198 results (0,16772 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Apollo Soteria Dimension Mounting Box FL5000-200APO

Apollo Soteria Dimension Mounting Box FL5000-200APO

Apollo Soteria Dimension Mounting Box FL5000-200APOThe Soteria Dimension Mounting Box is moulded from white flame-retardant polycarbonate. Positions for either side or top cable entry are marked on the outside of the Mounting Box to ensure correct cable positioning.An arrow has been placed on the rim to assist in correct orientation of the detector Placing the Mounting Box in the correct orientation in the installation aperture it is secured into position by screwing down the self-aligning fixing tabs. The Soteria Dimension Mounting Box is designed to be used with Soteria Dimension Optical Detectors.

GBP 12.47
1

Apollo Discovery Marine Manual Call Point 58100-970MAR

Apollo Discovery Marine Manual Call Point 58100-970MAR

Apollo Discovery Marine Manual Call Point 58100-970MARThe Discovery Marine Manual Call Point MCP is based on the KAC conventional MCP range. It is electronically and mechanically compatible with previous Apollo call points based on KACs World Series product. The address of each call point is set at the commissioning stage by means of a seven-segment DIL switch.If an MCP is activated it interrupts the normal protocol to give a fast response. A single bi-coloured alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel and may be set to flash each time the call point is polled. The red LED is illuminated when the call point has been activated and sent into alarm.On the isolated versions an amberyellow LED indicates a short-circuit on the loop wiring either side of the call point. Call points can be remotely tested from the panel by transmission of a single bit in the communications protocol. Call points respond by providing a value of 64 which corresponds to the alarm value. The panel should recognise this response as a test signal and should not raise a general alarm.Key FeaturesFlashing LED option to indicate polling Discovery systems onlyPlug and Play terminal connections for fast wiringContinuity link for wiring test before commissioningReports an alarm in under 0.2 secondsResettable element

GBP 78.71
1

Apollo XP95 Intelligent Duct Smoke Detector - 53546-022APO

Apollo XP95 Intelligent Duct Smoke Detector - 53546-022APO

Apollo XP95 Intelligent Duct Smoke Detector - 53546-022APOThe Apollo AP53546-022APO Intelligent Duct Smoke Detector provides early detection of smoke in the air moving through heating and ventilation HVAC ducts in commercial and industrial premises. Its purpose is to prevent the re-circulation of smoke from an area on fire to areas unaffected by the fire when used with a XP95 or Discovery detector.How it worksThe duct smoke detector is fitted to the side top or bottom of the ventilation duct and has to tubes which extent into the air duct through holes in the wall. The perforated sampling tube which spans the duct is placed in the airflow upstream of the exhaust tube which causes a pressure differential in the duct detector. Air is sucked up the sampling tube across the detector and exhausted back into the air duct.Key FeaturesOperates in air speeds of 0.5ms to 20msTransparent cover to view detector head LEDIntegral smoke test port

GBP 71.44
1

Apollo Discovery Optical Smoke Detector 58000-600APO

Apollo Discovery Optical Smoke Detector 58000-600APO

Apollo Discovery Optical Smoke Detector 58000-600APOThe Discovery Optical Smoke Detector operates using the light scatter principle and is ideal for applications where slow-burning or smouldering fires pose a potential risk. Discovery is a range of high-specification analogue addressable fire detectors and alarm devices. Discovery detectors offer effective false alarm management by a combination of EN 54 approved operating modes and sophisticated algorithms. Drift compensation further reduces the likelihood of false alarms caused by a build-up of dust in the sensing chamber.OperationThe Discovery Optical Detector has a white moulded polycarbonate case with wind-resistant smoke inlets. The two indicator LEDs are red in alarm. Within the case is a printed circuit board which on one side has the light-proof chamber with integral gauze surrounding the optical measuring system and on the other the signal processing and communications electronics. An infra-red light emitting diode within its collimator is arranged at an obtuse angle to the photo-diode. The photo-diode has an integral daylight-blocking filter.The IR LED emits a burst of collimated light every second. In clear air the photo-diode receives no light directly from the IR LED because of the angular arrangement and the chamber baffles. When smoke enters the chamber it scatters light from the emitter IR LED onto the photo-diode in an amount related to the smoke characteristics and density. The photo-diode signal is processed to provide an analogue value for transmission when the detector is interrogated.Key FeaturesResponds well to slowburning smouldering firesWell-suited to bedrooms and escape routesUnaffected by wind or atmospheric pressureFive response modesRemote test feature

