16 resultater (0,22021 sekunder)

Vis alle filtre

Mærke

Vis alle

Butik

Pris (EUR)

Nulstil filter

Produkter
Fra
Butikker

Castle Creations Wire harness Deans parallel - 011-0006-00

Castle Creations Wire harness Deans parallel - 011-0006-00

This harness will connect two battery packs in parallel. You will effectively combine the capacity (mAh) of the packs. Example: two 3S (11.1V) 6000mAh packs will have the capacity of 12,000mAh when combined with this harness, but remain at a 3S (11.1V) voltage.Note: You must always use identically prepared packs. Both packs must be fully charged and properly balanced. Both packs must be made by the same manufacturer, have the same C rating, same number of cells (2s,3s,etc.), and both must have the same capacity.

DKK 139.00
1

RPM Wheelie Bar (Low Visibility) X-Maxx (Only with RPM 81762) - 81582

RPM Wheelie Bar (Low Visibility) X-Maxx (Only with RPM 81762) - 81582

RPM Low Visibility Wheelie Bar for X-MaxxQuick Notes:Protection for the low hanging rear bumper of the X-MaxxWorks with RPM 81762 Rear Bumper Mounts only (sold separately)RPM Low Visibility Wheelie Bars are designed to take the stress off of the low hanging rear bumper whenever the rear end wants to drag on the ground. The wheels we designed are large enough to touch down before the rear bumper does in 99% of normal acceleration wheelies, eliminating your fears of blowing the rear bumper off of the truck or using the rear bumper as a plow.Each set of Low Visibility Wheelie Bars is made from our nearly indestructible blend of engineering grade nylons and made right here in the USA.Tech Notes: RPM Low Visibility Wheelie Bars only work with RPM 81762 Rear Bumper Mounts. They will not work with stock or any other known aftermarket rear bumper mounts.

DKK 127.00
1

Kwik Sand Hand Sander 140 mm (1)

Kwik Sand Hand Sander 140 mm (1)

Du-Bro 3400-55 - Kwik Sand Hand Sander 5.5"/140mmThese aluminum sanding bars are lightweight and durable. Their contoured handle provides a secure, comfortable grip.Kwik Sand hand sanders are available in 5.5 (Part 3400-55) and 11 (Part 3400-11) lengths. They are designed to use precut, self-adhesive sandpaper that is easy to apply. Each Kwik Sand hand sander includes a 3-pack of sandpaper with(1) 80, (1) 150, and (1) 220 grit pieces. Because the sandpaper is already the perfect size, you just peel, stick, and start sanding!We also offer 6/pkg. pre-cut premium, self adhering, sandpaper in 80, 150, & 220 grit. A perfect fit for the Kwik sand!Du-Bro designed Kwik Sand hand sanders with the hobbyist in mind. But we think you will find uses for them all around the house!

DKK 139.00
1

PL9054-001 Suppressor X1 Firm (2)

PL9054-001 Suppressor X1 Firm (2)

This is a Suppressor 1:8 Buggy Race Tire. The Suppressor is Pro-Line’s latest race tire designed specifically for medium packed to loose outdoor tracks. The tread design takes inspiration from Pro-Line’s incredibly successful line of race tires like the Hole Shot, Lock Down and Tazer but brings a whole new level of performance! The Suppressor features a smooth transition from the sidewall to the tread to prevent catching the sharp edges in the track, which can cause violent roll overs and lost time. The long center bars on the Suppressor provide massive forward bite and have a Hole Shot style relief cut for added side to side tread flex. Below the center tread is reinforcement webbing that mimics the outside pattern for a cohesive Suppressor look.When combined with Pro-Line’s incredible X-Compounds, the Suppressor tires easily become the loose track tire of choice in a high performance package that is second to none!Don’t get left behind with old tire technology, jump into the future with the all new Pro-Line Suppressor!The Ultimate Medium to Loose Surface TireBased on the Successful Hole Shot, Lock Down and TazerReduced Edginess for Improved ControlNo more Violent Roll Overs and Lost TimeMore Side Traction And Faster ResponseMassive Forward BiteImproved Traction with X-Compound TechnologyLong lasting Closed Cell Inserts includedMade in the USAIncluded:Suppressor 1:8 Buggy Race Tires (2 pcs)Closed Cell Foam Inserts (2 pcs)

