6 results (0,14264 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Indexa V227FS Solid Bar Vertical Clamp

Indexa V227FS Solid Bar Vertical Clamp

Designed to improve performance in fabrication and engineering clamping applications. The rapid clamping/unclamping made possible by the use of toggle clamps can greatly reduce machine/operator 'down-time' during all stages of production. Clamping Capacity - the forces stated are the maximum loads that can be applied without causing permanent deformation. Due to leverage ratios, the holding capacity will be greatest at the point on the bar nearest to the handle of the clamp and forces stated have been achieved at this point.

GBP 7.99
1

Indexa 2"x1/8"x24" Aluminium Flat Bar 6082 (1 Pce)

Indexa 2"x1/8"x24" Aluminium Flat Bar 6082 (1 Pce)

Grade 6082 Medium strength alloy with very good corrosion resistance. Additions of magnesium, manganese and silicon enhance the mechanical and corrosion resistance properties. Good cold forming properties, ease of joining, good machinability and high mechanical strengths. Used for packaging containers, foils, tubes, printing plates, strip for heat exchangers, boiler making, insulation foils, kitchenware, chemical and food industry equipment containers, ore skips, automotive trim and light reflectors.

GBP 4.59
1

Indexa 10MMx500MM Brass Round BARCW614N/CZ121 (1 Pce)

Indexa 10MMx500MM Brass Round BARCW614N/CZ121 (1 Pce)

These brass round bars are manufactured from a brass alloy CZ121 / CW614N that is primarily used for machining. Each bar has Lead added to the composition to improve machinability. The Lead remains insoluble in the microstructure of the brass and the soft particles act as chip breakers. Available in two diametersm with both products measuring 500mm in length.Features and Benefits The most widely used of all the brasses due to its suitability for high speed machining operations and also the manufacture of intricate parts The highest machinability of any copper alloy, excellent hot formability and good corrosion resistance Available in two sizes to suit your requirements Both products possess good conductivity, corrosion resistance and spark resistance for all around durabilityTypical Applications Typically used for a wide variety of machined components made on high speed lathes including screws, bolts, nuts, bushing, pins, washers,butts, hinges and also locks and components for watchesNotes Cold working is poor and is not recommended with these bars

GBP 7.99
1

Indexa 8MMx500MM Brass Round BARCW614N/CZ121 (1 Pce)

Indexa 8MMx500MM Brass Round BARCW614N/CZ121 (1 Pce)

These brass round bars are manufactured from a brass alloy CZ121 / CW614N that is primarily used for machining. Each bar has Lead added to the composition to improve machinability. The Lead remains insoluble in the microstructure of the brass and the soft particles act as chip breakers. Available in two diametersm with both products measuring 500mm in length.Features and Benefits The most widely used of all the brasses due to its suitability for high speed machining operations and also the manufacture of intricate parts The highest machinability of any copper alloy, excellent hot formability and good corrosion resistance Available in two sizes to suit your requirements Both products possess good conductivity, corrosion resistance and spark resistance for all around durabilityTypical Applications Typically used for a wide variety of machined components made on high speed lathes including screws, bolts, nuts, bushing, pins, washers,butts, hinges and also locks and components for watchesNotes Cold working is poor and is not recommended with these bars

GBP 7.99
1

Indexa 1.5mm x 10mm x 500mm Ground Flat Stock Gauge Plate - 01 Tool Steel

Indexa 1.5mm x 10mm x 500mm Ground Flat Stock Gauge Plate - 01 Tool Steel

A range of precision ground flat tool steel of the grade 1.2510/ O1 and with a length of 500mm and thickness of 1mm. The product is supplied annealed with all four sides ground and the bar ends saw cut. Ground flat stock is made ready to use on width and thickness, or made close to the finish size in order to save you time, as you don't need to mill or grind material from a raw material plate. This cold work tool steel is typically used to build tools that generally face working temperatures up to 200 C and can be hardened up to 64 HRc. With an excellent general purpose grade, it's the ideal product for manufacturing a great deal of tools. Features and Benefits Supplied in an annealed condition making it easier for you to manipulate the material in a way that suits you Offers good durability, gives excellent wear resistance and holds an excellent cutting edge Available in a wide range of metric sizes to help avoid material losses as you can purchase the size required for your individual application With a steel grade of 1.2510/O1 this product is easy to harden Offers a high wear-resistance and high dimensional stability making it a robust product Typical Applications Can be used for the production of knives, stamping dies, wood cutting tools or for mould making applications Notes Material Specification: Nearest AISI Standard: O1 Hardness: 230 HB Surface Roughness: max. 3.2m

GBP 7.99
1