GBP 40.98
1

Apollo Discovery Marine Optical Smoke Detector 58000-600MAR

Apollo Discovery Marine Optical Smoke Detector 58000-600MAR

Apollo Discovery Marine Optical Smoke Detector 58000-600MARThe Discovery Marine Optical Smoke Detector works using the light scatter principle and is ideal for applications where slow-burning or smouldering fires are likely.Operating PrinciplesThe Discovery Marine Optical Smoke Detector has a white moulded polycarbonate case with wind-resistant smoke inlets.The indicator LEDs are colourless when the detector is in quiescent state and red in alarm. Within the case is a printed circuit board which on one side has the light-proof chamber with integral gauze surrounding the optical measuring system and on the other the signal processing and communications electronics.An infra-red light emitting diode within its collimator is arranged at an obtuse angle to the photo-diode. The photo-diode has an integral daylight-blocking filter.The IR LED emits a burst of collimated light every second.In clear air the photo-diode receives no light directly from the IR LED because of the angular arrangement and the chamber baffles. When smoke enters the chamber it scatters light from the emitter IR LED onto the photo-diode in an amount related to the smoke characteristics and density. The photo-diode signal is processed to provide an analogue value for transmission when the detector is interrogated.Maintenance ServiceDetectors should be maintained according to BS 5839-1 or other locally applicable code. Test Equipment can be ordered from us which can test smoke and heat detectors. Detectors should not be cleaned in the field except for careful removal of exterior dirt with a damp cloth.Key FeaturesResponds well to slow-burning smouldering firesSuitable for bedrooms and escape routesUnaffected by wind or atmospheric pressureRemote test featureRejection of transient signals

GBP 59.16
1

Apollo Discovery Marine Standard Mounting Base 45681-210MAR

Apollo Discovery Marine Standard Mounting Base 45681-210MAR

Apollo Discovery Marine Standard Mounting Base 45681-210MARAll detectors in the Discovery Marine range are for use with the Marine Mounting Base. The mounting base is a low insertion force base with stainless steel contacts for the detector terminals. XPERT 7 Cards are supplied with all Discovery bases.OperationUniversal address cards known as XPERT cards are supplied with all bases. Consult the coding guide in the installation instructions to determine which pips are to be removed from the card to give the correct address. Lay the card on a flat surface pips down insert a screwdriver into the slot on the reverse of the pip to be removed and give a firm twist.When the card is coded insert it into the slot in the side of the appropriate base making sure that the card locks itself into place. As a detector is inserted into the base the remaining pips operate the address buttons on the detector and the detector electronics reads the address.Key FeaturesXPERT 7 Card addressingOne-way fitLocking feature to prevent unauthorised removal

GBP 3.84
1

Apollo Orbis TimeSaver Deep Base - ORB-MB-00019-APO

Apollo Orbis TimeSaver Deep Base - ORB-MB-00019-APO

Apollo Orbis TimeSaver Deep Base - ORB-MB-00019-APOThe TimeSaver Deep Base is a mounting base for Orbis products which has an increased depth which allows for cables to be inserted into the side of the product.Brand InformationOrbis is a range of conventional detectors which has been developed and tested to create advantages for fire engineers and installers as well as owners and users of buildings. Orbis is a range with modern styling and a mounting base that saves installation time. It is electrically compatible with Apollo Series 65 and previous ranges of conventional detector.Orbis is a demonstration of Apollos commitment to the market for high quality conventional detectors for use in small to medium size installations. In developing this range Apollo has put ease of installation and reliability in daily operation at the forefront of considerations. The attractive and compact design means that Orbis will blend in well with all architectural styles.Key Features Grouped terminals to make wiring easyTwo fixing centresLED alignment markCable stripping guideDetector locking mechanismEnables surface wiring