DKK 119.00
1

RPM Light Bar Roof (4 Lights) Black (LED not included) - 80782

RPM Light Bar Roof (4 Lights) Black (LED not included) - 80782

RPM Narrow Roof-Mounted Light Bar Set - BlackQuick Notes:Fits most bodies with a minimum 100mm body widthLED?s are not includedOur first Roof-Mounted Light Bar Sets worked on all 1/8th and 1/10th scale Short Course bodies, leaving a huge gap in who could run lights on their vehicles. The RPM Narrow Roof-Mounted Light Bar Set cuts a full 2" off of the width, reducing the number of LED light canisters to four and allows virtually anyone running a vehicle with a minimum 4" body width to run LED lights on their vehicle. The list of vehicles this includes is quite extensive, including many popular sellers such as: Traxxas T-Maxx, Traxxas Revo, Traxxas 1/16th scale Mini Slash, Traxxas Rustler, Traxxas Stampede, Associated MGT, Associated T4, HPI Savage, HPI E-Firestorm, HPI E-Firestorm Flux, Losi LST/LST2, Losi XXX-T, Duratrax Evader and many, many more!The goal of our Narrow Roof-Mounted Light Bar Set was to recreate a scale version of those light bars found in full-sized racing while striving for some reasonable amount of crash-survivability. Our Light Bar Set uses a unique hinged system that in the event of a rollover, the light bar will fold against the body to help reduce impact damage. The light set is designed to bolt to the front windshield of the truck (although with sufficient room, it can be mounted to the rear window as well), keeping the profile low and in the perfect position to light up the night. Each kit comes with a pair of large backing plates that help protect the body where the screws hold the light bar in place.Each kit comes complete with all necessary mounting hardware, light canisters, molded parts and instructions. The instructions also show how to easily create your own LED light set-up with a few basic electronics skills, some tools and a little patience.We mold these light bar sets in black and chrome to match or contrast any paint and color scheme.Tech Notes: LED lights are not included. The RPM Narrow Roof-Mounted Light Bar Set can fit any number of applications. Due to the scale appearance of this light bar set, we cannot properly strengthen all aspects of the lights. Therefore, some warranty restrictions may apply. See instructions for complete details.

DKK 135.00
1

RPM Light Bar Roof (4 Lights) Chrome (LED not included) - 80783

RPM Light Bar Roof (4 Lights) Chrome (LED not included) - 80783

RPM Narrow Roof-Mounted Light Bar Set - Chromed Quick Notes: Fits most bodies with a minimum 100mm body width LED?s are not included Our first Roof-Mounted Light Bar Sets worked on all 1/8th and 1/10th scale Short Course bodies, leaving a huge gap in who could run lights on their vehicles. The RPM Narrow Roof-Mounted Light Bar Set cuts a full 2" off of the width, reducing the number of LED light canisters to four and allows virtually anyone running a vehicle with a minimum 4" body width to run LED lights on their vehicle. The list of vehicles this includes is quite extensive, including many popular sellers such as: Traxxas T-Maxx, Traxxas Revo, Traxxas 1/16th scale Mini Slash, Traxxas Rustler, Traxxas Stampede, Associated MGT, Associated T4, HPI Savage, HPI E-Firestorm, HPI E-Firestorm Flux, Losi LST/LST2, Losi XXX-T, Duratrax Evader and many, many more!The goal of our Narrow Roof-Mounted Light Bar Set was to recreate a scale version of those light bars found in full-sized racing while striving for some reasonable amount of crash-survivability. Our Light Bar Set uses a unique hinged system that in the event of a rollover, the light bar will fold against the body to help reduce impact damage. The light set is designed to bolt to the front windshield of the truck (although with sufficient room, it can be mounted to the rear window as well), keeping the profile low and in the perfect position to light up the night. Each kit comes with a pair of large backing plates that help protect the body where the screws hold the light bar in place.Each kit comes complete with all necessary mounting hardware, light canisters, molded parts and instructions. The instructions also show how to easily create your own LED light set-up with a few basic electronics skills, some tools and a little patience.We mold these light bar sets in black and chrome to match or contrast any paint and color scheme.Tech Notes: LED lights are not included. The RPM Narrow Roof-Mounted Light Bar Set can fit any number of applications. Due to the scale appearance of this light bar set, we cannot properly strengthen all aspects of the lights. Therefore, some warranty restrictions may apply. See instructions for complete details.

DKK 152.00
1