5 results (0,13267 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Gerband SD2 Control Airtightness Membrane (1.5m x 50m)

Gerband SD2 Control Airtightness Membrane (1.5m x 50m)

Gerband SD2 Control Airtightness Membrane (1.5m x 50m) Product Part Number Gerband SD2 Control Airtightness Membrane - GERBAND-SD2 Description Gerband Air Tightness SD2 Control Membrane is a reliable vapour control layer that enables airtightness and vapour control in roof and wall constructions. During winter, it reliably prevents diffusion of interior humidity into the roof and wall construction. During summer, it allows for back fusion from the insulation as well as the wall and roof construction preventing condensation that facilitates mildew growth and constructional damage.

GBP 132.61
1

Underfloor Heating Manifolds

Underfloor Heating Manifolds

Underfloor Heating Manifolds Product Part Number 2 Port Manifold - SSM002 3 Port Manifold - SSM003 4 Port Manifold - SSM004 5 Port Manifold - SSM005 6 Port Manifold - SSM006 7 Port Manifold - SSM007 8 Port Manifold - SSM008 9 Port Manifold - SSM009 10 Port Manifold - SSM0010 11 Port Manifold - SSM0011 12 Port Manifold - SSM0012 Description Stainless steel manifold for 2 up to 12 heating circuits for distribution, shut off and balancing of the heating / cooling water flow of radiant panel heating / cooling systems in compliance with BS EN 1264-4. The flow rate for each heating circuit will be continuously adjusted via a regulating shut-off valve integrated in the return circuit. Key Features M30x1.5 valve connection for all common actuators (optional accessory) Precise adjustment even at high flow rates Premium quality O-ring valve gaskets (EPDM) ensure permanent ease of operation and high durability 1” MT flat-sealing connections to heat generator, connection to heating circuits via ¾”euro cone for clamp ring screw connection Includes an end set with ¾” swivel connection for shut-off, filling, draining, and flushing Ready-mounted on wall bracket, low noise pipe clamps in accordance with DIN 4109 A wide range of supplementary systems, such as pump groups, hydraulic control units for manifolds, heat interface units and many more   NOTE: Actuators and blending kit are sold seperately  

GBP 132.76
1

Ebac VA32

Ebac VA32

EBAC VA32 R (Right) EBAC VA32 L (Left) Description The EBAC VA32 is a quality Uk manufactured MVHR unit with good controllability and provides a maximum flow rate of 245m3/hr suitable for a house up to 150 m2 floor area with up to 3 kitchens & bathrooms Controllability is provided by a digital touch screen controller that comes complete with the unit and has internal humidity & Co2 sensors for demand-controlled ventilation BPC Ventilation are the largest independent MVHR specialists and supply this unit with up to a 5-year parts warranty* and lifetime technical support on our top-quality systems, KEY FEATURES – EBAC VA32 Digital Touch Screen controller Smart control option Suitable for floor areas up to 172m2 Delivers an airflow rate of up to 288 m³/hour @ 100 Pa High heat recovery efficiency of up to 88%. Internal humidity sensor for automatic speed control Internal Co2 and temperature sensors On demand control via optional room or duct sensor options Full 100% automatic summer bypass to supply unheated air in the summer 2 x G4 filters Galvanised steel casing with 32mm thermal insulation 5-year warranty* (Listed parts Only) 'A' energy rating Left hand right oriented models available Adjustable feet Sap Appendix Q (BRE) approved UK/CA marked Surge protected Integral Humidity Sensor The EBAC unit has an Internal Humidity sensor that can provide a superior demand-controlled ventilation solution for your property When the unit senses that the humidity exceeds the set point the unit will boost to that set by the commissioned boost speed. The humidity can be set on the front of the unit We also advise an optional boost switch should be used local to the wet rooms Filtration 2 x G4 filters are fitted to the unit that are easy and inexpensive to replace CONTROL OPTIONS The EBAC units are controlled by one of the following: Digital touchscreen Controller On-demand ventilation through built-in humidity & Co2 sensors Switched live signal from light / remote switches Heat Exchanger This unit has a high-quality PVC counterflow heat exchanger with up to a 88% thermal efficiency protected with high-capacity filters on each side The heat exchanger is easy to remove for maintenance and any accumulated condensation is easily dispersed via a drain at the bottom of the unit Frost Protection In the event of the intake air temperature at the unit dropping below the predetermined set point (-5°C as standard) the supply fan will reduce to minimum speed, once the temperature rises above the set point the fan will return to its commissioned speed. Frost protection will only activate after ten days of continuous run time. Summer By-Pass The EBAC units have a 100% summer by-Pass If the indoor temperature Intake exceeds 25°C and the outdoor temperature is within comfort zones the summer by-pass is opened automatically to help provide a comfortable indoor temperature Orientation The EBAC VA32 units can be right or left-handed and correct orientation should be checked before purchase Construction Manufactured of double skin powder coated galvanised steel with a 32mm thermal insulation Mounting The units are wall mounted as standard and are supplied with a wall bracket If floor mounting it is recommended to elevate the unit by 150mm to allow access to the condensation drain The four feet are adjustable to allow for any uneven surface Accessories EBAC VA32 Replacement filters - VA32-G4FILTER

GBP 1200.00
1

Awenta Loop DMEV fan with Humidity and Timer

Awenta Loop DMEV fan with Humidity and Timer

Awenta - Loop DMEV fan with Humidity and Timer Product Part Number Awenta Loop DMEV fan with Humidity and Timer - WL100H Description Advanced class leading 125mm continuous running panel axial fan for bathrooms and kitchens. Discreet styling with flat facia to blend into the interior design. Suitable for wall or panel mounting using the appropriate supplied fixing kit. Designed to comply with Building Regulations for whole house system ventilation, this sleek fan can be used in a wet room under System 3 of Building Regulations Approved Document F. This attractive class leading fan is also very energy efficient.  Why choose continuous running fans? Continuous running fans have been designed to meet the requirements of the Building Regulations for bathrooms, kitchens, utility rooms and toilets. Continuous Running Extractor Fans operate by extracting excessive moisture and stale air from a property at a low rate, 24/7. Continuous Running Extractor Fans uses less power than the usual intermittent extractor fans and are therefore a more cost effective to run. As the fan is designed to run all the time, it will keep homes fresh, healthy, and free from condensation.  What does it do? The fan is designed to run continuously at a very low rate and boost automatically when required via its built-in humidity sensor. The normal low running rate means it has extremely low noise levels in operation.  How will it help? This fan will help prevent the build-up of moisture in the home by removing excess moisture (and odours). This will help reduce the risk of black mould forming on walls and behind cupboards etc. The fan will also help promote adequate ventilation within a home by creating an air flow. Awenta was established in 1989 as a family business and today, four generations later, Awenta continues to operate as an independent Polish company. Products are available in Europe, Asia, Africa and North America with all product research, design, production, and distribution being based in Poland.

GBP 34.97
1