GBP 6.04
1

Apollo Marine Intelligent Base Mounted IR3 Flame Detector 55000-029MAR

Apollo Marine Intelligent Base Mounted IR3 Flame Detector 55000-029MAR

Apollo Marine Intelligent Base Mounted IR3 Flame Detector 55000-029MARThe Intelligent Base Mounted IR3 Flame Detector is designed to protect all indoor areas even in dirty or smoky conditions where open flaming fires may be expected. The detector has three IR sensors that respond to different IR wavelengths in order to discriminate between flames and spurious sources of radiation.ApplicationThe triple IR flame detector is also fast reacting but is also tolerant of fumes vapours steam dust and mist while being unaffected by the phenomena listed above. It may however be affected by modulated IR radiation. Triple IR flame detectors are used in waste handling colour printing and paper manufacturing.OperationThe detector is sensitive to low-frequency flickering infra-red radiation emitted by flames during combustion. Since it responds to flickering radiation the detector can operate even if the lens is contaminated by a layer of oil dust water-vapour or ice. The detector is set to respond to low-frequency radiation at 1-15Hz 0.75-2.7ym in order to detect all flickering flames including those invisible to the naked eye e.g. those emitted by hydrogen fires.The detector has three IR sensors that respond to different IR wavelengths in order to discriminate between flames and spurious sources of radiation. False alarms due to factors such as flickering sunlight are avoided by a combination of filters and signal processing techniques.Key FeaturesResponds to stationary flames with no flickerSensitive to low-frequency flickering IR radiation emitted by flames during combustionCompact flame detector which fits into Discovery Marine mounting basesLoop-poweredFalse alarms due to factors such as flickering sunlight are avoided by a combination of filters and signal processing techniques

GBP 1177.80
1

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APO

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APO

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APOThe Series 65 Optical Smoke Detector incorporates a pulsing LED located within the housing of the detector. The external detector moulding is identical to that of the ionisation detector and has an indicator LED which is clear in quiescent state but produces a red light in alarm.OperationThe Series 65 Optical Smoke Detector has a moulded self-extinguishing white polycarbonate case with wind resistant smoke inlets. Nickel-plated stainless-steel wiper contacts connect the detector to the base. Inside the case a printed circuit board has the optical system mounted on one side and the signal processing electronics on the other. The sensing chamber is a black moulding configured as a labyrinth which prevents penetration of ambient light. The labyrinth has a fine gauze insect-resistant cover. The chamber houses an infrared light emitting diode LED and a photo-diode which has an integral visible-light filter as extra protection against ambient light. Every three seconds the LED emits a burst of collimated light modulated at 4kHz. In clear air light from the LED does not fall directly on the diode because the LED is positioned at an obtuse angle to the diode. When smoke enters the chamber a fraction of the collimated light is scattered onto the photo-diode. If the resulting signal from the photo-diode is above a pre-set threshold the LED emits two more bursts of light this time at two-second intervals. If light is scattered onto the photo-diode by both these pulses due to the presence of smoke the detector signals an alarm state by switching the alarm latch on increasing the current drawn from the supply from about 40A to a maximum of 75mA. This fall in the impedance of the detector is recognised by the control panel as an alarm signal. The alarm current also illuminates the detector integral LED. A remote indicator connected between the L1 IN terminal and the R terminal will have a voltage equal to the supply voltage less 1 volt across it and so will illuminate. To ensure correct operation of the detector the control panel must be arranged to supply a maximum of 33 Volts dc and a minimum of 9 Volts dc in normal operation. The supply may fall to 6 Volts dc in alarm conditions if a supply current of at least 10mA is available at this voltage. To ensure effective illumination of the integral LED and any remote indicator the supply to the detector should exceed 12 Volts. To restore the detector to quiescent condition it is necessary to expel any smoke and interrupt the electrical supply to the detector for a minimum of one second.Key FeaturesResponds well to slow-burning smouldering firesWell-suited to bedrooms and escape routesUnaffected by wind or atmospheric pressureFlashing LED and magnet operated test switch option

