BVOBATT3 BVOC96S

Baldwin Boxall Consisting BVOC96S.BY125 amp BVOBATT3 BVOC96S

Baldwin Boxall Consisting BVOC96S.BY125 BVOBATT3 BVOC96SOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 6755.02
1

Baldwin Boxall Consisting BVOC32MS. ampBY24 BVOC32MS

Baldwin Boxall Consisting BVOC32MS. ampBY24 BVOC32MS

Baldwin Boxall Consisting BVOC32MS. BY24 BVOC32MSOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 2874.91
1

Baldwin Boxall Consisting BVOC112S.BY125 amp BVOBATT3 BVOC112S

Baldwin Boxall Consisting BVOC112S.BY125 amp BVOBATT3 BVOC112S

Baldwin Boxall Consisting BVOC112S.BY125 BVOBATT3 BVOC112SOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 7426.34
1

Baldwin Boxall Consisting BVOC4MS. ampBY7.2 BVOC4MS

Baldwin Boxall Consisting BVOC4MS. ampBY7.2 BVOC4MS

Baldwin Boxall Consisting BVOC4MS. BY7.2 BVOC4MSOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 1926.89
1

Baldwin Boxall Consisting BVOC64S.BY90 amp BVOBATT2 BVOC64S

Baldwin Boxall Consisting BVOC64S.BY90 amp BVOBATT2 BVOC64S

Baldwin Boxall Consisting BVOC64S.BY90 BVOBATT2 BVOC64SOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 5360.64
1

Baldwin Boxall Consisting BVOC48S.BY60FT amp BVOBATT2 BVOC48S

Baldwin Boxall Consisting BVOC48S.BY60FT amp BVOBATT2 BVOC48S

Baldwin Boxall Consisting BVOC48S.BY60FT BVOBATT2 BVOC48SOmnicare is a loop wired addressable emergency voice communication system that allows disabled refuge fire telephones steward telephones and disabled toilet alarms to be connected to one panel. Omnicare can be easily networked with the ability to add multiple control panels on a system. This enables local zonearea control with gatehousemanagement control on a master panel.The control panel features an output for an external call indicator. This is designed for use in situations where the control panel is mounted in an unmanned area. Using this output a remote indicator can be fitted in a location where it is visibleheard such as in a reception area. The output has a programmable delay feature so that calls answered at the panel are not relayed to the remote lampbuzzer indicator.Panel options include sizes from four-way up to 128-way and are supplied with the relevant batteries for backup should the mains power fail. Four-way up to 128-way versions of the control panel available in either grey or stainless-steel finish. Omnicare has been designed and built to meet BS99992008 BS5839-92011 and BS83002009 for the disabled toilet alarm.Key FeaturesDigital audio full duplex or speech steered remote dependent.One master and multiple slaves can be networked on one system panels are configured on installation.Surface mountable or optional flush mounting with bezel.Dedicated button control for each outstation with status LED indicators.Lockable glazed door.Remote units are connected to the master control panel in a loop configuration using fire rated enhanced four-core cable. OmniCare cabling networking.Fully monitored and battery backed separate box to house batteries supplied with panels larger than 32-way.The system is addressable via the remote units.System BenefitsMultiple masterslave panels can be linked in one system.Full system monitoring.Choice of outstations including disabled toilet alarms addressable via the remote unit.Link to fire detection system prevents hoax disabled refuge calls toilet alarms and fire telephones remain active. Can be completely or partly overridden.Speech steered disabled refuge remotes and full duplex speech fire telephones and emergency telephones.Battery backed for use in the event of mains power failure 24 hours in standby plus three hours use as standard. These times can be increased if required. Please contact our Sales Department for advice.Wired in a loop configuration.

GBP 4916.11
1