8 resultater (0,22861 sekunder)

Vis alle filtre

Mærke

Butik

Pris (EUR)

Nulstil filter

Produkter
Fra
Butikker

Steel Gutter Union - 120mm Graphite Grey

Steel Gutter Union - 120mm Graphite Grey

Installation of this union is a simple process. Slide the union fully onto one length of gutter, and position the next length of gutter alongside leaving a gap of no more than 2mm. Slide the union into position and use the rear locking tabs to clamp the gutter in place. Pull out the locking tab on the front of the union body, lower the clamp down onto the gutter and secure in place using the locking tab.This type of union should be supported with a fascia bracket (or rafter bracket) fitted within 150mm on each side.We recommend the use of silicon spray on all rubber seals to improve adhesion and long term seal performance.

GBP 6.96
1

Steel Downpipe Bend - 90 Degree x 87mm Black

Steel Downpipe Bend - 90 Degree x 87mm Black

92.5 Bends are used in a steel guttering system to change the plane of the downpipe bend from vertical to horizontal or vice versa.They are often used instead of offset bends when the soffit is particularly wide - this enables the pipe to run neatly below the soffit rather than dropping down diagonally back to the wall as it would with a normal swan neck setup.This bend also doubles up as a shoe for the bottom of the downpipe if it is not being connected directly into the drainage system.The finish on the galvanised 90 Degree bend is very slightly different due to the manufacturing process, although the difference is not noticeable unless used at level.

GBP 28.21
1

Steel Downpipe Bend - 90 Degree x 87mm Galvanised

Steel Downpipe Bend - 90 Degree x 87mm Galvanised

92.5 Bends are used in a steel guttering system to change the plane of the downpipe bend from vertical to horizontal or vice versa.They are often used instead of offset bends when the soffit is particularly wide - this enables the pipe to run neatly below the soffit rather than dropping down diagonally back to the wall as it would with a normal swan neck setup.This bend also doubles up as a shoe for the bottom of the downpipe if it is not being connected directly into the drainage system.The finish on the galvanised 90 Degree bend is very slightly different due to the manufacturing process, although the difference is not noticeable unless used at level.

GBP 36.56
1

Steel Downpipe Bend - 90 Degree x 87mm Graphite Grey

Steel Downpipe Bend - 90 Degree x 87mm Graphite Grey

92.5 Bends are used in a steel guttering system to change the plane of the downpipe bend from vertical to horizontal or vice versa.They are often used instead of offset bends when the soffit is particularly wide - this enables the pipe to run neatly below the soffit rather than dropping down diagonally back to the wall as it would with a normal swan neck setup.This bend also doubles up as a shoe for the bottom of the downpipe if it is not being connected directly into the drainage system.The finish on the galvanised 90 Degree bend is very slightly different due to the manufacturing process, although the difference is not noticeable unless used at level.

GBP 28.21
1

Steel Downpipe Bend - 90 Degree x 100mm Galvanised

Steel Downpipe Bend - 90 Degree x 100mm Galvanised

92.5 Bends are used in a steel guttering system to change the plane of the downpipe bend from vertical to horizontal or vice versa.They are often used instead of offset bends when the soffit is particularly wide - this enables the pipe to run neatly below the soffit rather than dropping down diagonally back to the wall as it would with a normal swan neck setup.This bend also doubles up as a shoe for the bottom of the downpipe if it is not being connected directly into the drainage system.The finish on the galvanised 90 Degree bend is very slightly different due to the manufacturing process, although the difference is not noticeable unless used at level.

GBP 32.24
1

Steel Downpipe Bend - 90 Degree x 87mm Copper Effect

Steel Downpipe Bend - 90 Degree x 87mm Copper Effect

92.5 Bends are used in a steel guttering system to change the plane of the downpipe bend from vertical to horizontal or vice versa.They are often used instead of offset bends when the soffit is particularly wide - this enables the pipe to run neatly below the soffit rather than dropping down diagonally back to the wall as it would with a normal swan neck setup.This bend also doubles up as a shoe for the bottom of the downpipe if it is not being connected directly into the drainage system.The finish on the galvanised 90 Degree bend is very slightly different due to the manufacturing process, although the difference is not noticeable unless used at level.

GBP 28.21
1