GBP 19.98
1

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APO

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APO

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APOThe Series 65 Optical Smoke Detector incorporates a pulsing LED located within the housing of the detector. The external detector moulding is identical to that of the ionisation detector and has an indicator LED which is clear in quiescent state but produces a red light in alarm.OperationThe Series 65 Optical Smoke Detector has a moulded self-extinguishing white polycarbonate case with wind resistant smoke inlets. Nickel-plated stainless-steel wiper contacts connect the detector to the base. Inside the case a printed circuit board has the optical system mounted on one side and the signal processing electronics on the other. The sensing chamber is a black moulding configured as a labyrinth which prevents penetration of ambient light.The labyrinth has a fine gauze insect-resistant cover. The chamber houses an infrared light emitting diode LED and a photo-diode which has an integral visible-light filter as extra protection against ambient light. Every three seconds the LED emits a burst of collimated light modulated at 4kHz. In clear air light from the LED does not fall directly on the diode because the LED is positioned at an obtuse angle to the diode. When smoke enters the chamber a fraction of the collimated light is scattered onto the photo-diode.If the resulting signal from the photo-diode is above a pre-set threshold the LED emits two more bursts of light this time at two-second intervals. If light is scattered onto the photo-diode by both these pulses due to the presence of smoke the detector signals an alarm state by switching the alarm latch on increasing the current drawn from the supply from about 40A to a maximum of 75mA. This fall in the impedance of the detector is recognised by the control panel as an alarm signal. The alarm current also illuminates the detector integral LED. A remote indicator connected between the L1 IN terminal and the R terminal will have a voltage equal to the supply voltage less 1 volt across it and so will illuminate.To ensure correct operation of the detector the control panel must be arranged to supply a maximum of 33 Volts dc and a minimum of 9 Volts dc in normal operation.The supply may fall to 6 Volts dc in alarm conditions if a supply current of at least 10mA is available at this voltage. To ensure effective illumination of the integral LED and any remote indicator the supply to the detector should exceed 12 Volts. To restore the detector to quiescent condition it is necessary to expel any smoke and interrupt the electrical supply to the detector for a minimum of one second.Key FeaturesResponds well to slow-burning smouldering firesWell-suited to bedrooms and escape routesUnaffected by wind or atmospheric pressureFlashing LED and magnet operated test switch option

GBP 16.52
1

Apollo Marine DIN-Rail Dual Isolator 55000-770MAR

Apollo Marine DIN-Rail Dual Isolator 55000-770MAR

Apollo Marine DIN-Rail Dual Isolator 55000-770MARThe Marine DIN-Rail Dual Isolator provides in one housing two independent isolators which sense and isolate short-circuits on loops and spurs. This unit needs to be installed in a suitable enclosure Part No. 29600-239240 or equivalent and secured using the end stops.OperationThe isolators are loop-powered and are polarity sensitive. A maximum of twenty detectors may be installed between isolators. When a short-circuit condition exists on either side of the isolator the yellow LED is illuminated.Under normal operating conditions a low impedance is present between the two negative terminals of each isolator channel so that power and signals are passed to the next base in line.If a short-circuit or abnormally low impedance occurs across the loop the fall in voltage is sensed and the isolator isolates the negative supply in the direction of the fault. In this condition the yellow LED of the affected channel will be illuminated. The isolated section of loop is tested using a current pulse every five seconds. When the short-circuit is removed the power will automatically be restored.Key FeaturesLoop-poweredUp to 20 detectors can be installed between isolatorsAllows fully isolated spurs

GBP 78.92
1

Apollo Discovery White Open-Area Voice Sounder Beacon - 58000-040APO

Apollo Discovery White Open-Area Voice Sounder Beacon - 58000-040APO

Apollo Discovery White Open-Area Voice Sounder Beacon - 58000-040APODiscovery Open-Area Voice Sounders comprise a sounder and a sounder visual indicator that have been designed to provide clear instructional messages through the Discovery protocol. They are loop powered wall mounted devices. Discovery is a range of high-specification analogue addressable fire detectors and alarm devices. Discovery detectors offer effective false alarm management by a combination of EN 54 approved operating modes and sophisticated algorithms.The Discovery Open-Area Voice Sounders are used to provide audible and visual warning of a fire condition and are controlled by the fire control panel by means of the Discovery protocol. This particular feature is only available when being controlled by the full Discovery or CoreProtocol with the fire control panel programmed accordingly. Information on available features should be requested from the panel manufacturer.Key FeaturesFour pre-set message pairsCapable of up to 15 tone message pairsLow current and high volumeFully synchronisedSet up and test at point of installation

GBP 158.50
1

Apollo Discovery White Open-Area Voice Sounder - 58000-020APO

Apollo Discovery White Open-Area Voice Sounder - 58000-020APO

Apollo Discovery White Open-Area Voice Sounder - 58000-020APODiscovery Open-Area Voice Sounders comprise a sounder that have been designed to provide clear instructional messages through the Discovery protocol. They are loop powered wall mounted devices. Discovery is a range of high-specification analogue addressable fire detectors and alarm devices.The Discovery Open-Area Voice Sounders are used to provide audible warning of a fire condition and are controlled by the fire control panel by means of the Discovery protocol. This particular feature is only available when being controlled by the full Discovery or CoreProtocol with the fire control panel programmed accordingly.Key FeaturesFour pre-set message pairsCapable of up to 15 tone message pairsLow current and high volumeFully synchronisedSet up and test at point of installation

GBP 129.07
1

Apollo Marine Intelligent Base Mounted UV Flame Detector 55000-027MAR

Apollo Marine Intelligent Base Mounted UV Flame Detector 55000-027MAR

Apollo Marine Intelligent Base Mounted UV Flame Detector 55000-027MARThe Marine Intelligent Base Mounted UV Flame Detector is designed to protect enclosed indoor areas where open fires may be expected. The detector has a fast-acting response to flames up to 25m away and is equipped with a single UV sensor with a narrow spectral response in order to discriminate between flames and most spurious sources of radiation.ApplicationUV flame detectors are used when detection is required to be unaffected by convection currents draughts or wind. These include engine rooms in ships factories affected by draughts or wind and warehouses. They are fast reacting and respond to a flame more than 25m away. The UV flame detector is affected by arc welding electrical sparks lightning nuclear radiation and UV light sources. For applications where these phenomena are present a UV flame detector should not be used.OperationThe detector is sensitive to ultraviolet radiation emitted by flames during combustion. Since it requires only UV radiation the detector responds even to stationary flames with no flicker like cigarette lighters and blue gas flames.The detector is set to respond to ultraviolet radiation 185260nm emitted by almost all flames including those invisible to the naked eye e.g. hydrogen fires. The detector has a single UV sensor with a narrow spectral response in order to discriminate between flames and most spurious sources of radiation and is designed for internal fully enclosed areas. Caution The detector will also detect electrical discharges from lightning or arc welding.Key FeaturesResponds to stationary flames with no flickerSensitive to UV radiation emitted by flames during combustionCompact flame detector which fits into Discovery Marine baseLoop-powered

GBP 982.80
1

Apollo Marine Intelligent Base Mounted UVIR2 Flame Detector 55000-028MAR

Apollo Marine Intelligent Base Mounted UVIR2 Flame Detector 55000-028MAR

Apollo Marine Intelligent Base Mounted UVIR2 Flame Detector 55000-028MARThe Marine Intelligent Base Mounted UV Dual IR Flame Detector is designed to protect open indoor areas where open flaming fires may be expected. The detector has a UV and dual IR sensors responding to different wavelengths in order to discriminate between flames and spurious sources of radiation. They are used in aircraft hangers generator rooms diesel and gas turbines and paint works.OperationThe detector is sensitive to ultraviolet and low-frequency flickering infra-red radiation emitted by flames during combustion. Since it requires both UV and IR radiation the detector can operate in applications where a basic single UV or single IR detector would be inappropriate. The detector is set to respond to ultraviolet 185 - 260nm and low-frequency flickering infra-red 0.75 - 2.7ym radiation at 1 - 15Hz in order to detect all flickering flames including those invisible to the naked eye e.g. those emitted by hydrogen fires.The detector has one UV and two IR sensors responding to different wavelengths in order to discriminate between flames and spurious sources of radiation. False alarms due to electrical discharges from lightning or arc welding and flickering sunlight are minimised by combining the UVIR signals.Key FeaturesResponds to stationary flames with no flickerSensitive to low-frequency flickering IR radiation emitted by flames during combustion.Compact flame detector which fits into Discovery Marine basesLoop-poweredFalse alarms due to factors such as flickering sunlight are avoided by a combination of filters and signal processing techniques

GBP 1177.80
1

Apollo Waterproof Addressable Manual Call Point 58200-951APO

Apollo Waterproof Addressable Manual Call Point 58200-951APO

Apollo Waterproof Addressable Manual Call Point 58200-951APOThe Apollo Waterproof Manual Call Point has a highly visible alarm indicator which can be seen from up to 10 metres away. The manual call point interrupts the polling cycle for a fast response when activated. A combined LED indicator and front reset mechanism allows for a simple reset.OperationThe address of each Manual Call Point is set at the commissioning stage by means of a seven-segment DIL switch. A red alarm LED is provided on the Manual Call Point. This LED is controlled independently of the Manual Call Point by the fire control panel.Once activated the Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs. The isolated version of the Manual Call Point incorporates a short circuit isolator which will ensure its operation in the event of a short circuit fault on the loop. Isolator operation is indicated by a yellow LED.Key FeaturesIP67 ratedEN54-11 approved EN54-17 approved for Isolator versionE-Z fit connectorsFront facing addressing without the need to detach the backboxA unique ergonomically designed key for resetting and front cover removal

GBP 112.84
1

Apollo Intelligent White Manual Call Point - SA5900-903APO

Apollo Intelligent White Manual Call Point - SA5900-903APO

Apollo Intelligent White Manual Call Point - SA5900-903APOThe Intelligent Manual Call Point has been designed for indoor applications and are available in a variety of colours for different applications such as initiating a hazard rather than a fire alarm. The Intelligent Manual Call Point can be used on XP95 Discovery and CoreProtocol systems.A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.OperationThe address of each call point is set at the commissioning stage by means of a DIL switch. A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.Key FeaturesResettable operating elementEasy access front reset mechanismE-Z fit connector system for installationErgonomic reset key170 viewableLED Continuity link for cable insulation testingSuitable for semi flush or surface mounting

GBP 46.91
1

Apollo Intelligent Blue Manual Call Point - SA5900-905APO

Apollo Intelligent Blue Manual Call Point - SA5900-905APO

Apollo Intelligent Blue Manual Call Point - SA5900-905APOThe Intelligent Manual Call Point has been designed for indoor applications and are available in a variety of colours for different applications such as initiating a hazard rather than a fire alarm. The Intelligent Manual Call Point can be used on XP95 Discovery and CoreProtocol systems.A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.OperationThe address of each call point is set at the commissioning stage by means of a DIL switch. A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.Key FeaturesResettable operating elementEasy access front reset mechanismE-Z fit connector system for installationErgonomic reset key170 viewableLED Continuity link for cable insulation testingSuitable for semi flush or surface mounting

GBP 46.91
1

Apollo Intelligent Orange Manual Call Point - SA5900-907APO

Apollo Intelligent Orange Manual Call Point - SA5900-907APO

Apollo Intelligent Orange Manual Call Point - SA5900-907APOThe Intelligent Manual Call Point has been designed for indoor applications and are available in a variety of colours for different applications such as initiating a hazard rather than a fire alarm. The Intelligent Manual Call Point can be used on XP95 Discovery and CoreProtocol systems.A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.OperationThe address of each call point is set at the commissioning stage by means of a DIL switch. A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.Key FeaturesResettable operating elementEasy access front reset mechanismE-Z fit connector system for installationErgonomic reset key170 viewableLED Continuity link for cable insulation testingSuitable for semi flush or surface mounting

GBP 47.57
1

Apollo Intelligent Yellow Manual Call Point - SA5900-904APO

Apollo Intelligent Yellow Manual Call Point - SA5900-904APO

Apollo Intelligent Yellow Manual Call Point - SA5900-904APOThe Intelligent Manual Call Point has been designed for indoor applications and are available in a variety of colours for different applications such as initiating a hazard rather than a fire alarm. The Intelligent Manual Call Point can be used on XP95 Discovery and CoreProtocol systems.A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.OperationThe address of each call point is set at the commissioning stage by means of a DIL switch. A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.Key FeaturesResettable operating elementEasy access front reset mechanismE-Z fit connector system for installationErgonomic reset key170 viewableLED Continuity link for cable insulation testingSuitable for semi flush or surface mounting

GBP 46.91
1

Apollo Intelligent Green Manual Call Point - SA5900-906APO

Apollo Intelligent Green Manual Call Point - SA5900-906APO

Apollo Intelligent Green Manual Call Point - SA5900-906APOThe Intelligent Manual Call Point has been designed for indoor applications and are available in a variety of colours for different applications such as initiating a hazard rather than a fire alarm. The Intelligent Manual Call Point can be used on XP95 Discovery and CoreProtocol systems.A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.OperationThe address of each call point is set at the commissioning stage by means of a DIL switch. A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.Key FeaturesResettable operating elementEasy access front reset mechanismE-Z fit connector system for installationErgonomic reset key170 viewableLED Continuity link for cable insulation testingSuitable for semi flush or surface mounting

GBP 46.91
1

Apollo SA5900-928MAR Intelligent Marine Manual Call Point

Apollo SA5900-928MAR Intelligent Marine Manual Call Point

Apollo SA5900-928MAR Intelligent Marine Manual Call PointThe Intelligent Marine Manual Call Point MCP has been designed to operate on a loop of intelligent fire detection devices. An alarm is initiated by pressing the resettable element. The MCP signals to the Fire Control Panel using an interrupt feature within the Apollo Digital Communication Protocol. An alarm status is indicated through the rotation of the resettable element displaying yellow and black indication bars and a solid red LED. The MCP can be easily reset from the front using the supplied reset key. The Intelligent Marine MCP is intended for indoor marine and offshore applications and has a built-in short circuit isolator.OperationThe address of each call point is set at the commissioning stage by means of a DIL switch. A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Marine Manual Call Point SIL Approved can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.The Intelligent Marine Manual Call Point incorporates a short circuit isolator which will ensure its operation in the event of a short circuit fault on the loop. Isolator operation is indicated by a solid yellow LED.Key FeaturesResettable element for testingEasy access front reset mechanismA unique ergonomically designedKey for resetting and front cover removal

GBP 53.21
1

Apollo Conventional UV Dual IR Flame Detector 55000-064APO

Apollo Conventional UV Dual IR Flame Detector 55000-064APO

Apollo Conventional UV Dual IR Flame Detector 55000-064APOThe combination of UV and IR2 detection plus signal processing allows the sensor to be used without risk of false alarms in difficult situations characterised by factors such as flickering blackbody by radiation or arc welding. Key FeaturesSelectable output options Conventional two-wire 4-20mA Latching or Non-latching Relay Contacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP65 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55COperating temperature -10C to 55C

GBP 2152.80
1

Apollo Discovery Marine Sounder Visual Indicator Base - 45681-394MAR

Apollo Discovery Marine Sounder Visual Indicator Base - 45681-394MAR

Apollo Discovery Marine Sounder Visual Indicator Base - 45681-394MARThe Discovery Marine sounder visual indicator base offers a choice of 15 evacuation tones including the standard Apollo evacuation tone. One of these tones is selected during commissioning in order to suit local regulations or customs.The tones include those required by Dutch Swedish German Australian New Zealand and North American standards as well as the UK. Whichever evacuation tone is selected there is a secondary tone which may be used for alerting or warning of a possible evacuation.ApplicationThe Discovery Marine sounder visual indicator base is used to provide audible and visual warning of fire and is controlled by the fire control panel by means of the Discovery protocol. The particular features of this base are available only when it is being controlled by the full Discovery protocol with the panel programmed accordingly.Information on features should be requested from the panel manufacturer. The Discovery Marine sounder visual indicator base can be used with a detector fitted or with a cap for operation as a stand-alone alarm device.Key FeaturesIt is possible to set individual control of the sounder and visual indicatorVolume and tone settings can be selected from the control panelElectronic bell toneIMO 1A tone included

GBP 103.58
1

Apollo 58100-910APO Discovery Manual Call Point Red

Apollo 58100-910APO Discovery Manual Call Point Red

Apollo 58100-910APO Discovery Manual Call Point RedA seven-segment DIL switch enables addressing of each call point at commissioning stage. When operated the manual call point interrupts the polling cycle for a fast response. Bi-coloured LEDs indicate isolate and normal conditions.The Apollo Discovery Manual Call Point has been designed to operate on a loop of intelligent fire detection devices. An alarm is initiated by pressing the resettable element. The manual call point signals to the control and indicating equipment using an interrupt feature within the Apollo digital communication protocol.An alarm status is indicated by a yellow and black bar in the lower section of the resettable element and a red LED. The manual call point can be easily reset from the front using the supplied reset key. It is available in two versions with and without isolator. The manual call point is intended for indoor applications.A red alarm LED is provided on the manual call point. This LED is controlled independently of the manual call point by the fire control panel.Once activated the manual call point can be reset by inserting the reset key into front facing LED turning clockwise until a positive click and reset occurs. An additional pack of 10 reset keys can be purchased Part Number 44251-176. The isolated version of the manual call point incorporates a short circuit isolator which will ensure its operation in the event of a short circuit fault on the loop. Isolator operation is indicated by a yellow LED. For further details of the isolator refer to datasheet PP2090 available on request.This manual call point helps reduce installation time as all the initial installation cabling is wired to a terminal block which fits neatly in the back of the call point.

GBP 57.14
1